N0180SH120.pdf 데이터시트 (총 9 페이지) - 파일 다운로드 N0180SH120 데이타시트 다운로드

No Preview Available !

Date:- 21st June, 2016
Data Sheet Issue:- K2
Phase Control Thyristor
Types N0180SH120 to N0180SH160
Absolute Maximum Ratings
VDRM
VDSM
VRRM
VRSM
VOLTAGE RATINGS
Repetitive peak off-state voltage, (note 1)
Non-repetitive peak off-state voltage, (note 1)
Repetitive peak reverse voltage, (note 1)
Non-repetitive peak reverse voltage, (note 1)
MAXIMUM
LIMITS
1200-1600
1200-1600
1200-1600
1300-1700
UNITS
V
V
V
V
IT(AV)
IT(AV)
IT(RMS)
IT(d.c.)
ITSM
ITSM2
I2t
I2t
(di/dt)cr
VFGM
IFGM
VRGM
PG(AV)
PGM
VGD
THS
Tstg
OTHER RATINGS
Mean on-state current, Tsink=55°C, (note 2)
Mean on-state current. Tsink=85°C, (note 2)
Nominal RMS on-state current, Tsink=25°C, (note 2)
D.C. on-state current, Tsink=25°C, (note 4)
Peak non-repetitive surge tp=10ms, VRM=0.6VRRM, (note 5)
Peak non-repetitive surge tp=10ms, VRM10V, (note 5)
I2t capacity for fusing tp=10ms, VRM=0.6VRRM, (note 5)
I2t capacity for fusing tp=10ms, VRM10V, (note 5)
Maximum rate of rise of on-state current (repetitive), (Note 6)
Maximum rate of rise of on-state current (non-repetitive), (Note 6)
Peak forward gate voltage
Peak forward gate current
Peak reverse gate voltage
Mean forward gate power
Peak forward gate power (100µs pulse width)
Non-trigger gate voltage, (Note 7)
Operating temperature range
Storage temperature range
Notes:-
1) De-rating factor of 0.13% per °C is applicable for Tj below 25°C.
2) Double side cooled, single phase; 50Hz, 180° half-sinewave.
3) Single side cooled, single phase; 50Hz, 180° half-sinewave.
4) Double side cooled.
5) Half-sinewave, 125°C Tj initial.
6) VD=80% VDRM, IFG=1A, tr1µs, Tcase=125°C.
7) Rated VDRM.
MAXIMUM
LIMITS
180
110
175
175
2450
2695
30×103
36.3×103
500
1000
12
19
5
2
100
0.25
-40 to +125
-40 to +150
UNITS
A
A
A
A
A
A
A2s
A2s
A/µs
A/µs
V
A
V
W
W
V
°C
°C
Data Sheet. Types N0180SH120-160 Issue K2
Page 1 of 9
June 2016

No Preview Available !

Characteristics
Phase control thyristor types N0180SH120-160
PARAMETER
VTM Maximum peak on-state voltage
VT0 Threshold voltage
rT Slope resistance
(dv/dt)cr Critical rate of rise of off-state voltage
IDRM Peak off-state current
IRRM Peak reverse current
VGT Gate trigger voltage
IGT Gate trigger current
IH Holding current
RthJC Thermal resistance, junction to case
F Mounting torque
Wt Weight
Notes:-
1) Unless otherwise indicated Tj=125°C.
MIN.
-
-
-
1000
-
-
-
-
-
-
-
-
TYP. MAX. TEST CONDITIONS (Note 1)
- 1.57 ITM=715A
- 0.9
- 1.79
- - VD=80% VDRM
- 20 Rated VDRM
- 20 Rated VRRM
- 3.0 Tj=25°C
- 150 Tj=25°C
VD=6V, IT=1A
- 600 Tj=25°C
- 0.23 Double side cooled
- 14
130 -
UNITS
V
V
m
V/s
mA
mA
V
mA
mA
K/W
Nm
g
Data Sheet. Types N0180SH120-160 Issue K2
Page 2 of 9
June 2016

No Preview Available !

Phase control thyristor types N0180SH120-160
Notes on Ratings and Characteristics
1.0 Voltage Grade Table
Voltage Grade
12
14
16
VDRM VDSM VRRM
V
1200
1400
1600
VRSM
V
1300
1500
1700
VD VR
DC V
810
930
1040
2.0 Extension of Voltage Grades
This report is applicable to other voltage grades when supply has been agreed by Sales/Production.
3.0 De-rating Factor
A blocking voltage de-rating factor of 0.13%/°C is applicable to this device for Tj below 25°C.
4.0 Repetitive dv/dt
Standard dv/dt is 1000V/µs.
5.0 Snubber Components
When selecting snubber components, care must be taken not to use excessively large values of snubber
capacitor or excessively small values of snubber resistor. Such excessive component values may lead to
device damage due to the large resultant values of snubber discharge current. If required, please consult
the factory for assistance.
6.0 Rate of rise of on-state current
The maximum un-primed rate of rise of on-state current must not exceed 1000A/µs at any time during
turn-on on a non-repetitive basis. For repetitive performance, the on-state rate of rise of current must not
exceed 500A/µs at any time during turn-on. Note that these values of rate of rise of current apply to the
total device current including that from any local snubber network.
7.0 Gate Drive
The nominal requirement for a typical gate drive is illustrated below. An open circuit voltage of at least 30V
is assumed. This gate drive must be applied when using the full di/dt capability of the device.
IGM
4A/µs
tp1
IG
The magnitude of IGM should be between five and ten times IGT, which is shown on page 2. Its duration
(tp1) should be 20µs or sufficient to allow the anode current to reach ten times IL, whichever is greater.
Otherwise, an increase in pulse current could be needed to supply the necessary charge to trigger. The
‘back-porch’ current IG should remain flowing for the same duration as the anode current and have a
magnitude in the order of 1.5 times IGT.
Data Sheet. Types N0180SH120-160 Issue K2
Page 3 of 9
June 2016