B101EAN01.2.pdf 데이터시트 (총 26 페이지) - 파일 다운로드 B101EAN01.2 데이타시트 다운로드

No Preview Available !

Product Specification
AU OPTRONICS CORPORATION
(V ) Preliminary Specifications
( ) Final Specifications
Module
Model Name
Note ( )
10.1”(10.01”) WXGA 16:10 Color TFT-LCD
B101EAN01.2 (H/W: 0A) LCM
LED Backlight without driving circuit design
Customer
Date
Approved by
Date
Checked &
Approved by
Date
Trista Jiang
July 09, 2013
Prepared by
Chris Wang
July 09, 2013
Note: This Specification is subject to change
without notice.
MPBU Marketing Division
AU Optronics corporation
B101EAN01.2 Document Version : 0.1
1 of 26

No Preview Available !

Product Specification
AU OPTRONICS CORPORATION
Contents
1. Handling Precautions......................................................... 4
2. General Description ........................................................... 5
2.1 Display Specification ................................................................................................................. 5
2.2 Optical Characteristics ............................................................................................................... 6
3. Functional Block Diagram ................................................ 11
4. Absolute Maximum Ratings ............................................. 12
4.1 Absolute Ratings of TFT LCD Module.................................................................................... 12
4.2 Absolute Ratings of Environment ............................................................................................ 12
5. Electrical Characteristics ................................................. 13
5.1 TFT LCD Module .................................................................................................................... 13
5.2 Backlight Unit .......................................................................................................................... 15
6. Signal Interface Characteristic ........................................ 16
6.1 Pixel Format Image .................................................................................................................. 16
6.2 The Input Data Format ............................................................................................................. 17
6.3 Integration Interface Requirement............................................................................................ 19
6.5 Power ON/OFF Sequence ........................................................................................................ 23
7. Mechanical Characteristics .............................................. 24
7.1 Standard Front View................................................................................................................. 24
7.2 Standard Rear View.................................................................................................................. 25
8. Shipping and Package...................................................... 26
8.1 Shipping Label Format............................................................................................................. 26
8.2 Carton Label Format ................................................................................................................ 26
8.3 hipping Package of Palletizing Sequence ................................................................................ 26
B101EAN01.2 Document Version : 0.1
2 of 26

No Preview Available !

Product Specification
AU OPTRONICS CORPORATION
Record of Revision
Version and Date Page
Old description
0.0 06/13/2013
0.1 07/09/2013
Page. 5 White Luminance :
Page. 6 ILED=22mA
300 typ. (5 points average)
245 min. (5 points average)
New Description
1st version
White Luminance :
ILED=24mA
350 typ. (5 points average)
280 min. (5 points average)
Remark
B101EAN01.2 Document Version : 0.1
3 of 26

No Preview Available !

Product Specification
AU OPTRONICS CORPORATION
1. Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or
spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard
surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human
earth when handling.
7) Do not open or modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt
the Interface Connector of the TFT Module.
10)After installation of the TFT Module into an enclosure (Notebook PC Bezel, for example),
do not twist nor bend the TFT Module even momentary. At designing the enclosure, it
should be taken into consideration that no bending/twisting forces are applied to the TFT
Module from outside. Otherwise the TFT Module may be damaged.
11)Disconnecting power supply before handling LCD modules, it can prevent electric shock,
DO NOT TOUCH the electrode parts, cables, connectors and LED circuit part of TFT
module that a LED light bar build in as a light source of back light unit. It can prevent
electrostatic breakdown.
B101EAN01.2 Document Version : 0.1
4 of 26

No Preview Available !

Product Specification
AU OPTRONICS CORPORATION
2. General Description
This specification applies to the 10.1 inch-wide Color a-Si TFT-LCD Module B101EAN01.2.
The display supports the 16:10 WXGA, 1280(H) x800(V) screen and 16.7M colors (RGB 6-bits
data driver with FRC). All input signals are LVDS interface compatible and this module doesn’t
contain an inverter board for backlight.
2.1 Display Specification
The following items are characteristics summary on the table at 25 condition:
Items
Screen Diagonal
Active Area
Pixels H x V
Pixel Pitch
Pixel Format
Display Mode
White Luminance
(ILED=24mA)
(Note: ILED is LED current)
Luminance Uniformity
Contrast Ratio
Response Time
Nominal Input Voltage VDD
Power Consumption
Weight
Physical Size
Include bracket
Unit
[mm]
[mm]
[mm]
Specifications
255.85 (10.07 inch)
216.96(H) x 135.6(V)
1280 x 3(RGB) x 800
0.1695 X 0.1695
R.G.B. Vertical Stripe
AHVA, Normally Black
[cd/m2]
350 typ. (5 points average)
280 min. (5 points average)
[ms]
[Volt]
[Watt]
1.25 max. (5 points)
TYP. 800:1 / Min 600:1
Typ. 30 (White to black)
3.3V typ
2.7 W(Max) w/o LED driver
[Grams] 145g Max
Length
Width
Min
227.6
147.3
Typ
227.72
147.8
[mm] Thickness
Panel Side
2.37
Max
228.02
148.1
Electrical Interface
Glass Thickness
Surface Treatment
(panel only)
[mm]
Thickness
PCBA Side
1 channel LVDS
0.25/0.25 (w/o PF)
HC, Hardness 2H
4.6
B101EAN01.2 Document Version : 0.1
5 of 26