S-24C512C.pdf 데이터시트 (총 30 페이지) - 파일 다운로드 S-24C512C 데이타시트 다운로드

No Preview Available !

S-24C512C
www.ablicinc.com
© ABLIC Inc., 2010-2013
2-WIRE SERIAL E2PROM
Rev.2.0_03_S
The S-24C512C is a 2-wire, low current consumption and wide range operation serial E2PROM. The S-24C512C has the
capacity of 512 K-bit, and the organization is 65536 words 8-bit. Page write and sequential read are available.
Features
Operating voltage range
Read:
1.6 V to 5.5 V
Write:
1.7 V to 5.5 V
Page write:
128 bytes / page
Sequential read
Operation frequency:
Write time:
1.0 MHz (VCC = 2.5 V to 5.5 V)
400 kHz (VCC = 1.6 V to 2.5 V)
5.0 ms max.
Noise suppression:
Schmitt trigger and noise filter on input pins (SCL, SDA)
Write protect function during the low power supply voltage
Endurance:
106 cycles / unit*1 (Ta = 25°C)
Data retention:
100 years (Ta = 25°C)
Memory capacity:
512 K-bit
Write protect:
100%
Initial shipment data:
FFh
Lead-free (Sn 100%), halogen-free*2
*1. For each unit (unit: the 4 bytes with the same address of W15 to W2)
*2. Refer to “Product Name Structure” for details.
Packages
8-Pin SOP (JEDEC)
8-Pin TSSOP
Caution
This product is intended to use in general electronic devices such as consumer electronics,
office equipment, and communications devices. Before using the product in medical equipment
or automobile equipment including car audio, keyless entry and engine control unit, contact to
ABLIC Inc. is indispensable.
1

No Preview Available !

2-WIRE SERIAL E2PROM
S-24C512C
Pin Configurations
1. 8-Pin SOP (JEDEC)
8-Pin SOP (JEDEC)
Top view
18
27
36
45
Figure 1
S-24C512CI-J8T1U4
Rev.2.0_03_S
Table 1
Pin No
Symbol
Description
1 A0 Slave address input
2 A1 Slave address input
3 A2 Slave address input
4
GND
Ground
5
SDA*1
Serial data I/O
6
SCL*1
Serial clock input
Write protect input
7
WP Connected to VCC:
Protection valid
Open or connected to GND: Protection invalid
8
VCC
Power supply
*1. Do not use it in high impedance.
2. 8-Pin TSSOP
8-Pin TSSOP
Top view
18
27
36
45
Figure 2
S-24C512CI-T8T1U4
Table 2
Pin No
Symbol
Description
1 A0 Slave address input
2 A1 Slave address input
3 A2 Slave address input
4
GND
Ground
5
SDA*1
Serial data I/O
6
SCL*1
Serial clock input
Write protect input
7
WP Connected to VCC:
Protection valid
Open or connected to GND: Protection invalid
8
VCC
Power supply
*1. Do not use it in high impedance.
Remark Refer to the “Package drawings” for the details.
2

No Preview Available !

Rev.2.0_03_S
Block Diagram
SCL
SDA
A2
A1
A0
Start / Stop
Detector
LOAD
Device Address
Comparator
Serial Clock
Controller
COMP
LOAD INC
R/W
Address
Counter
Y Decoder
DIN
DOUT
Figure 3
2-WIRE SERIAL E2PROM
S-24C512C
VCC
WP
GND
Voltage Detector
High-Voltage Generator
Data Register
X Decoder Memory Cell Array
Selector
Data Output
ACK Output
Controller
3

No Preview Available !

2-WIRE SERIAL E2PROM
S-24C512C
Rev.2.0_03_S
Absolute Maximum Ratings
Table 3
Item
Symbol
Absolute Maximum Ratings
Unit
Power supply voltage
VCC
0.3 to 6.5
V
Input voltage
VIN
0.3 to 6.5
V
Output voltage
VOUT
0.3 to 6.5
V
Operation ambient temperature
Topr
40 to 85
°C
Storage temperature
Tstg
65 to 150
°C
Caution The absolute maximum ratings are rated values exceeding which the product could suffer
physical damage. These values must therefore not be exceeded under any conditions.
Recommended Operating Conditions
Table 4
Item
Power supply voltage
High level input voltage
Low level input voltage
Symbol
Condition
VCC
Read Operation
Write Operation
VIH
VCC = 1.8 V to 5.5 V
VCC = 1.6 V to 1.8 V
VIL
VCC = 1.8 V to 5.5 V
VCC = 1.6 V to 1.8 V
Ta = 40°C to 85°C
Min. Max.
1.6 5.5
1.7 5.5
0.7 VCC
0.8 VCC
0.3
0.3
5.5
5.5
0.3 VCC
0.2 VCC
Unit
V
V
V
V
V
V
Pin Capacitance
Item
Input capacitance
I/O capacitance
Table 5
Symbol
CIN
CI / O
Condition
VIN = 0 V (SCL, A0, A1, A2, WP)
VI / O = 0 V (SDA)
(Ta = 25°C, f = 1.0 MHz, VCC = 5.0 V)
Min.
Max.
Unit
10 pF
10 pF
Endurance
Table 6
Item Symbol Operation Ambient Temperature
Endurance
NW
Ta = 25°C
*1. For each unit (unit: the 4 bytes with the same address of W15 to W2)
Min.
106
Max.
Unit
cycles / unit*1
Data Retention
Item
Data retention
Symbol
Table 7
Operation Ambient Temperature
Ta = 25°C
Min.
100
Max.
Unit
year
4

No Preview Available !

Rev.2.0_03_S
2-WIRE SERIAL E2PROM
S-24C512C
DC Electrical Characteristics
Item
Current consumption (READ)
Symbol
ICC1
Table 8
Condition
Ta = 40°C to 85°C
VCC = 2.5 V to 5.5 V
fSCL = 1.0 MHz
Min. Max.
VCC = 1.6 V to 2.5 V
fSCL = 400 kHz
Min. Max.
2.0 1.5
Unit
mA
Item
Current consumption (WRITE)
Symbol
ICC2
Table 9
Condition
Ta = 40°C to 85°C
VCC = 2.5 V to 5.5 V
fSCL = 1.0 MHz
Min. Max.
VCC = 1.7 V to 2.5 V
fSCL = 400 kHz
Min. Max.
4.0 4.0
Unit
mA
Table 10
Item
Symbol
Condition
Standby current consumption ISB
Input leakage current 1
ILI1
Input leakage current 2
ILI2
Output leakage current
Input current 1
Input current 2
Input Impedance 1
Input Impedance 2
ILO
IIL
IIH
ZIL
ZIH
Low level output voltage
VOL
VIN = VCC or GND
SCL, SDA,
VIN = GND to VCC
A0, A1, A2
VIN > 0.7 VCC
At standby mode
SDA
VOUT = GND to VCC
WP
VIN < 0.3 VCC
WP
VIN > 0.7 VCC
WP
VIN = 0.3 VCC
WP
VIN = 0.7 VCC
IOL = 3.2 mA
IOL = 1.5 mA
IOL = 0.7 mA
Ta = 40°C to 85°C
VCC = 2.5 V to 5.5 V
Min. Max.
VCC = 1.6 V to 2.5 V
Min. Max.
8.0 4.0
1.0 1.0
 1.0
 1.0
1.0 1.0
50.0 50.0
2.0 2.0
30 30
500 500
0.4
0.3 0.3
0.2 0.2
Unit
A
A
A
A
A
A
k
k
V
V
V
5