P3002CAL.pdf 데이터시트 (총 3 페이지) - 파일 다운로드 P3002CAL 데이타시트 다운로드

No Preview Available !

Compak TwinCHIPSIDACtor® Device
RoHS
The modified DO-214AA SIDACtor devices provide low-cost, longitudinal protection.
1
(T)
3
(R)
2
(G)
SIDACtor devices enable equipment to comply with various regulatory requirements
including GR 1089, ITU K.20, K.21, and K.45, IEC 60950, UL 60950, and TIA-968-A
(formerly known as FCC Part 68).
Electrical Parameters
Part
Number
P1402C_L
P1602C_L
P2202C_L
P2702C_L
P3002C_L
P3602C_L
P4202C_L
P4802C_L
P6002C_L
VDRM
Volts
VS
Volts
Pins1-2, 2-3
58 77
65 95
90 130
120 160
140 180
170 220
190 250
220 300
275 350
VDRM
Volts
VS
Volts
Pins 1-3
116 154
130 190
180 260
240 320
280 360
340 440
380 500
440 600
550 700
VT
Volts
4
4
4
4
4
4
4
4
4
IDRM
µAmps
5
5
5
5
5
5
5
5
5
IS
mAmps
800
800
800
800
800
800
800
800
800
IT
Amps
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
IH
mAmps
120
120
120
120
120
120
120
120
120
* “L” in part number indicates RoHS compliance. For non-RoHS compliant device, delete “L” from part number.
For surge ratings, see table below.
General Notes:
• All measurements are made at an ambient temperature of 25 °C. IPP applies to -40 °C through +85 °C temperature range.
• IPP is a repetitive surge rating and is guaranteed for the life of the product.
• Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities.
• VDRM is measured at IDRM.
• VS is measured at 100 V/µs.
• Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request.
• UL 60950 creepage requirements must be considered.
Surge Ratings in Amps
IPP
0.2x310 * 2x10 * 8x20 * 10x160 * 10x560 * 5x320 * 10x360 * 10x1000 * 5x310 *
ITSM
0.5x700 ** 2x10 ** 1.2x50 ** 10x160 ** 10x560 ** 9x720 ** 10x360 ** 10x1000 ** 10x700 ** 50 / 60 Hz
di/dt
Amps Amps Amps
Amps
Amps
Amps
Amps
Amps
Amps Amps Amps/µs
A 20
150 150
90
50 75 75
45
75 20 500
B 25
250 250
150
100 100
125
80
100 30 500
* Current waveform in µs
** Voltage waveform in µs
Note: Contact factory for release date of Series B.
Telecom Design Guide • © 2006 Littelfuse
3 - 13
www.littelfuse.com

No Preview Available !

Compak TwinCHIP™ SIDACtor® Device
Thermal Considerations
Package
Modified DO-214AA
Pin 3
Symbol
TJ
TS
RθJA
Pin 1
Pin 2
Parameter
Operating Junction Temperature Range
Storage Temperature Range
Thermal Resistance: Junction to Ambient
Value
-40 to +150
-65 to +150
85
Unit
°C
°C
°C/W
Capacitance Values
pF
Pin 1-2 / 3-2
Tip-Ground, Ring-Ground
Part Number *
MIN
MAX
P1402C[A/B]L
30
55
P1602C[A/B]L
30
55
P2202C[A/B]L
25
50
P2702C[A/B]L
25
45
P3002C[A/B]L
20
40
P3602C[A/B]L
20
40
P4202C[A/B]L
20
40
P4802C[A/B]L
20
35
P6002C[A/B]L
15
35
* [A/B] in part number indicates that values are for both A and B surge ratings.
Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias.
pF
Pin 1-3
Tip-Ring
MIN MAX
15 35
15 30
15 30
10 25
10 25
10 25
10 25
10 20
10 20
www.littelfuse.com
3 - 14
© 2006 Littelfuse • Telecom Design Guide

No Preview Available !

Compak TwinCHIP™ SIDACtor® Device
+I
IT
IS
IH
IDRM
-V
+V
VT VDRM
VS
V-I Characteristics
-I
tr = rise time to peak value
100
Peak td = decay time to half value
Value
Waveform = tr x td
50 Half Value
0
0 tr
td
t – Time (µs)
tr x td Pulse Waveform
14
12
10
8
6
4 25 ˚C
2
0
-4
-6
-8
-40 -20 0 20 40 60 80 100 120 140 160
Junction Temperature (TJ) – ˚C
Normalized VS Change versus Junction Temperature
2.0
1.8
1.6
1.4
1.2 25 ˚C
1.0
0.8
0.6
0.4
-40 -20 0 20 40 60 80 100 120 140 160
Case Temperature (TC) – ˚C
Normalized DC Holding Current versus Case Temperature
Telecom Design Guide • © 2006 Littelfuse
3 - 15
www.littelfuse.com