R0990LC08A.pdf 데이터시트 (총 12 페이지) - 파일 다운로드 R0990LC08A 데이타시트 다운로드

No Preview Available !

Date:- 01 August 2012
Data Sheet Issue:- 3
Distributed Gate Thyristor
Type R0990LC08x
(Old Type Number: R270CH04-08)
Absolute Maximum Ratings
VDRM
VDSM
VRRM
VRSM
VOLTAGE RATINGS
Repetitive peak off-state voltage, (note 1)
Non-repetitive peak off-state voltage, (note 1)
Repetitive peak reverse voltage, (note 1)
Non-repetitive peak reverse voltage, (note 1)
MAXIMUM
LIMITS
800
900
800
900
OTHER RATINGS
IT(AV)M
IT(AV)M
IT(AV)M
IT(RMS)
IT(d.c.)
ITSM
ITSM2
I2t
I2t
(di/dt)cr
VRGM
PG(AV)
PGM
Tj op
Tstg
Maximum average on-state current, Tsink=55°C, (note 2)
Maximum average on-state current. Tsink=85°C, (note 2)
Maximum average on-state current. Tsink=85°C, (note 3)
Nominal RMS on-state current, Tsink=25°C, (note 2)
D.C. on-state current, Tsink=25°C, (note 4)
Peak non-repetitive surge tp=10ms, Vrm=60%VRRM, (note 5)
Peak non-repetitive surge tp=10ms, Vrm10V, (note 5)
I2t capacity for fusing tp=10ms, Vrm=60%VRRM, (note 5)
I2t capacity for fusing tp=10ms, Vrm10V, (note 5)
Maximum rate of rise of on-state current (repetitive), (note 6)
Maximum rate of rise of on-state current (non-repetitive), (note 6)
Peak reverse gate voltage
Mean forward gate power
Peak forward gate power
Operating temperature range
Storage temperature range
Notes:-
1) De-rating factor of 0.13% per °C is applicable for Tj below 25°C.
2) Double side cooled, single phase; 50Hz, 180° half-sinewave.
3) Single side cooled, single phase; 50Hz, 180° half-sinewave.
4) Double side cooled.
5) Half-sinewave, 125°C Tj initial.
6) VD=67% VDRM, IFG=2A, tr0.5µs, Tcase=125°C.
MAXIMUM
LIMITS
990
652
373
2001
1627
11000
12000
605×103
720×103
1000
1500
5
2
30
-40 to +125
-40 to +150
UNITS
V
V
V
V
UNITS
A
A
A
A
A
A
A
A2s
A2s
A/µs
V
W
W
°C
°C
Data Sheet. Type R0990LC08x Issue 3
Page 1 of 12
August 2012

No Preview Available !

Characteristics
Distributed Gate Thyristor Type R0990LC08x
PARAMETER
VTM Maximum peak on-state voltage
VT0 Threshold voltage
rT Slope resistance
(dv/dt)cr Critical rate of rise of off-state voltage
IDRM Peak off-state current
IRRM Peak reverse current
VGT Gate trigger voltage
IGT Gate trigger current
VGD Gate non-trigger voltage
IH Holding current
tgd Gate controlled turn-on delay time
tgt Turn-on time
Qrr Recovered charge
Qra Recovered charge, 50% Chord
Irm Reverse recovery current
trr Reverse recovery time
tq Turn-off time (note 2)
RthJK
F
Wt
Thermal resistance, junction to heatsink
(note 3)
Mounting force
Weight
MIN.
-
-
-
200
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
10
-
TYP. MAX. TEST CONDITIONS (Note 1)
-
-
-
-
-
-
-
-
-
-
0.4
1.0
90
40
55
1.55
10
12
-
-
-
340
1.84 ITM=1400A
1.35
0.35
- VD=80% VDRM, Linear ramp, Gate o/c
70 Rated VDRM
70 Rated VRRM
3.0
Tj=25°C
300
VD=10V, IT=3A
0.25
1000
1.0
2.0
Rated VDRM
Tj=25°C
VD=67% VDRM, ITM=1500A, di/dt=60A/µs,
IFG=2A, tr=0.5µs, Tj=25°C
105
- ITM=1000A, tp=1000µs, di/dt=60A/µs,
- Vr=50V
-
-
-
0.032
ITM=1000A, tp=1000µs, di/dt=60A/µs,
Vr=50V, Vdr=33%VDRM, dVdr/dt=20V/µs
IITM=1000A, tp=1000µs, di/dt=60A/µs,
Vr=50V, Vdr=33%VDRM, dVdr/dt=200V/µs
Double side cooled
0.064 Single side cooled
20
- Outline option LC
UNITS
V
V
m
V/µs
mA
mA
V
mA
V
mA
µs
µC
µC
A
µs
µs
K/W
K/W
kN
g
Notes:-
1) Unless otherwise indicated Tj=125°C.
2) The required tq (specified with dVdr/dt=200V/µs) is represented by ‘x’ in the device part number. See ordering
information for details of tq codes.
3) For other clamp forces, please consult factory
Data Sheet. Type R0990LC08x Issue 3
Page 2 of 12
August 2012

No Preview Available !

Distributed Gate Thyristor Type R0990LC08x
Notes on Ratings and Characteristics
1.0 Voltage Grade Table
Voltage Grade
08
VDRM VDSM
V
800
VRRM
V
800
VRSM
V
900
VD
DC V
900
VR
DC V
530
2.0 Extension of Voltage Grades
This report is applicable to other and higher voltage grades when supply has been agreed by
Sales/Production.
3.0 Extension of Turn-off Time
This Report is applicable to other tq/re-applied dv/dt combinations when supply has been agreed by
Sales/Production.
4.0 Repetitive dv/dt
Higher dv/dt selections are available up to 1000V/µs on request.
5.0 De-rating Factor
A blocking voltage de-rating factor of 0.13%/°C is applicable to this device for Tj below 25°C.
6.0 Snubber Components
When selecting snubber components, care must be taken not to use excessively large values of snubber
capacitor or excessively small values of snubber resistor. Such excessive component values may lead to
device damage due to the large resultant values of snubber discharge current. If required, please consult
the factory for assistance.
7.0 Rate of rise of on-state current
The maximum un-primed rate of rise of on-state current must not exceed 1500A/µs at any time during
turn-on on a non-repetitive basis. For repetitive performance, the on-state rate of rise of current must not
exceed 1000A/µs at any time during turn-on. Note that these values of rate of rise of current apply to the
total device current including that from any local snubber network.
8.0 Gate Drive
The nominal requirement for a typical gate drive is illustrated below. An open circuit voltage of at least
30V is assumed. This gate drive must be applied when using the full di/dt capability of the device.
IGM
4A/µs
IG
tp1
The magnitude of IGM should be between five and ten times IGT, which is shown on page 2. Its duration
(tp1) should be 20µs or sufficient to allow the anode current to reach ten times IL, whichever is greater.
Otherwise, an increase in pulse current could be needed to supply the necessary charge to trigger. The
‘back-porch’ current IG should remain flowing for the same duration as the anode current and have a
magnitude in the order of 1.5 times IGT.
Data Sheet. Type R0990LC08x Issue 3
Page 3 of 12
August 2012