IASX16H.pdf 데이터시트 (총 29 페이지) - 파일 다운로드 IASX16H 데이타시트 다운로드

No Preview Available !

Engineering Specification
Engineering Specification
Type 14.1 SXGA+ Color TFT/LCD Module
Model Name:IASX16H
Document Control Number : OEM I-916H-03
Note:Specification is subject to change without notice. Consequently it is better to contact to
International Display Technology before proceeding with the design
of your product incorporating this module.
Sales Support
International Display Technology
(C) Copyright International Display Technology 2001,2002 All Rights reserved.
April 15,2002
OEM I-916H-03
1/29

No Preview Available !

Engineering Specification
i Contents
i Contents
ii Record of Revision
1.0 Handling Precautions
2.0 General Description
2.1 Characteristics
2.2 Functional Block Diagram
3.0 Absolute Maximum Ratings
4.0 Optical Characteristics
5.0 Signal Interface
5.1 Connectors
5.2 Interface Signal Connector
5.3 Interface Signal Description
5.4 Interface Signal Electrical Characteristics
5.4.1 Signal Electrical Characteristics for LVDS Receiver
5.4.2 LVDS Receiver Internal Circuit
5.4.3 Recommended Guidelines for Motherboard PCB Design and Cable Selection
5.5 Inverter Signal Connector
5.6 Inverter Signal Description
5.7 Inverter Signal Electrical Characteristics
6.0 Pixel format image
7.0 Interface Timings
7.1 Timing Characteristics
7.2 Timing Definition
8.0 Power Consumption
9.0 Power ON/OFF Sequence
10.0 Mechanical Characteristics
11.0 National Test Lab Requirement
(C) Copyright International Display Technology 2001,2002 All Rights reserved.
April 15,2002
OEM I-916H-03
2/29

No Preview Available !

Engineering Specification
ii Record of Revision
Date
December 5,2001
Document
Revision
OEM I-916H-01
Page
All
February 7,2002
April 15,2002
OEM I-916H-02
OEM I-916H-03
6
15
16
18
20
23
6
8
9
17
20
21
Summary
First Edition for customer.
Based on Internal Spec. EC H31250 as of November
9,2001.
To adopt a "Burst Mode Inverter".
Based on Internal Spec. as of December 3,2001.
To update Backlight Power Consumption.
To update Physical Size.
To update Timing Requirements.
To add Figure of Timing Definition.
To update Input Circuit of LVDS Signals.
To add Brightness.
To update Timing Characteristics.
Based on Internal Spec. EC H31252 as of April
11,2002.
To update Contrast Ratio, Weight and Physical Size.
To update the value of Shock.
To update Contrast Ratio, Response Time and Color
Chromaticity.
To update Timing Definition (detail A).
To add Cycle Modulation Rate.
To update Inverter Signal Electrical Characteristics.
To update the SMData versus the Luminance.
(C) Copyright International Display Technology 2001,2002 All Rights reserved.
April 15,2002
OEM I-916H-03
3/29

No Preview Available !

Engineering Specification
1.0 Handling Precautions
O If any signals or power lines deviate from the power on/off sequence, it may cause shorten the life of the
LCD module.
O The LCD panel and the CFL are made of glass and may break or crack if dropped on a hard surface, so
please handle them with care.
O CMOS ICs are included in the LCD panel. They should be handled with care, to prevent electrostatic
discharge.
O Do not press the reflector sheet at the LCD module to any directions.
O Do not stick the adhesive tape on the reflector sheet at the back of the LCD module.
O Please handle with care when mount in the system cover. Mechanical damage for lamp cable/lamp
connector may cause safety problems.
O Small amount of materials having no flammability grade is used in the LCD module. The LCD module
should be supplied by power complied with requirements of Limited Power Source (2.11, IEC60950 or
UL1950), or be applied exemption conditions of flammability requirements (4.4.3.3, IEC60950 or UL1950)
in an end product.
O The fluorescent lamp in the liquid crystal display(LCD) contains mercury. Do not put it in trash that is
disposed of in landfills. Dispose of it as required by local ordinances or regulations.
O Never apply detergent or other liquid directly to the screen.
O Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
O When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth; do not use solvents or
abrasives.
O Do not touch the front screen surface in your system, even bezel.
O The information contained herein is presented only as a guide for the applications of our
products. No responsibility is assumed by International Display Technology for any
infringements of patents or other right of the third partied which may result from its use. No
license is granted by implication or otherwise under any patent or patent rights of International
Display Technology or others.
O The information contained herein may be changed without prior notice. It is therefore
advisable to contact International Display Technology before proceeding with the design of
equipment incorporating this product.
(C) Copyright International Display Technology 2001,2002 All Rights reserved.
April 15,2002
OEM I-916H-03
4/29

No Preview Available !

Engineering Specification
2.0 General Description
This specification applies to the Type 14.1 Color TFT/LCD Module 'IASX16H'.
This module is designed for a display unit of notebook style personal computer.
The screen format and electrical interface are intended to support the SXGA+ (1400(H) x 1050(V))screen.
Support color is native 262k colors ( RGB 6-bit data driver ).
All input signals are LVDS interface compatible. This module contains an inverter card for backlight.
(C) Copyright International Display Technology 2001,2002 All Rights reserved.
April 15,2002
OEM I-916H-03
5/29