OCXO-131-1006.pdf 데이터시트 (총 3 페이지) - 파일 다운로드 OCXO-131-1006 데이타시트 다운로드

No Preview Available !

NIADHDWHNF(OCXO 131-1006)
www.isotemp.com www.taitien.com
CRYSTAL OSCILLATOR SPECIFICATION
This specification defines the operating characteristics of an ovenized crystal
oscillator. Long term stability is assured through use of premium components.
REV.
DESCRIPTION OF REVISION
-
- Updated to actual performance
A 4.2. was 300 mA
DWN. BY APV. BY
DATE
TST TST 12-28-2008
SZ TST 01-17-2011
TST TST 08-11-2011
1. OUTPUT(PIN = "R.F. OUTPUT")
1.1. Frequency
1.2. Initial Accuracy
a. @ Temperature
b. After time on power
c. Within time period
following date code
d. @ VCO Input voltage
1.3. Waveform
1.4. Level
1.5. Load
1.6. Harmonics
1.7. Spurious
2. FREQUENCY STABILITY
2.1. Ambient
2.2. Aging
a. At time of shipment
b. After indefinite storage
i. Daily
ii. Yearly
iii.10 years
2.3. Voltage
2.4. Load
2.5. Warm-up
2.6. Phase Noise
a. @ 10 Hz
b. @ 100 Hz
c. @ 1 kHz
d. @ 10 kHz
e. @ 100 kHz
100.000000 MHz
< ±2x10-7
+25 ±1°C
30 ±5 minutes
90 days
+4.0 ±0.001 V
Sine wave
+9 ±2 dBm
50 Ω
< -30 dBc
< -70 dBc
< ±1x10-7, -30°C to +70°C
(referenced to +25°C)
< ±3x10-9/day
< ±3x10-9 after 30 days
< ±3x10-7
< ±1.2x10-6
< ±2x10-8/±5% change
< ±5x10-8/±5% change
< ±1x10-7 in 10 minutes @ +25 ±1°C
(referenced to 1 hour)
< -90 dBc
< -120 dBc
< -150 dBc
< -155 dBc
< -160 dBc
OUR PERFORMANCE
YOUR REPUTATION
MODEL NO.
OCXO 131-1006
PAGE OF TOTAL
12
DWG. NO. REV.
114-1322
A

No Preview Available !

NIADHDWHNF(OCXO 131-1006)
www.isotemp.com www.taitien.com
3. ELECTRICAL FREQUENCY ADJUSTMENT (PIN = "VCO INPUT")
3.1. Range
> ±1.5x10-6
Referenced to frequency at nominal Center Voltage
3.2. Control
+0 to Vref +8 V
3.3. Slope
Positive
3.4. Center Voltage
+4 V
NOTE: When not connected, VCO INPUT is internally held at this voltage.
3.5. Linearity
< ±10%
3.6. Input impedance
> 25 kΩ
4. INPUT POWER (PIN = "+VDC")
4.1. Voltage
4.2. Current
4.3. Steady state
+12 V ±5%
< 350 mA @ turn on
< 1.5 Watts @ +25°C
5. REFERENCE VOLTAGE (PIN = "REFERENCE VOLTAGE"), an output
5.1. Voltage
+8 V ±5%
5.2. Load
> 9 kΩ
5.3. Temperature stability
< ±0.02 V
(Over temperature range in 2.1)
6. ENVIRONMENTAL
6.1. Storage temperature
6.2. Vibration (non-operating)
6.3. Shock (non-operating)
-40°C to +85°C
MIL-STD-202, Method 201 (0.06"
Total p-p, 10 to 55 Hz)
MIL-STD-202, Method 213, Test
Condition J (30 g, 11 ms half-sine)
7. RoHS
All units supplied under this MODEL NUMBER are RoHS compliant.
8. MECHANICAL(Outline drawing)
8.1. Applicable series
8.2. Model number
8.3. Coding
8.4. Outline drawing
OCXO 131 series
OCXO 131-1006
NIADHDWHNF-100.000000
125-586
OUR PERFORMANCE
YOUR REPUTATION
MODEL NO.
OCXO 131-1006
PAGE OF TOTAL
22
DWG. NO. REV.
114-1322
A

No Preview Available !

MOD:
FREQ.:
S/N:
DATE:
(VIEW FROM TOP)
MARKING THIS
SURFACE
0.63 MAX.
16.00
PIN CONNECTIONS
PIN FUNCTION
1
VCO INPUT
or
(See Note 1) NOT CONNECTED
2
REFERENCE VOLTAGE
or
(See Note 1) OVEN MONITOR
or
NOT CONNECTED
3 +VDC
4 R. F. OUTPUT
5 0 VOLTS & CASE
0.026
0.66
0.20
5.08
MIN.
0.031
DIA. PIN (5 PLACES)
0.79
GLASS STANDOFF
(4 PLACES)
Note 1. If the specification does not specify
parameters for either PIN1 or PIN2 then that
respective PIN is NOT internally CONNECTED.
MARKING
1.43 MAX.
36.32
1.000
25.40
CENT.
3
CL 2
1
4
5
0.700 CENT.
17.78
1.07
27.18
(VIEW FROM BOTTOM)
NUMBERS FOR REFERENCE ONLY
(NOT STAMPED ON UNIT)
MOD:
FREQ.:
S/N:
DATE:
MOD:
FREQ.:
S/N:
DATE:
OSCILLATORS
NAME: OUTLINE DRAWING
(TCXO 141 & OCXO 131 SERIES)
A 0.63 MAX. WAS 0.64 MAX. 1.07 WAS 1.07 MAX.
B NEW FORM AND UPDATED MARKING.
LET REVISION
INCH
mm (REFERENCE ONLY)
Form NO. 120-081E
CODE I.D. NO.
31785
Charlottesville, Virgina USA
SCALE: 1:1
DATE: 12-04-2000
DWN. BY: LRB
APPR'D. BY: DAG
DAG
BTG
BY
TST
TST
APP
12-06-2001
01-05-2011
DATE
TOLERANCES
UNLESS OTHERWISE SPECIFIED:
ANGES: ±1 DEGREE
FRACTIONS: ±1/32 INCH
DECIMALS: .XX ± .015, .XXX ± .010 INCH
MATERIAL: STEEL
FINISH: NICKEL
MARK: LABEL