X5R.pdf 데이터시트 (총 21 페이지) - 파일 다운로드 X5R 데이타시트 다운로드

No Preview Available !

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
X5R Dielectric, 4 – 50 VDC (Commercial Grade)
Overview
KEMET’s X5R dielectric features an 85°C maximum
operating temperature and is considered “semi-stable.”
The Electronics Components, Assemblies & Materials
Association (EIA) characterizes X5R dielectric as a Class
II material. Components of this classification are fixed,
ceramic dielectric capacitors suited for bypass and
decoupling applications or for frequency discriminating
circuits where Q and stability of capacitance characteristics
are not critical. X5R exhibits a predictable change in
capacitance with respect to time and voltage and boasts a
minimal change in capacitance with reference to ambient
temperature. Capacitance change is limited to ±15% from
−55°C to +85°C.
Benefits
• −55°C to +85°C operating temperature range
• Lead (Pb)-free, RoHS and REACH compliant
• Temperature stable dielectric
• EIA 0201, 0402, 0603, 0805, 1206, 1210, and 1812 case
sizes
• DC voltage ratings of 4 V, 6.3 V, 10 V, 16 V, 25 V, 35 V, and
50 V
• Capacitance offerings ranging from 0.01 μF to 100 μF
• Available capacitance tolerances of ±10% and ±20%
• Non-polar device, minimizing installation concerns
• 100% pure matte tin-plated termination finish allowing for
excellent solderability
Applications
Typical applications include decoupling, bypass, and
filtering.
Ordering Information
C 1206
C
107
Ceramic
Case Size Specification/
(L" x W") Series
Capacitance
Code (pF)
0201
0402
0603
0805
1206
1210
C = Standard
Two
significant
digits and
number of
zeros.
M 9PA
C
TU
Capacitance
Tolerance
Rated Voltage
(VDC)
Dielectric
Failure Rate/
Design
Termination Finish1
Packaging/Grade
(C–Spec)
K = ±10%
M = ±20%
7=4
9 = 6.3
8 = 10
4 = 16
3 = 25
6 = 35
5 = 50
P = X5R
A = N/A
C = 100% matte Sn
See
"Packaging
C-Spec
Ordering
Options Table"
1 Additional termination finish options may be available. Contact KEMET for details.
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
One world. One KEMET
C1006_X5R_SMD • 11/9/2018
1

No Preview Available !

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
X5R Dielectric, 4 – 50 VDC (Commercial Grade)
Packaging C-Spec Ordering Options Table
Packaging Type1
Bulk Bag/Unmarked
7" Reel/Unmarked
13" Reel/Unmarked
7" Reel/Marked
13" Reel/Marked
7" Reel/Unmarked/2mm pitch2
13" Reel/Unmarked/2mm pitch2
Packaging/Grade
Ordering Code (C-Spec)
Not required (Blank)
TU
7411 (EIA 0603 and smaller case sizes)
7210 (EIA 0805 and larger case sizes)
TM
7040 (EIA 0603)
7215 (EIA 0805 and larger case sizes)
7081
7082
1 Default packaging is "Bulk Bag". An ordering code C-Spec is not required for "Bulk Bag" packaging.
1 The terms "Marked" and "Unmarked" pertain to laser marking option of capacitors. All packaging options labeled as "Unmarked" will contain capacitors
that have not been laser marked. Please contact KEMET if you require a laser marked option. For more information see "Capacitor Marking".
2 The 2 mm pitch option allows for double the packaging quantity of capacitors on a given reel size. This option is limited to EIA 0603 (1608 metric) case
size devices. For more information regarding 2 mm pitch option see "Tape & Reel Packaging Information".
Dimensions – Millimeters (Inches)
W
T
L
B
S
EIA Size
Code
Metric Size
Code
L
Length
W
Width
T
Thickness
B
Bandwidth
S
Separation
Minimum
Mounting
Technique
0201
04021
06032
0805
12063
12104
0603
1005
1608
2012
3216
3225
0.60 (0.024)
±0.03 (0.001)
1.00 (0.040)
±0.05 (0.002)
1.60 (0.063)
±0.15 (0.006)
2.00 (0.079)
±0.20 (0.008)
3.20 (0.126)
±0.20 (0.008)
3.20 (0.126)
±0.20 (0.008)
0.30 (0.012)
±0.03 (0.001)
0.50 (0.020)
±0.05 (0.002)
0.80 (0.032)
±0.15 (0.006)
1.25 (0.049)
±0.20 (0.008)
1.60 (0.063)
±0.20 (0.008)
2.50 (0.098)
±0.20 (0.008)
See Table 2 for
Thickness
0.15 (0.006)
±0.05 (0.002)
0.30 (0.012)
±0.10 (0.004)
0.35 (0.014)
±0.15 (0.006)
0.50 (0.02)
±0.25 (0.010)
0.50 (0.02)
±0.25 (0.010)
0.50 (0.02)
±0.25 (0.010)
N/A
0.30 (0.012)
0.70 (0.028)
0.75 (0.030)
Solder Reflow
Only
Solder Wave or
Solder Reflow
N/A Solder Reflow
Only
1 For capacitance values ≥ 4.7 µF add 0.15 (0.006) to the width and length tolerance dimensions.
2 For capacitance values ≥ 10 µF add 0.05 (0.002) to the length and width tolerance dimension.
3 For capacitance values ≥ 22 µF add 0.10 (0.004) to the positive bandwidth tolerance dimension.
4 For capacitance values ≥ 22 µF add 0.10 (0.004) to the length and width tolerance dimension and add 0.15 (0.006) to the positive bandwidth tolerance
dimension.
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
C1006_X5R_SMD • 11/9/2018
2

No Preview Available !

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
X5R Dielectric, 4 – 50 VDC (Commercial Grade)
Qualification/Certification
Commercial Grade products are subject to internal qualification. Details regarding test methods and conditions are
referenced in Table 4, Performance & Reliability.
Environmental Compliance
Lead (Pb)-free, RoHS, and REACH compliant without exemptions.
Electrical Parameters/Characteristics
Item Parameters/Characteristics
Operating Temperature Range
Capacitance Change with Reference to
+25°C and 0 Vdc Applied (TCC)
1Aging Rate (Maximum % Capacitance Loss/Decade Hour)
2Dielectric Withstanding Voltage (DWV)
3Dissipation Factor (DF) Maximum Limit at 25°C
4Insulation Resistance (IR) Minimum Limit at 25°C
−55°C to +85°C
±15%
5.0%
250% of rated voltage
(5 ±1 seconds and charge/discharge not exceeding 50mA)
See Dissipation Factor Limit Table
See Insulation Resistance Limit Table
(Rated voltage applied for 120 ±5 seconds at 25°C)
1 Regarding Aging Rate: Capacitance measurements (including tolerance) are indexed to a referee time of 48 or 1,000 hours. Please refer to a part
number specific datasheet for referee time details.
2 DWV is the voltage a capacitor can withstand (survive) for a short period of time. It exceeds the nominal and continuous working voltage of the
capacitor.
3 Capacitance and dissipation factor (DF) measured under the following conditions:
1 kHz ±50 Hz and 1.0 ±0.2 Vrms if capacitance ≤ 10 µF
120 Hz ±10 Hz and 0.5 ±0.1 Vrms if capacitance > 10 µF
4 To obtain IR limit, divide MΩ-µF value by the capacitance and compare to GΩ limit. Select the lower of the two limits.
Note: When measuring capacitance it is important to ensure the set voltage level is held constant. The HP4284 and Agilent E4980 have a feature known
as Automatic Level Control (ALC). The ALC feature should be switched to "ON."
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
C1006_X5R_SMD • 11/9/2018
3

No Preview Available !

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
X5R Dielectric, 4 – 50 VDC (Commercial Grade)
Post Environmental Limits
Dielectric
X5R
High Temperature Life, Biased Humidity, Moisture Resistance
Rated DC
Voltage
Capacitance Dissipation Factor Capacitance
Value
(Maximum %)
Shift
< 1.0 µF
> 25
≥ 1.0 µF
7.5
20.0
Insulation
Resistance
< 2.2 µF
7.5
25
≥ 2.2 µF
20.0
±20%
10% of Initial
Limit
< 0.56 µF
< 25
≥ 0.56 µF
7.5
20.0
Dissipation Factor Limit Table
Rated
DC Voltage
> 25
25
< 25
Capacitance
< 1.0 µF
≥ 1.0 µF
< 2.2 µF
≥ 2.2 µF
< 0.56 µF
≥ 0.56 µF
Dissipation Factor
(Maximum %)
5.0
10.0
5.0
10.0
5.0
10.0
Insulation Resistance Limit Table
EIA Case Size
0201
0402
0603
0805
1206
1210
1812
1,000 Megohm
Microfarads or 100 GΩ
N/A
< .012 µF
< .047 µF
< 0.15 µF
< 0.47 µF
< 0.39 µF
< 2.2 µF
500 Megohm
Microfarads or 10 GΩ
ALL
≥ .012 µF < 1.0 µF
≥ .047 µf < 1.0 µF
≥ 0.15 µF < 1.0 µF
≥ 0.47 µF < 1.0 µF
≥ 0.39 µF < 1.0 µF
≥ 2.2 µF
100 Megohm
Microfarads
N/A
≥ 1.0 µF
≥ 1.0 µF
≥ 1.0 µF
≥ 1.0 µF
≥ 1.0 µF
N/A
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
C1006_X5R_SMD • 11/9/2018
4

No Preview Available !

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
X5R Dielectric, 4 – 50 VDC (Commercial Grade)
Table 1 – Capacitance Range/Selection Waterfall (0201 – 0805 Case Sizes)
Capacitance
Capacitance
Code
Case Size/
Series
Voltage Code
Rated Voltage (VDC)
Capacitance
Tolerance
10,000 pF 103 K M
12,000 pF 123 K M
15,000 pF 153 K M
18,000 pF 183 K M
22,000 pF 223 K M
27,000 pF 273 K M
33,000 pF 333 K M
39,000 pF 393 K M
47,000 pF 473 K M
56,000 pF 563 K M
68,000 pF 683 K M
82,000 pF 823 K M
0.10 µF
104 K M
0.12 µF
124 K M
0.15 µF
154 K M
0.18 µF
184 K M
0.22 µF
224 K M
0.27 µF
274 K M
0.33 µF
334 K M
0.39 µF
394 K M
0.47 µF
474 K M
0.56 µF
564 K M
0.68 µF
684 K M
0.82 µF
824 K M
1.0 µF
105 K M
1.2 µF
125 K M
1.5 µF
155 K M
1.8 µF
185 K M
2.2 µF
225 K M
2.7 µF
275 K M
3.3 µF
335 K M
3.9 µF
395 K M
4.7 µF
475 K M
5.6 µF
565 K M
6.8 µF
685 K M
8.2 µF
825 K M
10 µF
106 K M
12 µF
126 K M
15 µF
156 K M
18 µF
186 K M
22 µF
226 K M
47 µF
476 K M
Rated Voltage (VDC)
Capacitance
Capacitance
Code
Voltage Code
Case Size/Series
C0201C
C0402C
C0603C
C0805C
7984798435798435798435
Product Availability and Chip Thickness Codes – See Table 2 for Chip Thickness Dimensions
AB AB AB AB BB BB BB BB
BB BB BB BB
BB BB BB BB
BB BB BB BB
BB BB BB BB
BB BB BB BB
BB BB BB BB
BB BB BB BB
BB BB BB BB
BB BB BB BB
BB BB BB BB
BB BB BB BB
AB AB
BB BB BB BB BB
CG CG CG CG CG
BB BB
BB BB
BB BB BB BB
BB BB BB¹
BB¹
BE¹ BE¹
BF¹ BF¹
CG CG CG CG
CG CG CG CG
CG CG CG CG
CG CG CG CG
CG CG CG CG CG
CG CG CG CG
CG CG CG CG
CG CG CG CG
CG CG CG CG CJ
CG CG CG CG
CG CG
CG CG CG
CG¹ CG¹ CK¹
DG DG DG DG DG
DP DP DP DP DP
DP DP DP DP DE
DF DF DF DF DF
DP DP DP DP DG DG
DN DN DN DN
DN DN DN DN
DP DP DP DP
DG DG DG DG DG
DL DL DL DL
DL DL DL DG
DG DG DG DG
DG DG DG DG DG
DG DG DG
DG DG DG
DG DG DG DG DH
DG DG DH¹
DH¹ DH¹
7984798354798435798435
C0201C
C0402C
C0603C
C0805C
xx¹ Available only in M tolerance.
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
C1006_X5R_SMD • 11/9/2018
5