OCP8135A.pdf 데이터시트 (총 3 페이지) - 파일 다운로드 OCP8135A 데이타시트 다운로드

No Preview Available !

OCP8135A
High Efficiency Synchronous Boost Converter
For 1.5A WLED Flash
General Description
The OCP8135A is a 2MHz fixed frequency
synchronous boost converter, optimized for maximum
1.5A camera flash application and maximum 800mA
movie mode applications using high-current white
LEDs in all single cell Li-ion powered products. An
adaptive regulation method ensures the current for
each LED remains in regulation and maximizes
efficiency.
Two simple logic control inputs (ENM and ENF)
enable and disable flash and movie mode operation of
the OCP8135A. Movie-mode and Flash-mode current
levels are independently fixed by two separate
resistors (RM and RF). For Flash mode, a default timer
can be used either to terminate a flash event or as a
safety flash timer. One or two LEDs can be connected
to the OCP8135A; in the case of two LEDs the output
current is matched between each diode.
Thermal regulation is integrated in Flash mode to
limit the ICs temperature and continuously provide the
maximum allowed output current.
The OCP8135A contain a thermal management
system to protect the device; a internal over-voltage
protection (OVP) circuitry prevents damaged to the
OCP8135A from open LED or open circuit conditions;
and a cycle-by-cycle current limit prevents damage to
the OCP8135A. Built-in circuitry prevents excessive
inrush current during start-up. The shutdown feature
reduces quiescent current to less than 1.0μA.
The 2MHz switching frequency allow for the use of
tiny, low profile (1uH or 2.2uH) inductors and 10uF
ceramic capacitors. The device is available in 14-pin
2mmX3mm DFN package and is rated over the -40°C
to 85°C.
Features
Input Voltage Range: 2.7V to 5.3 V
Dual Channel Output
Drives up to 1.5A Regulated Output Current
(0.75A per Channel)
High Efficiency PWM Boost Converter
2.0MHz Fixed Switching Frequency
Up to 97% Efficiency with Small Inductor 1uH
Integrated Soft-Start Eliminates Inrush Current
Under Voltage Lock-Out
Over-Temperature Protection
Thermal Sensing and Current Scale Back
Over Voltage (Open LED) Protection
LED Short Circuit Protection
800mS Flash Timer Control
Cycle by Cycle Current Limit
Separate Hardware Flash and Movie Enable
Independently Set Flash/Movie Currents
Flash Mode Current Up to 1.5A
Movie Mode Current Up to 800mA
Two Resistors Set Flash and Movie Current
Independently
Small Solution Size
Less than 1uA Shutdown Current
RoHS and Green Compliant
14-pin, 2mm X 3mm DFN Packages
-40to +85 Temperature Range
Applications
Camera Flashes and Movies
Cell Phones or Smart Phones
PDAs and Digital Camera
White LED Biasing
Mobil Handsets
Tablet PCs and Laptops/Netbooks
Camcorder Video Light (Movie Light)
Page1 - 3
Ver. 1.3 Feb .27, 2018
源于灿瑞 磁传天下

No Preview Available !

Pin Configuration
DFN2030-14L (Top View)
OCP8135A
Figure 1, Pin Assignments of OCP8135A
Pin
Name
Pin No.
DFN2030-
14L
I/O
Pin Function
Movie mode current setting input. A 71kΩ resistor from RM to GND sets the
RM
1
I/O
desired movie current available at LED1 and LED2 up to 200mA total current.
Each LED1 and LED2 channel will conduct 50% of the maximum
programmed current.
Flash mode current setting input. A 11.5kΩ resistor from RF to GND sets the
RF
2
I/O
maximum flash current available at LED1 and LED2 up to 1.5A total current.
Each LED1 and LED2 channel will conduct 50% of the maximum
programmed current.
AGND
3
P Analog Ground and flash ground.
VIN
4
P
Power input. Connect VIN to the input power supply voltage. Connect a 10uF
ceramic capacitor from VIN to GND as close as possible to OCP8135A.
SW 5 O Drain connection for internal NMOS and Synchronous PMOS Switches.
SW 6 O Drain connection for internal NMOS and Synchronous PMOS Switches.
PGND
7
P
Boost power ground pin. Connect PGND to GND and AGND at a single point
as close as possible to OCP8135A.
Power output of the boost converter. Connect a 10uF ceramic capacitor from
OUT
8, 9
O OUT to PGND as close as possible to the OCP8135A. Connect OUT to the
anodes of the Flash LEDs.
ENF
10
Flash mode enable pin. A low to high transition on the ENF pin initiates flash
mode current level set by RF resistor. ENF is a active high control input with a
I
internal 300kΩ resistance to GND. No matter the status of ENM, only When
ENF = 1, Flash mode is in active and the flashing current is equal to IRF *D ,
D is the duty cycle of PWM signal at ENM pin ,the frequency of PWM is larger
than 15KHz
Movie/Torch mode enable pin and PWM Dimming Pin of Flash Mode. ENM is
a active high control input with a internal 300kΩ resistance to GND. In Flash
ENM
11
Mode, the PWM signal at ENM pin is the flashing current dimming control.
I
When ENF = 0and the timer of ENM = 1is not less than 5ms, Movie/Torch
mode will be in active. The LED current should be equal to IRM * D,D is the
duty cycle of PWM signal at ENM pin . This PWM signal is sent to ENM pin
after the first pulse which 1level time is more than 5ms. When ENF = 0and
the of ENM = 0is not less than 5ms, the chip will enter into shutdown mode.
Channel 1 flash LED pin. Connect cathode of a flash LED to LED1. For a
LED1
12
O
single flash LED, connect LED1 and LED2 together. For two flash LEDs,
each output will conduct of 50% of the total flash current. LED1 is high
impedance during shutdown.
AGND
13
P Analog Ground and flash ground.
Channel 2 flash LED pin. Connect cathode of a flash LED to LED2. For a
LED2
14
O
single flash LED, connect LED1 and LED2 together. For two flash LEDs,
each output will conduct of 50% of the total flash current. LED2 is high
impedance during shutdown.
GND EP P Exposed paddle (bottom). Connect EP to PGND as close as possible.
Page2 - 3
Ver. 1.3 Feb .27, 2018
源于灿瑞 磁传天下

No Preview Available !

Typical Application Circuit
OCP8135A
Figure 2, Typical Application Circuit of OCP8135A
Ordering Information
Part Number
OCP8135AVAD
Driver
Capability
1.5A or
2*0.75A
Package Type
DFN2030-14L
Package Qty
Temperature
7-in reel3000pcs/reel -4085
Eco
Plan
Green
Lead
NIPDAU
注:想进一步了解产品咨询,请直接点击申请样品。我们会第一时间联系您!谢谢!
Page3 - 3
Ver. 1.3 Feb .27, 2018
源于灿瑞 磁传天下