S-24CM01C.pdf 데이터시트 (총 30 페이지) - 파일 다운로드 S-24CM01C 데이타시트 다운로드

No Preview Available !

S-24CM01C
www.sii-ic.com
© SII Semiconductor Corporation, 2010-2013
2-WIRE SERIAL E2PROM
Rev.2.0_02_S
The S-24CM01C is a 2-wire, low current consumption and wide range operation serial E2PROM. The S-24CM01C has the
capacity of 1 M-bit, and the organization is 131072 words × 8-bit. Page write and sequential read are available.
Features
Operating voltage range
Read:
1.6 V to 5.5 V
Write:
1.7 V to 5.5 V
Page write:
256 bytes / page
Sequential read
Operation frequency:
1.0 MHz (VCC = 2.5 V to 5.5 V)
400 kHz (VCC = 1.6 V to 2.5 V)
Write time:
5.0 ms max.
Noise suppression:
Schmitt trigger and noise filter on input pins (SCL, SDA)
Write protect function during the low power supply voltage
Endurance:
106cycles / unit*1 (Ta = +25°C)
Data retention:
100 years (Ta = +25°C)
Memory capacity:
1 M-bit
Write protect:
100%
Initial shipment data:
FFh
Lead-free (Sn 100%), halogen-free*2
*1. For each unit (unit: the 4 bytes with the same address of P0, W15 to W2)
*2. Refer to “Product Name Structure” for details.
Package
8-Pin SOP (JEDEC)
Caution
This product is intended to use in general electronic devices such as consumer electronics,
office equipment, and communications devices. Before using the product in medical equipment
or automobile equipment including car audio, keyless entry and engine control unit, contact to
SII Semiconductor Corporation is indispensable.
1

No Preview Available !

2-WIRE SERIAL E2PROM
S-24CM01C
Rev.2.0_02_S
Pin Configuration
1. 8-Pin SOP (JEDEC)
8-Pin SOP (JEDEC)
Top view
18
27
36
45
Figure 1
S-24CM01CI-J8T1U4
Table 1
Pin No
Symbol
Description
1
NC*1
No connection
2 A1 Slave address input
3 A2 Slave address input
4
GND
Ground
5
SDA*2
Serial data I/O
6
SCL*2
Serial clock input
Write protect input
7
WP Connected to VCC:
Protection valid
Open or connected to GND: Protection invalid
8
VCC
Power supply
*1. Connect to GND or VCC.
*2. Do not use it in high impedance.
Remark Refer to the “Package drawings” for the details.
2

No Preview Available !

Rev.2.0_02_S
Block Diagram
SCL
SDA
A2
A1
Start / Stop
Detector
LOAD
Device Address
Comparator
Serial Clock
Controller
COMP
LOAD INC
R/W
Address
Counter
Y Decoder
DIN
DOUT
Figure 2
2-WIRE SERIAL E2PROM
S-24CM01C
VCC
WP
GND
Voltage Detector
High-Voltage Generator
Data Register
X Decoder Memory Cell Array
Selector
Data Output
ACK Output
Controller
3

No Preview Available !

2-WIRE SERIAL E2PROM
S-24CM01C
Rev.2.0_02_S
Absolute Maximum Ratings
Table 2
Item
Symbol
Absolute Maximum Ratings
Unit
Power supply voltage
VCC
0.3 to +6.5
V
Input voltage
Output voltage
VIN
VOUT
0.3 to +6.5
0.3 to +6.5
V
V
Operation ambient temperature
Storage temperature
Topr
Tstg
40 to +85
65 to +150
°C
°C
Caution The absolute maximum ratings are rated values exceeding which the product could suffer
physical damage. These values must therefore not be exceeded under any conditions.
Recommended Operating Conditions
Table 3
Item
Power supply voltage
High level input voltage
Low level input voltage
Symbol
Condition
VCC
Read Operation
Write Operation
VIH
VCC = 1.8 V to 5.5 V
VCC = 1.6 V to 1.8 V
VIL
VCC = 1.8 V to 5.5 V
VCC = 1.6 V to 1.8 V
Ta = 40°C to +85°C
Min. Max.
1.6 5.5
1.7 5.5
0.7 × VCC
0.8 × VCC
5.5
5.5
0.3
0.3
0.3 × VCC
0.2 × VCC
Unit
V
V
V
V
V
V
Pin Capacitance
Item
Input capacitance
I/O capacitance
Table 4
Symbol
CIN
CI / O
Condition
VIN = 0 V (SCL, A1, A2, WP)
VI / O = 0 V (SDA)
(Ta = +25°C, f = 1.0 MHz, VCC = 5.0 V)
Min.
Max.
Unit
10 pF
10 pF
Endurance
Table 5
Item
Symbol Operation Ambient Temperature
Min.
Endurance
NW
Ta = +25°C
106
*1. For each unit (unit: the 4 bytes with the same address of P0, W15 to W2)
Max.
Unit
cycles / unit*1
Data Retention
Item
Data retention
Symbol
Table 6
Operation Ambient Temperature
Ta = +25°C
Min.
100
Max.
Unit
year
4

No Preview Available !

Rev.2.0_02_S
2-WIRE SERIAL E2PROM
S-24CM01C
DC Electrical Characteristics
Item
Current consumption (READ)
Symbol
ICC1
Table 7
Condition
Ta = 40°C to +85°C
VCC = 2.5 V to 5.5 V
fSCL = 1.0 MHz
Min. Max.
VCC = 1.6 V to 2.5 V
fSCL = 400 kHz
Min. Max.
2.0 1.5
Unit
mA
Item
Current consumption (WRITE)
Symbol
ICC2
Table 8
Condition
Ta = 40°C to +85°C
VCC = 2.5 V to 5.5 V
fSCL = 1.0 MHz
VCC = 1.7 V to 2.5 V
fSCL = 400 kHz
Min. Max. Min. Max.
4.0 4.0
Unit
mA
Table 9
Item
Symbol
Condition
Standby current consumption ISB
Input leakage current 1
ILI1
Input leakage current 2
ILI2
Output leakage current
Input current 1
Input current 2
Input Impedance 1
Input Impedance 2
ILO
IIL
IIH
ZIL
ZIH
Low level output voltage
VOL
VIN = VCC or GND
SCL, SDA,
VIN = GND to VCC
A1, A2
VIN > 0.7 × VCC
At standby mode
SDA
VOUT = GND to VCC
WP
VIN < 0.3 × VCC
WP
VIN > 0.7 × VCC
WP
VIN = 0.3 × VCC
WP
VIN = 0.7 × VCC
IOL = 3.2 mA
IOL = 1.5 mA
IOL = 0.7 mA
Ta = 40°C to +85°C
VCC = 2.5 V to 5.5 V
VCC = 1.6 V to 2.5 V
Min. Max. Min. Max.
10.0
4.0
1.0 1.0
1.0 1.0
1.0 1.0
50.0 50.0
2.0 2.0
30 30
500 500
0.4
0.3 0.3
0.2 0.2
Unit
μA
μA
μA
μA
μA
μA
kΩ
kΩ
V
V
V
5