F1300NH55P.pdf 데이터시트 (총 11 페이지) - 파일 다운로드 F1300NH55P 데이타시트 다운로드

No Preview Available !

Date:- 5 Nov, 2014
Data Sheet Issue:- 3
Extra Fast Recovery Diode
Types F1300N#45P to F1300N#55P
Absolute Maximum Ratings
VOLTAGE RATINGS
VRRM
VRSM
VR(d.c.)
Repetitive peak reverse voltage, (note 1)
Non-repetitive peak reverse voltage, (note 1)
Maximum reverse d.c. voltage (note 1)
MAXIMUM
LIMITS
4500-5500
4600-5600
2300-2800
UNITS
V
V
V
OTHER RATINGS (note 6)
IF(AV)M
IF(AV)M
IF(AV)M
IF(RMS)
IF(d.c.)
IFSM
IFSM2
I2t
I2t
Tj op
Tstg
Mean forward current, Tsink=55°C, (note 2)
Mean forward current. Tsink=100°C, (note 2)
Mean forward current. Tsink=100°C, (note 3)
Nominal RMS forward current, Tsink=25°C, (note 2)
D.C. forward current, Tsink=25°C, (note 4)
Peak non-repetitive surge tp=10ms, VRM=60%VRRM, (note 5)
Peak non-repetitive surge tp=10ms, VRM10V, (note 5)
I2t capacity for fusing tp=10ms, VRM=60%VRRM, (note 5)
I2t capacity for fusing tp=10ms, VRM10V, (note 5)
Operating temperature range
Storage temperature range
Notes:-
1) De-rating factor of 0.13% per °C is applicable for Tj below 25°C.
2) Double side cooled, single phase; 50Hz, 180° half-sinewave.
3) Single side cooled, single phase; 50Hz, 180° half-sinewave.
4) Double side cooled.
5) Half-sinewave, 140°C Tj initial.
6) Current (IF) ratings have been calculated using VT0 and rT (see page 2)
MAXIMUM
LIMITS
1346
767
435
2615
2130
20.8
22.9
2.16106
2.62106
-40 to +140
-40 to +140
UNITS
A
A
A
A
A
kA
kA
A2s
A2s
°C
°C
Provisional Rating Report. Types F1300N#45P-55P Issue 3
Page 1
November, 2014

No Preview Available !

Characteristics
Extra Fast Diode Types F1300N#45P-55P
PARAMETER
VFM Maximum peak forward voltage
VT0 Threshold voltage
rT Slope resistance
VT01 Threshold voltage
rT1 Slope resistance
VFRM Maximum forward recovery voltage
IRRM Peak reverse current
Qrr
Qra
Irm
trr
Qrr
Qra
Irm
trr
RthJK
F
Wt
Recovered charge
Recovered charge, 50% Chord
Reverse recovery current
Reverse recovery time, 50% Chord
Recovered charge
Recovered charge, 50% Chord
Reverse recovery current
Reverse recovery time, 50% Chord
Thermal resistance, junction to heatsink
(note 4)
Mounting force
Weight
MIN.
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
19
-
TYP.
-
-
-
-
-
-
-
-
-
-
2150
1010
470
4.3
4680
3680
560
15
-
-
-
510
MAX. TEST CONDITIONS (Note 1)
UNITS
1.75 IFM = 800A
1.95 IFM = 1200A
V
1.569
Over current range 1346 4038A (Note 2)
0.318
V
m
1.539
Over current range 1200 3600A
0.332
V
m
120 di/dt = 1000A/µs, 25ºC
230 di/dt = 1000A/µs
V
40 Rated VRRM
10 Rated VRRM, Tj=25°C
mA
- µC
1300 IFM=1000A, tp=1000µs, di/dt=200A/µs,
- Vr=100V, 50% Chord (note 3)
µC
A
- µs
-
4100
-
-
IFM=1200A, tp=1000µs, di/dt=200A/µs,
Vr=1500V, with 4.5, 1µF snubber
(Note 3)
µC
µC
A
µs
0.024 Double side cooled
K/W
0.048 Anode side cooled
26 (Note 4)
kN
-g
Notes:-
1) Unless otherwise indicated Tj=140°C.
2) VT0 and rT were used to calculate the current ratings illustrated on page one.
3) Figures 3-7 were compiled using these conditions.
4) For clamp forces outside these limits, please consult factory.
Provisional Rating Report. Types F1300N#45P-55P Issue 3
Page 2
November, 2014

No Preview Available !

Extra Fast Diode Types F1300N#45P-55P
Notes on Ratings and Characteristics
1.0 De-rating Factor
A blocking voltage de-rating factor of 0.13% per °C is applicable to this device for Tj below 25°C.
2.0 ABCD Constants
These constants (applicable only over current range of VF characteristic in Figure 1) are the coefficients of
the expression for the forward characteristic given below:
VF A B ln(IF ) C IF D IF
where IF = instantaneous forward current.
3.0 Reverse recovery ratings
(i) Qra is based on 50% Irm chord as shown in Figure below.
(ii) Qrr is based on a 150s integration time.
150s
I.e. Qrr irr.dt
0
(iii)
K Factor t1
t2
Provisional Rating Report. Types F1300N#45P-55P Issue 3
Page 3
November, 2014

No Preview Available !

Extra Fast Diode Types F1300N#45P-55P
4.0 Reverse Recovery Loss
The following procedure is recommended for use where it is necessary to include reverse recovery loss.
From waveforms of recovery current obtained from a high frequency shunt (see Note 1) and reverse
voltage present during recovery, an instantaneous reverse recovery loss waveform must be constructed.
Let the area under this waveform be E joules per pulse. A new sink temperature can then be evaluated
from:
 TSINK TJ (MAX ) E k f RthJK
Where k = 0.2314 (°C/W)/s
E = Area under reverse loss waveform per pulse in joules (W.s.)
f = Rated frequency in Hz at the original sink temperature.
Rth(J-Hs) = d.c. thermal resistance (°C/W)
The total dissipation is now given by:
W(tot) W(original) E f
NOTE 1 - Reverse Recovery Loss by Measurement
This device has a low reverse recovered charge and peak reverse recovery current. When measuring the
charge, care must be taken to ensure that:
(a) AC coupled devices such as current transformers are not affected by prior passage of high
amplitude forward current.
(b) A suitable, polarised, clipping circuit must be connected to the input of the measuring oscilloscope
to avoid overloading the internal amplifiers by the relatively high amplitude forward current signal.
(c) Measurement of reverse recovery waveform should be carried out with an appropriate critically
damped snubber, connected across diode anode to cathode. The formula used for the calculation of this
snubber is shown below:
R2 4 Vr
CS didt
Where: Vr = Commutating source voltage
CS = Snubber capacitance
R = Snubber resistance
Provisional Rating Report. Types F1300N#45P-55P Issue 3
Page 4
November, 2014

No Preview Available !

5.0 Computer Modelling Parameters
5.1 Device Dissipation Calculations
Extra Fast Diode Types F1300N#45P-55P
I AV  VT 0
VT 02 4 ff 2 rT WAV
2 ff 2 rT
Where VT0 = 1.569V, rT = 0.318m
ff = form factor (normally unity for fast diode applications)
WAV
T
Rth
T Tj(MAX ) TK
5.2 Calculation of VF using ABCD Coefficients
The forward characteristic IF Vs VF, on page 6 is represented in two ways;
(i) the well established VT0 and rT tangent used for rating purposes and
(ii) a set of constants A, B, C, and D forming the coefficients of the representative equation for VF in
terms of IF given below:
VF A B ln(IF ) C IF D IF
The constants, derived by curve fitting software, are given in this report for both hot and cold
characteristics. The resulting values for VF agree with the true device characteristic over a current range,
which is limited to that plotted.
25°C Coefficients
140°C Coefficients
A 0.9457614
1.1329943
B 0.0566287
-0.02170949
C 1.6693910-4
7.7818910-5
D 9.15635110-3
0.02495673
Provisional Rating Report. Types F1300N#45P-55P Issue 3
Page 5
November, 2014