M-959.pdf 데이터시트 (총 5 페이지) - 파일 다운로드 M-959 데이타시트 다운로드

No Preview Available !

M-959
Dial Pulse Counter and Hook Status Monitor
Features
Time-guarded dial pulse counting
10 or 20 PPS dialing speeds pin selectable
Tri-state data outputs
Valid data output strobe
Data strobe control for use in interrupt-driven
environments
Independent hook status monitoring
Low-power CMOS construction
Pin Diagram
Description
The M-959 is a low-power dial pulse counter and
hook status monitor. Contained in a 14-pin package,
the M-959 requires no external components except a
single 3.579 MHz television color burst crystal.
The M-959 is typically connected to a loop current
sensing circuit, which is connected in series with the
voice pair (Tip and Ring) of a telephone line. The M-
959 receives pulses from the loop current sense cir-
cuit and translates them into logic level outputs
indicating hook status and decoded dialed digits.
Logic inputs to the M-959 select dialed digit speeds
and control Data and Strobe outputs supporting bus
interrupt driven implementations.
Ordering Information
Part #
M-959
Description
14-pin plastic DIP
Block Diagram
DS-M959-R3
www.clare.com
1

No Preview Available !

M-959
Absolute Maximum Ratings
DC Supply Voltage
6.0 V
Any Input Voltage Relative to VDD
Any Input Voltage Relative to VSS
Operating Temperature Range
+0.3 V
-0.3 V
-40˚C to +85˚C
Storage Temperature Range
-55˚C to + 125˚C
* Exceeding these ratings may permanently damage the M-959.
Absolute Maximum Ratings are stress ratings. Stresses in
excess of these ratings can cause permanent damage to
the device. Functional operation of the device at these or
any other conditions beyond those indicated in the opera-
tional sections of this data sheet is not implied. Exposure of
the device to the absolute maximum ratings for an extend-
ed period may degrade the device and effect its reliability.
Specifications
VDD - VSS = 2.5 through 6.0 V unless otherwise noted.
Parameter
Conditions
Min
Typ
Signal Timing Break Recognition
10 PPS
45
20 PPS 30 –
Spurious Break
– 0–
Rejection
Make Recognition 10 PPS 30 –
20 PPS 15 –
Interdigit Time (IDT)
10 PPS
285 300
20 PPS
142.5
150
Off-hook Delay
– 95 100
On-hook Delay
– 285 300
LC Hysteresis
– 1 1.5
EOD (End of Digit)
10 PPS
95 100
Recognition
20 PPS
47.5 50
STROBE Active
10 PPS
190 200
20 PPS
95 100
Data Change Before
1.0 1.5
Logic Input Input Voltages
Logic 0
0.0 2.25
Requirements
Logic 1
3.5 2.75
Input Current
––
Pull Up/Down Resistance
––
Logic Output Output Voltages
Logic 0
0.0
Characteristics
Logic 1
4.5
Output Currents
Vout = 2.5V
-2.1
-4.2
Vout = 4.6V
-0.44
-0.88
Vout = 0.4V
0.44
0.88
Tri-State Leakage – – –
Power
Supply Current
Requirement
– ––
Notes:
1. VDD - VSS = 5.0V
2. Maximimum is 30% of VDD - VSS
3. Minimum is 70% of VDD - VSS
4. No load.
5. Typical column for reference only.
Max
85
40
10
65
24
315
157.5
105
315
2
105
52.5
210
105
2.0
1.5
5.0
± 30
2.0
0.5
5.0
± 1.0
2.0
Units
ms
ms
ms
ms
ms
ms
ms
ms
ms
ms
ms
ms
ms
ms
ms
V
V
µA
mA
V
V
mA
mA
mA
µA
mA
Notes
1, 2
1,3
1, 4
1, 3
1
1
1
2
www.clare.com
Rev. 3

No Preview Available !

M-959
Pin Functions
Pin
LC
OH
10/20
D3-D0
OE
XIN
XOUT
Clear
Strobe
Function
Loop Current Input. Signal from phone line to be monitored for dial pulse signaling and hook status. Active low,
internally pulled high.
Off-hook Output. Hook status of phone line. Active (off-hook) high.
Pulse Speed Input. Low for 10 pulse per second, high for 20 pulse per second. Internally pulled low.
Data Outputs. Binary decoded rotary dialed digit. Active during valid digit time (strobe high), low at any other time.
Digit Dialed D3 D2 D1 D0
10 0 0 1
20 0 1 0
30 0 1 1
40 1 0 0
50 1 0 1
60 1 1 0
70 1 1 1
81 0 0 0
91 0 0 1
01 0 1 0
Output Enable Input. Active high, a log low tri-states D3 through D0 outputs. Internally pulled high.
Crystal Oscillator Input
Crystal Oscillator Output.
Strobe Control Input. Momentary high during digit valid time resets STROBE latch output low until next valid
digit is received. Internally pulled low.
Digit Valid Output. Indicates valid digit data present on D3 through D0. Active high.
Timing Diagram
Rev. 3 www.clare.com
3

No Preview Available !

M-959
Mechanical Dimensions
Tolerances
Inches
Metric (mm)
Min Max
Min Max
A .210
5.33
A1 .015
.38
b .014 .022
.36 .56
b2 .045
.070
1.14 1.78
C .008 .014
.20 .36
D .735 .775
18.67
19.70
E .300 .325
7.62 8.26
E1 .240
.280
6.10 7.1
e 100 BSC
2.54 BSC
ec 0˚
15˚
0˚ 15˚
L .115 .150
2.92 3.81
Dimensions
mm
(inches)
4
www.clare.com
Rev. 3

No Preview Available !

Worldwide Sales Offices
CLARE LOCATIONS
Clare Headquarters
78 Cherry Hill Drive
Beverly, MA 01915
Tel: 1-978-524-6700
Fax: 1-978-524-4900
Toll Free: 1-800-27-CLARE
Clare Switch Division
4315 N. Earth City Expressway
Earth City, MO 63045
Tel: 1-314-770-1832
Fax: 1-314-770-1812
Clare Micronix Division
145 Columbia
Aliso Viejo, CA 92656-1490
Tel: 1-949-831-4622
Fax: 1-949-831-4628
SALES OFFICES
AMERICAS
Americas Headquarters
Clare
78 Cherry Hill Drive
Beverly, MA 01915
Tel: 1-978-524-6700
Fax: 1-978-524-4900
Toll Free: 1-800-27-CLARE
Eastern Region
Clare
603 Apache Court
Mahwah, NJ 07430
Tel: 1-201-236-0101
Fax: 1-201-236-8685
Toll Free: 1-800-27-CLARE
Central Region
Clare Canada Ltd.
3425 Harvester Road, Suite 202
Burlington, Ontario L7N 3N1
Tel: 1-905-333-9066
Fax: 1-905-333-1824
Western Region
Clare
1852 West 11th Street, #348
Tracy, CA 95376
Tel: 1-209-832-4367
Fax: 1-209-832-4732
Toll Free: 1-800-27-CLARE
Canada
Clare Canada Ltd.
3425 Harvester Road, Suite 202
Burlington, Ontario L7N 3N1
Tel: 1-905-333-9066
Fax: 1-905-333-1824
EUROPE
European Headquarters
CP Clare nv
Bampslaan 17
B-3500 Hasselt (Belgium)
Tel: 32-11-300868
Fax: 32-11-300890
France
Clare France Sales
Lead Rep
99 route de Versailles
91160 Champlan
France
Tel: 33 1 69 79 93 50
Fax: 33 1 69 79 93 59
Germany
Clare Germany Sales
ActiveComp Electronic GmbH
Mitterstrasse 12
85077 Manching
Germany
Tel: 49 8459 3214 10
Fax: 49 8459 3214 29
Italy
C.L.A.R.E.s.a.s.
Via C. Colombo 10/A
I-20066 Melzo (Milano)
Tel: 39-02-95737160
Fax: 39-02-95738829
Sweden
Clare Sales
Comptronic AB
Box 167
S-16329 Spånga
Tel: 46-862-10370
Fax: 46-862-10371
United Kingdom
Clare UK Sales
Marco Polo House
Cook Way
Bindon Road
Taunton
UK-Somerset TA2 6BG
Tel: 44-1-823 352541
Fax: 44-1-823 352797
ASIA/PACIFIC
Asian Headquarters
Clare
Room N1016, Chia-Hsin, Bldg II,
10F, No. 96, Sec. 2
Chung Shan North Road
Taipei, Taiwan R.O.C.
Tel: 886-2-2523-6368
Fax: 886-2-2523-6369
http://www.clare.com
Clare, Inc. makes no representations or warranties with respect to
the accuracy or completeness of the contents of this publication
and reserves the right to make changes to specifications and
product descriptions at any time without notice. Neither circuit
patent licenses nor indemnity are expressed or implied. Except as
set forth in Clare’s Standard Terms and Conditions of Sale, Clare,
Inc. assumes no liability whatsoever, and disclaims any express or
implied warranty, relating to its products including, but not limit-
ed to, the implied warranty of merchantability, fitness for a partic-
ular purpose, or infringement of any intellectual property right.
The products described in this document are not designed,
intended, authorized or warranted for use as components in sys-
tems intended for surgical implant into the body, or in other appli-
cations intended to support or sustain life, or where malfunction
of Clare’s product may result in direct physical harm, injury, or
death to a person or severe property or environmental damage.
Clare, Inc. reserves the right to discontinue or make changes to its
products at any time without notice.
Specification: DS-M959-R3
©Copyright 2001, Clare, Inc.
All rights reserved. Printed in USA.
7/20/01