TPSMA36A.pdf 데이터시트 (총 5 페이지) - 파일 다운로드 TPSMA36A 데이타시트 다운로드

No Preview Available !

www.vishay.com
TPSMA6.8A thru TPSMA43A
Vishay General Semiconductor
Surface Mount PAR® Transient Voltage Suppressors
High Temperature Stability and High Reliability Conditions
SMA (DO-214AC)
PRIMARY CHARACTERISTICS
VWM
VBR
PPPM
PD
IFSM
TJ max.
Polarity
5.8 V to 36.8 V
6.8 V to 43 V
400 W
1.0 W
40 A
185 °C
Uni-directional
Package
SMA (DO-214AC)
TYPICAL APPLICATIONS
Use in sensitive electronics protection against voltage
transients induced by inductive load switching and lightning
on ICs, MOSFET, signal lines of sensor units for consumer,
computer, industrial, automotive, and telecommunication.
FEATURES
• Junction passivation optimized design
passivated anisotropic rectifier technology
• TJ = 185 °C capability suitable for high reliability
and automotive requirement
• Available in uni-directional polarity only
Available
• 400 W peak pulse power capability with a 10/1000 μs
waveform, repetitive rate (duty cycle): 0.01 %
• Excellent clamping capability
• Very fast response time
• Low incremental surge resistance
• Meets MSL level 1, per J-STD-020, LF maximum peak of
260 °C
• AEC-Q101 qualified available
- Automotive ordering code: base P/NHE3 or P/NHM3
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
MECHANICAL DATA
Case: SMA (DO-214AC)
Molding compound meets UL 94 V-0 flammability rating
Base P/NHE3_X - RoHS-compliant and AEC-Q101 qualified
Base P/NHM3_X - halogen-free, RoHS-compliant, and
AEC-Q101 qualified
(“_X” denotes revision code e.g. A, B, ...)
Terminals: matte tin plated leads, solderable per
J-STD-002 and JESD 22-B102
HE3 and HM3 suffix meets JESD 201 class 2 whisker test
Polarity: color band denotes cathode end
MAXIMUM RATINGS (TA = 25 °C unless otherwise noted)
PARAMETER
SYMBOL
VALUE
Peak power dissipation with a 10/1000 μs waveform (1)(2) (fig. 3)
Peak power pulse current with a 10/1000 μs waveform (1) (fig. 1)
Power dissipation at TA = 25 °C (4)
Peak forward surge current 8.3 ms single half sine-wave (3)
Maximum instantaneous forward voltage at 25 A (3)
PPPM
IPPM
PD
IFSM
VF
400
See next table
1.0
40
3.5
Operating junction and storage temperature range
TJ, TSTG
-65 to +185
Notes
(1) Non-repetitive current pulse, per fig. 3 and derated above TA = 25 °C per fig. 2
(2) Mounted on PCB with 0.2" x 0.2" (5.0 mm x 5.0 mm) copper pads attached to each terminal
(3) Measured on 8.3 ms single half sine-wave or equivalent square wave, duty cycle = 4 pulses per minutes maximum
(4) Mounted on minimum recommended pad layout
UNIT
W
A
W
A
V
°C
Revision: 11-Jul-17
1 Document Number: 88405
For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

No Preview Available !

www.vishay.com
TPSMA6.8A thru TPSMA43A
Vishay General Semiconductor
ELECTRICAL CHARACTERISTICS (TA = 25 °C unless otherwise noted)
DEVICE TYPE
DEVICE
MARKING
CODE
BREAKDOWN
VOLTAGE
VBR (1) AT IT
(V)
MIN.
MAX.
TEST
CURRENT
IT
(mA)
STAND-
OFF
VOLTAGE
VWM
(V)
MAXIMUM
REVERSE
LEAKAGE
AT VWM
IR (μA)
TJ = 150 °C
MAXIMUM
REVERSE
LEAKAGE AT
VWM
ID (μA)
MAXIMUM
PEAK
PULSE
SURGE
CURRENT
IPPM (2)
(A)
MAXIMUM
CLAMPING
VOLTAGE
AT IPPM
VC (V)
TPSMA6.8A AEP 6.45 7.14 10 5.80 300
TPSMA7.5A AGP 7.13 7.88 10 6.40 150
1000
500
38.1 10.5
35.4 11.3
TPSMA8.2A AKP 7.79 8.61 10 7.02 50
200 33.1 12.1
TPSMA9.1A AMP 8.65 9.55 1.0 7.78 10
TPSMA10A
APP 9.50 10.50 1.0 8.65 5.0
50 29.9 13.0
20 27.6 14.5
TPSMA11A
ARP
10.50
11.60
1.0
9.40
1.0
5.0 25.6 15.6
TPSMA12A
TPSMA13A
ATP
11.40
12.60
1.0
10.20
1.0
AVP
12.40
13.70
1.0
11.10
1.0
5.0 24.0 16.7
5.0 22.0 18.2
TPSMA15A
AXP
14.30
15.80
1.0
12.80
1.0
5.0 18.9 21.2
TPSMA16A
TPSMA18A
AZP
15.20
16.80
1.0
13.60
1.0
BEP
17.10
18.90
1.0
15.30
1.0
5.0 17.8 22.0
5.0 15.9 25.5
TPSMA20A
BGP
19.00
21.00
1.0
17.10
1.0
5.0 14.4 27.7
TPSMA22A
TPSMA24A
BKP
20.90
23.10
1.0
18.80
1.0
BMP
22.80
25.20
1.0
20.50
1.0
5.0 13.1 30.6
5.0 12.0 33.2
TPSMA27A
BPP
25.70
28.40
1.0
23.10
1.0
5.0 10.7 37.5
TPSMA30A
BRP
28.50
31.50
1.0
25.60
1.0
5.0
9.7 41.4
TPSMA33A
BTP
31.40
34.70
1.0
28.20
1.0
5.0
8.8 45.7
TPSMA36A
BVP
34.20
37.80
1.0
30.80
1.0
5.0
8.0 49.9
TPSMA39A
BXP
37.10
41.00
1.0
33.30
1.0
5.0
7.4 53.9
TPSMA43A
BZP
40.90
45.20
1.0
36.80
1.0
5.0
6.7 59.3
Notes
(1) VBR measured after IT applied for 300 μs, IT = square wave pulse or equivalent
(2) Surge current waveform per fig. 3 and derated per fig. 2
(3) All terms and symbols are consistent with ANSI/IEEE C62.35
ORDERING INFORMATION (Example)
PREFERRED P/N
UNIT WEIGHT (g)
TPSMA6.8AHE3_B/H (1)
0.064
TPSMA6.8AHE3_B/I (1)
0.064
TPSMA6.8AHM3_B/H (1)
0.064
TPSMA6.8AHM3_B/I (1)
0.064
PREFERRED PACKAGE CODE
H
I
H
I
Note
(1) AEC-Q101 qualified
BASE QUANTITY
1800
7500
1800
7500
DELIVERY MODE
7" diameter plastic tape and reel
13" diameter plastic tape and reel
7" diameter plastic tape and reel
13" diameter plastic tape and reel
Revision: 11-Jul-17
2 Document Number: 88405
For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

No Preview Available !

www.vishay.com
TPSMA6.8A thru TPSMA43A
Vishay General Semiconductor
RATINGS AND CHARACTERISTICS CURVES (TA = 25 °C unless otherwise noted)
100
Non-Repetitive Pulse
Waveform shown in Fig. 3
TA = 25 °C
10
1.0
0.1
0.1 µs
0.2 x 0.2" (5.0 x 5.0 mm)
Copper Pad Areas
1.0 µs
10 µs 100 µs 1.0 ms
td - Pulse Width (s)
10 ms
Fig. 1 - Peak Pulse Power Rating Curve
10 000
1000
VR measured
at Zero Bias
100
10
1
VR measured at
Stand-Off, VWM
TJ = 25 °C
f = 1.0 MHz
Vsig = 50 mVp-p
10
VBR - Breakdown Voltage (V)
100
Fig. 4 - Typical Junction Capacitance
100 200
TJ = TJ max.
8.3 ms Single Half Sine-Wave
75 100
50
50
25
0
0 50 100 150 200
TJ - Initial Temperature (°C)
Fig. 2 - Pulse Power or Current vs. Initial Junction Temperature
150
tr = 10 µs
TJ = 25 °C
Pulse Width (td)
is defined as the Point
Peak Value
where the Peak Current
100 IPPM
decays to 50 % of IPPM
Half Value - IPP
IPPM
2
50
10/1000 µs Waveform
as defined by R.E.A.
td 0
0
td
1.0
2.0
t - Time (ms)
3.0
Fig. 3 - Pulse Waveform
4.0
10
1
5 10
50
Number of Cycles at 60 Hz
100
Fig. 5 - Maximum Non-Repetitive Peak Forward Surge Current
Revision: 11-Jul-17
3 Document Number: 88405
For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

No Preview Available !

www.vishay.com
TPSMA6.8A thru TPSMA43A
Vishay General Semiconductor
PACKAGE OUTLINE DIMENSIONS in inches (millimeters)
SMA (DO-214AC)
Cathode Band
Mounting Pad Layout
0.065 (1.65)
0.049 (1.25)
0.110 (2.79)
0.100 (2.54)
0.066 (1.68)
MIN.
0.074 (1.88)
MAX.
0.090 (2.29)
0.078 (1.98)
0.060 (1.52)
0.030 (0.76)
0.177 (4.50)
0.157 (3.99)
0.012 (0.305)
0.006 (0.152)
0.060 (1.52)
MIN.
0.208 (5.28)
REF.
0.008 (0.203)
0 (0)
0.208 (5.28)
0.194 (4.93)
Revision: 11-Jul-17
4 Document Number: 88405
For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

No Preview Available !

www.vishay.com
Legal Disclaimer Notice
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of
typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding
statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a
particular product with the properties described in the product specification is suitable for use in a particular application.
Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over
time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.
Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for
such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document
or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
Revision: 08-Feb-17
1
Document Number: 91000