G1135A.pdf 데이터시트 (총 11 페이지) - 파일 다운로드 G1135A 데이타시트 다운로드

No Preview Available !

G1135A
High Precision CC/CV Primary Side PWM Controller
ANALOG PWM IC
1. General Description
G1135A is a high performance offline PWM
Power switch for low power AC/DC charger and
adaptor applications.
It operates in primary-side sensing and
regulation. Consequently, Opto-coupler and
TL431 could be eliminated.
Proprietary Constant Voltage (CV) and Constant
Current (CC) control is integrated as shown In
the Fig.1.In CC control,the current and output
power setting can be adjusted externally by the
sense resistor RS at CS pin. In CV control,
multi-mode operations are utilized to achieve
high performance and high efficiency.
In addition,good load regulation is achieved by
the built-in cable drop compensation. Device
operates in PFM in CC mode as well at large load
condition and it operates in PWM with frequency
reduction at light/medium load.
G1135A offers power on soft start control and
protection coverage with auto-recovery features
including Cycle-by-Cycle current limiting,VDD
OVP,VDD clamp and UVLO. Excellent EMI
performance is achieved with frequency jitter
technique.
Features
5% Constant Voltage Regulation, 5%
Constant Current Regulation at
Universal AC input
Primary-side Sensing and Regulation
Without TL431 and Opto-coupler
Built-in High-Voltage Power MOS
Power on Soft-start
Internal Cable Compensation
Built-in Leading Edge Blanking (LEB)
Cycle-by-Cycle Current Limiting
VDD Under Voltage Lockout with
Hysteresis (UVLO)
Programmable CV and CC Regulation
Adjustable Constant Current and
Output Power Setting
Built-in Secondary Constant Current
Control with Primary Side Feedback
Built-in adaptive current peak regulation
Built-in Primary winding inductance
compensation
Program cable drop compensation
VDD OVP and VDD Clamp
5000V HBM ESD
Pb-free DIP-8L
Fig.1. Typical CC/CV Curve
Applications
Cell Phone /Digital Cameras Charger
Small Power Adaptor
Auxiliary Power for PC, TV etc.
Linear Regulator/RCC Replacement
Global Semiconductor Co., LTD.
1 of 11

No Preview Available !

G1135A
High Precision CC/CV Primary Side PWM Controller
2. Products Information
2.1 Pin configuration
VDD
COMP
INV
CS
GND
GND
DRAIN
DRAIN
Pin Configuration: G1135A
Pin Name
VDD
COMP
INV
CS
DRAIN
GND
I/O Description
P Power Supply
I Loop Compensation for CV Stability
The Voltage feedback from auxiliary winding.
Connected to resistor
I
divider from auxiliary winding reflecting output
voltage. PWM duty
cycle is determined by EA output and current
sense signal at pin 3
I Current sense input. Connected to MOSFET
current sensing resistor node
O HV MOSFET Drain Pin. The Drain pin is
connected to the primary
lead of the transformer
P Ground
Rev. 1.1
2 of 11

No Preview Available !

G1135A
High Precision CC/CV Primary Side PWM Controller
2.2 Block diagram
2 .3 Output Power Table
Product
G1135A
90~265VAC
Adapter1
12W
Notes:1.Maximum practical continuous power in an Adapter design with sufficient drain pattern as a
heat sink, at 50ambient. Higher output power is possible with extra added heat sink or air
circulation to reduce thermal resistance.
www.globalsemi-group.com
3 of 11

No Preview Available !

G1135A
High Precision CC/CV Primary Side PWM Controller
3. Absolute Maximum Ratings
Description
VDD Voltage
HV MOSFET Drain Voltage
VDD Zener Clamp Continuous Current
COMP Voltage
CS Input Voltage
INV Input Voltage
HBM ESD
MM ESD
Min/Max Operating Junction Temperature
TJ
Min/Max Storage Temperature Tstg
Lead Temperature (Soldering, 10secs)
Operating Junction Temperature Range
Absolute Maximum Ratings
-0.3 to VDD_clamp
-0.3 to BVdss
10 mA
-0.3 to 7V
-0.3 to 7V
-0.3 to 7V
3000V
500V
-20 to 150
-55 to 150
220
-55 to + 150
Note: Stress beyond those listed under “absolute maximum ratings” may cause permanent damage to
the device. Exposure to absolute maximum-rated conditions for extended periods may affect device
reliability
Rev. 1.1
4 of 11

No Preview Available !

G1135A
High Precision CC/CV Primary Side PWM Controller
4. Typical Application
5. Electrical Characteristics
(TA = 25, VDD=16V, unless otherwise noted)
Symbol
Parameter
Test Conditions
Supply Voltage
IDD_ST
Standby current
VDD=13V
IDD_OP
UVLO(ON)
UVLO(OFF)
Operation Current
VDD Under
Voltage
Lockout Enter
VDD Under
Voltage
Lockout Exit
INV=2V,CS=0V,
VDD =20V
VDD falling
VDD rising
OVP
Over voltage
protection voltage
V_clamp
Maximum VDD
operation voltage
Current Sense
Ramp up VDD until
gate clock is off
IDD=10mA
TLEB
Vth_oc
Td_oc
LEB time
Over current
threshold
OCP Propagation
delay
ZSENSE_IN
Input Impedance
T_ss
Soft start time
CV Section
Freq_Nom
System Nominal
switch frequency
Min Typ Max Unit
5 10
2.5 3.5
uA
mA
7.5 8.5 10
V
13.5 14.5 16.0
V
27.5 29.5 31
30.5 32.5 34.5
V
V
540
880 910 940
150
50
10
ns
mV
nS
K
mS
60 KHz
www.globalsemi-group.com
5 of 11