E0170YH45C.pdf 데이터시트 (총 11 페이지) - 파일 다운로드 E0170YH45C 데이타시트 다운로드

No Preview Available !

Date:- 8 May, 2014
Data Sheet Issue: A1
Advance Data
High Power Sonic FRD
Type E0170YH45C
Absolute Maximum Ratings
VOLTAGE RATINGS
VRRM
VRSM
VR(d.c.)
Repetitive peak reverse voltage, (note 1)
Non-repetitive peak reverse voltage, (note 1)
Maximum reverse d.c. voltage (note 1)
MAXIMUM
LIMITS
4500
4600
2800
UNITS
V
V
V
OTHER RATINGS (note 6)
IF(AV)M
IF(AV)M
IF(AV)M
IF(RMS)
IF(d.c.)
IFSM
IFSM2
I2t
I2t
Prr
Tj op
Tstg
Mean forward current, Tsink=55°C, (note 2)
Mean forward current. Tsink=100°C, (note 2)
Mean forward current. Tsink=100°C, (note 3)
Nominal RMS forward current, Tsink=25°C, (note 2)
D.C. forward current, Tsink=25°C, (note 4)
Peak non-repetitive surge tp=10ms, VRM=60%VRRM, (note 5)
Peak non-repetitive surge tp=10ms, VRM10V, (note 5)
I2t capacity for fusing tp=10ms, VRM=60%VRRM, (note 5)
I2t capacity for fusing tp=10ms, VRM10V, (note 5)
Maximum non-repetitive peak reverse recovery power, (note 7)
Operating temperature range
Storage temperature range
MAXIMUM
LIMITS
210
135
85
385
340
1390
1530
9.67×103
11.7×103
0.84
-40 to +150
-40 to +150
UNITS
A
A
A
A
A
A
A
A2s
A2s
MW
°C
°C
Notes:-
1) De-rating factor of 0.13% per °C is applicable for Tj below 25°C.
2) Double side cooled, single phase; 50Hz, 180° half-sinewave.
3) Single side cooled, single phase; 50Hz, 180° half-sinewave.
4) Double side cooled.
5) Half-sinewave, 150°C Tj initial.
6) Current (IF) ratings have been calculated using VT0 and rT (see page 2)
7) Tj=Tjop, IF=170A, di/dt=500A/µs Vr=2800V and Ls=200nH. Test circuit and sample waveform are shown in diagram
1. IGBT type T0240NB45E used as switch.
Provisional Data Sheet. Type E0170YH45C Issue A1
Page 1 of 11
May, 2014

No Preview Available !

Characteristics
High Power Sonic FRD Type E0170YH45C
PARAMETER
VFM Maximum peak forward voltage
VT0 Threshold voltage
rT Slope resistance
VT01 Threshold voltage
rT1 Slope resistance
VFRM Maximum forward recovery voltage
IRRM Peak reverse current
Qrr Recovered charge
Qra Recovered charge, 50% Chord
Irm Reverse recovery current
trr Reverse recovery time, 50% Chord
R
thJK
Thermal resistance, junction to heatsink
F Mounting force
Wt Weight
MIN.
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
4.5
TYP.
3.5
-
-
-
-
-
-
-
-
-
280
100
125
1.6
-
-
-
MAX. TEST CONDITIONS (Note 1)
3.7
5.62
2.58
7.17
IFM=170A
IFM=400A
Current range 208 A - 624A (Note 2)
2.37
Current range 170A - 510A
7.81
800 di/dt = 2000A/µs
500 di/dt = 2000A/µs, Tj=25°C
15 Rated VRRM
3 Rated VRRM, Tj=25°C
310
- IFM=170A, tp=1ms, di/dt=300A/µs,
140 Vr=2800V, 50% Chord. (note 3)
-
0.073 Double side cooled
0.146 Single side cooled
6.5 (Note 4)
- 80 -
UNITS
V
V
m
V
m
V
mA
µC
µC
A
µs
K/W
K/W
kN
g
Notes:-
1) Unless otherwise indicated Tj=150°C.
2) VT0 and rT were used to calculate the current ratings illustrated on page one.
3) Figures 3-7 were compiled using these conditions. Test circuit and sample waveform are shown in
diagram 1.
4) For clamp forces outside these limits, please consult factory.
Provisional Data Sheet. Type E0170YH45C Issue A1
Page 2 of 11
May, 2014

No Preview Available !

High Power Sonic FRD Type E0170YH45C
Additional information on Ratings and Characteristics
1.0 De-rating Factor
A blocking voltage de-rating factor of 0.13% per °C is applicable to this device for Tj below 25°C.
2.0 ABCD Constants
These constants (applicable only over current range of VF characteristic in Figure 1) are the coefficients
of the expression for the forward characteristic given below:
VF = A + B ln(I F ) + C I F + D I F
where IF = instantaneous forward current.
3.0 Reverse recovery ratings
Diagram 1 – Reverse Recovery test circuit and sample waveform
LS
IG
D.U.T
(i) Qra is based on 50% Irm chord as shown in Figure below.
(ii) Qrr is based on a 150µs integration time.
150 µs
I.e. Qrr = irr .dt
0
(iii)
K Factor = t1
t2
Provisional Data Sheet. Type E0170YH45C Issue A1
Page 3 of 11
May, 2014