MN101CB6A.pdf 데이터시트 (총 3 페이지) - 파일 다운로드 MN101CB6A 데이타시트 다운로드

No Preview Available !

MN101CB6 Series
Type
Internal ROM type
ROM (byte)
RAM (byte)
Package (Lead-free)
Minimum Instruction
Execution Time
MN101CB6A
32K
1K
MN101CB6D
MN101CB6G
Mask ROM
64K 124K
2K
SSOP032-P-0300B
0.10 µs (at 2.7 V to 3.6 V, 10 MHz)
0.125 µs (at 1.8 V to 3.6 V, 8 MHz)
100 µs (at 1.8 V to 3.6 V, 20 kHz)
MN101CFB6G
FLASH
128K
Interrupts
RESET. Watchdog. External 0 to 4. Timer 0 to 3. Timer 7 (2 systems). Time base. Serial 0 (2 systems). A/D conversion finish
Timer Counter
8-bit timer × 5
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Simple pulse width measurement. Added pulse (2-bit) type PWM
output. Square-wave/PWM output to large current terminal P35 possible
Timer 1 ..................Serial 0 baud rate timer
Timer 2 ..................Square-wave output. Added pulse (2-bit) type PWM output. PWM output. Event count. Simple pulse width
measurement. Serial 0 baud rate timer. Square-wave/PWM output to large current terminal P34 possible
Timer 3 ..................Interval timer
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
16-bit timer × 1
Timer 7 ..................Square-wave output. 16-bit PWM output (cycle/duty continuous variable). Event count. Pulse width measurement.
Input capture. Square-wave/PWM output to large current terminal P33 possible
Time base timer: One-minute count setting
Watchdog timer × 1
Watchdog timer 2 × 1
Serial interface
Synchronous type/UART (full-duplex) × 1: Serial 0
I/O Pins
I/O
17 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)
A/D converter
10-bit × 5 channels (with S/H)
Special Ports
High-current drive port
ROM Correction
Correcting address designation: Up to 3 addresses possible
Gain Amplifier
2 channels
Reference Power Supply Output
1.7 V: Output to REF17 terminal possible. Supply to A/D converter input, A/D converter reference voltage and a reference power for
Double Booster Circuit possible
Double Booster Circuit
Counle boosts REF17 terminal input voltage or Reference Power Supply Output
Reset
Automatic Reset
Internal oscillation
High speed: 8 MHz. Low speed: 20 kHz
MAD00077CEM

No Preview Available !

Pin Assignment
SSOP032-P-0300B
MN101CB6A, MN101CB6D, MN101CB6G, MN101CFB6G
MAD00077CEM

No Preview Available !

Request for your special attention and precautions in using the technical information and
semiconductors described in this book
(1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and
regulations of the exporting country, especially, those with regard to security export control, must be observed.
(2) The technical information described in this book is intended only to show the main characteristics and application circuit examples
of the products. No license is granted in and to any intellectual property right or other right owned by Panasonic Corporation or any
other company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any
other company which may arise as a result of the use of technical information described in this book.
(3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office
equipment, communications equipment, measuring instruments and household appliances).
Consult our sales staff in advance for information on the following applications:
Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support
systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod-
ucts may directly jeopardize life or harm the human body.
Any applications other than the standard applications intended.
(4) The products and product specifications described in this book are subject to change without notice for modification and/or im-
provement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product
Standards in advance to make sure that the latest specifications satisfy your requirements.
(5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions
(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute
maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any
defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure
mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire
or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.
(6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,
thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which
damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.
(7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of our company.
20080805