R-78HB6.5-0.5.pdf 데이터시트 (총 7 페이지) - 파일 다운로드 R-78HB6.5-0.5 데이타시트 다운로드

No Preview Available !

Features
Switching
Regulator
• Efficiency up to 96%, no heatsinks required
• Pin-out compatible with LM78XX linears
• Low profile (L/W/H=11.5 x 8.5 x 17.5mm)
• High input voltage range, up to 72V
• Short circuit protection, thermal shutdown
• Low ripple and noise
• „L“ version with 90° pins
DC/DC Converter
R-78HB-0.5(L)
Description
The R-78HBxx-Series high efficiency, high input voltage switching regulators are ideally suited to replace
78xx linear regulators and are pin compatible. The efficiency of up to 96% means that very little energy
is wasted as heat so there is no need for any heat sinks with their additional space and mounting costs.
An input voltage range of up to 8:1 is unsurpassed by any other converter and allows the full stored
energy utilization of standard and high voltage batteries. The fully protected output is ideal for industrial
applications (especially for industry standard 24VDC bus supplies) and the L-Version with 90° pins
allows direct replacement for laid-flat regulators where component height is at a premium. Low ripple
and noise figures and a short circuit input current of typically only 15mA round off the specifications of
this versatile converter series. Typical applications include telecommunication, automotive, industrial,
aerospace and battery powered applications.
0.5 Amp
SIP3
Single Output
Selection Guide
Part
Number
R-78HB3.3-0.5
R-78HB5.0-0.5
R-78HB6.5-0.5
R-78HB9.0-0.5
R-78HB12-0.5
R-78HB15-0.5
R-78HB24-0.3
Input
Output
Voltage Range Voltage
[VDC] [VDC]
9 - 72 3.3
9 - 72 5.0
9 - 72 6.5
14 - 72 9.0
17 - 72 12
20 - 72 15
36 - 72 24
Output Efficiency
Current
@ min Vin @ max. Vin
[A] [%] [%]
0.5 82 76
0.5 87 81
0.5 91 84
0.5 92 86
0.5 94 89
0.5 95 91
0.3 96 92
Model Numbering
R-78HB__- (L)
Output Voltage
Pinning (1)
Notes:
Output Current
Note1: add suffix „L” for 90° bent pins, e.g. R-78B5.0-1.0L
Specifications (measured @ Ta= 25°C, 10% minimum load, unless otherwise stated)
BASIC CHARACTERISTICS
Parameter
Condition
Min. Typ. Max.
Internal Input Filter
1µF capacitor
Absolute Maximum Input Voltage
75VDC
Quiescent Current
nom. Vin= 48VDC
1mA 5mA
Internal Power Dissipation
0.65W
Minimum Load (2)
2%
Notes:
Note2: Operation under no load will not harm the converter, but specifications may not be met
A minimum load of 10mA is recommended
continued on next page
IEC/EN60950-1 certified
EN55032 compliant
www.recom-power.com
REV.: 5/2019
I-1

No Preview Available !

R-78HBxx-0.5(L)
DC/DC Converter
Specifications (measured @ Ta= 25°C, 10% minimum load, unless otherwise stated)
Series
Parameter
Internal Operating Frequency
Output Ripple and Noise
Absolute Maximum
Capacitive Load
Condition
nom. Vin= 48VDC
20MHz BW (10 - 100% load)
1 second start up, no external components
<1 second start up + diode protection circuit
Min.
120kHz
Typ.
20mVp-p
Max.
800kHz
60mVp-p
100µF
6800µF
Switching Frequency vs. Load
800
400
200
100
50
10
10
24Vout
15Vout
12Vout
9Vout
6.5Vout
5Vout
3.3Vout
50 100 200 300 400 500
Output Current (mA)
Efficiency vs. Vin (full load)
100
90
80
70
60
50
40
30
20
10
0
9
24Vout
15Vout
12Vout
9Vout
6.5Vout
5Vout
3.3Vout
18 27 36 45 54 63 72
Input Voltage [VDC]
Ripple vs. Vin (full load)
50 24Vout
45
15, 12Vout
9Vout
40 6.5Vout
35
5Vout
3.3Vout
30
25
20
15
10
5
0
9 18 27 36 45 54 63 72
Input Voltage [VDC]
www.recom-power.com
continued on next page
REV.: 5/2019
I-2

No Preview Available !

R-78HBxx-0.5(L)
DC/DC Converter
Specifications (measured @ Ta= 25°C, 10% minimum load, unless otherwise stated)
Series
Efficiency vs. Load (max. Vin)
Ripple vs. Load (max. Vin)
100
90
80
70
60
50
40
30
20
10
0
0
24Vout
15Vout
12Vout
9Vout
6.5Vout
5Vout
3.3Vout
10 20 30 40 50 60 70 80 90 100
Output Load [%]
60 24Vout
15, 12Vout
50
9Vout
6.5Vout
5Vout
40 3.3Vout
30
20
10
0
0 10 20 30 40 50 60 70 80 90 100
Output Load [%]
Efficiency vs. Load (min. Vin)
Ripple vs. Load (min. Vin)
100
90
80
70
60
50
40
30
20
10
0
0
24, 15Vout
12Vout
9Vout
6.5Vout
5Vout
3.3Vout
10 20 30 40 50 60 70 80 90 100
Output Load [%]
60 24Vout
15, 12Vout
50
9Vout
6.5Vout
5Vout
40 3.3Vout
30
20
10
0
0 10 20 30 40 50 60 70 80 90 100
Output Load [%]
REGULATIONS
Parameter
Output Accuracy
Line Regulation
Load Regulation
Transient Response (3)
www.recom-power.com
Condition
100% load
low line to high line, 100% load
10% to 100% load
100% <-> 50% load
Notes:
Note3: Measurements are made with a 100µF output capacitor
REV.: 5/2019
Value
±2.0% typ / ±3.0% max.
±0.4% typ. / ±1.0% max.
±0.3% typ. / ±0.6% max.
±75mV typ. / ±100mV max.
I-3

No Preview Available !

R-78HBxx-0.5(L)
DC/DC Converter
Specifications (measured @ Ta= 25°C, 10% minimum load, unless otherwise stated)
Series
PROTECTIONS
Parameter
Short Circuit Protection (SCP)
Short Circuit Input Current
Optional Diode Protection Circuit
Add a blocking diode to Vout if
current can flow backwards into
the output, as this can damage the
converter when it is powered down.
The diode can either be fitted
across the device if the source is
low impedance or fitted in series
with the output (recommended).
Condition
below 100mW
nom. Vin= 24VDC
Optional Protection 1:
+Vin
GND
R-78HBxx-0.5
+Vin +Vout
GND
+Vout
GND
Value
+Vin +VRin -78HBxx-c0o+.5nVotuitnu1ou5sm, Aauttyopm. /+at2Vico5utmreAcomvearxy.
GND
Optional Protection 2:
GND GND
+Vin
R-78HBxx-0.5
+Vin +Vout
+Vout=
GND +Vout - 0.3V
GND GND
Protection Circuit
++VViinn
R-78HBxx-0.5
++VViRnin -78HGNBDxx-0++.5VVoouutt
GND
++VVoouutt=
+Vout - 0.3V
C1
GND
GND
GND GND
To protect the converter during power-up, use C1=3.3µF/100V if Vin>50V
ENVIRONMENTAL
Parameter
Operating Temperature Range
Maximum Case Temperature
Temperature Coefficient
Thermal Impedance
Operating Altitude
Operating Humidity
Pollution Degree
MTBF
Derating Graph
www.recom-power.com
Condition
with derating (see graph)
0.1m/s, vertical
non-condensing
according to MIL-HDBK-217F, G.B.
+25°C
+71°C
100
90
80
70
60
50
40
30
20
10
0
-40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100
Ambient Temperature [°C] 71 85
REV.: 5/2019
Value
-40°C to +85°C
+100°C
±0.015%/K
60K/W
2000m
95% RH max.
PD2
7395 x 103 hours
1242 x 103 hours
I-4

No Preview Available !

R-78HBxx-0.5(L)
DC/DC Converter
Specifications (measured @ Ta= 25°C, 10% minimum load, unless otherwise stated)
Series
SAFETY AND CERTIFICATIONS
Certificate Type (Safety)
Information Technology Equipment, General Requirements for Safety
EAC
RoHs 2+
Report / File Number
1603123
RU-AT.49.09571
Standard
IEC60950-1:2005, 2nd Edition + AM 2:2013
EN60950-1:2006 + AM 2:2013
TP TC 004/2011
RoHS 2011/65/EU + AM2015/863
EMC Compliance
Electromagnetic compatibility of multimedia equipment -
Emission requirements
ESD Electrostatic discharge immunity test
Radiated, radio-frequency, electromagnetic field immunity test
Condition
with external components
Air ±8kV, Contact ±4kV
3V/m
Standard / Criterion
EN55032, Class A
EN55032, Class B
EN61000-4-2, Criteria A
EN61000-4-3, Criteria A
DIMENSION AND PHYSICAL CHARACTERISTICS
Parameter
Material
Package Dimension (LxWxH)
Package Weight
Dimension Drawing (mm)
Type
case
potting
with suffix „L” bent pins
Value
non-conductive black plastic, (UL94 V-0)
silicone, (UL94 V-0)
11.5 x 8.5 x 17.5mm
4g typ.
11.5
embossed logo
8.5
Marking
embossed logo
11.5 8.5
Marking
Pin Connections
Pin # Single
1 +Vin
2 GND
3 +Vout
Tolerance: xx.x= ±0.5mm
xx.xx= ±0.25mm
0.70+0.10/-0.05
Bottom View
123
3.21 5.08
0.25±0.05
0.70+0.10/-0.05
Recommended Footprint Details
123
Top View
2.54
Bottom View
123
5.08
www.recom-power.com
REV.: 5/2019
6.10
Recommended Footprint Details
Top View
1 23
2.54
I-5