DL4756.pdf 데이터시트 (총 2 페이지) - 파일 다운로드 DL4756 데이타시트 다운로드

No Preview Available !

MCC
  omponents
21201 Itasca Street Chatsworth

  !"#
$ %    !"#
Features
Wide Voltage Range Available
Glass Package
High Temp Soldering: 260°C for 10 Seconds At Terminals
For Surface Mount Applications
DL4728
THRU
DL4764
1 Watt
Zener Diode
3.3 to 100 Volts
Maximum Ratings
Operating Temperature: -55°C to +150°C
Storage Temperature: -55°C to +150°C
1 Watt DC Power Dissipation
Power Derating: 10.0mW/°C above 100°C
Maximum Forward Voltage @ 200mA: 1.2 Volts
Figure 1 - Typical Temperature Coefficient
40
mV/°C
20
0
0 20 40
VZ
Typical Temperature Coefficient (mV/°C) – versus – Zener Voltage (VZ)
Figure 2 - Derating Curve
1.0
W
0.5
25 100 150 200
Temperature °C
Power Dissipation (W) - Versus - Temperature °C
GLASS MELF
Cathode Mark
C
B
A
INCHES
DIM MIN
MAX
A .190 .205
B --- .022
C .095 .105
MM
MIN
4.80
---
2.40
MAX
5.20
.55
2.67
NOTE
Nominal
SUGGESTED SOLDER
PAD LAYOUT
.210”
.115”
.035”
www.mccsemi.com

No Preview Available !

DL4728 thru DL4764
MCC
ELECTRICAL CHARACTERISTICS @25°C
MCC
PART
NUMBER
DL4728
DL4729
DL4730
DL4731
DL4732
DL4733
DL4734
DL4735
DL4736
DL4737
DL4738
DL4739
DL4740
DL4741
DL4742
DL4743
DL4744
DL4745
DL4746
DL4747
DL4748
DL4749
DL4750
DL4751
DL4752
DL4753
DL4754
DL4755
DL4756
DL4757
DL4758
DL4759
DL4760
DL4761
DL4762
DL4763
DL4764
ZENER
VOLTAGE
VZ
VOLTS
3.3
3.6
3.9
4. 3
4.7
5.1
5.6
6.2
6.8
7.5
8.2
9.1
10
11
12
13
15
16
18
20
22
24
27
30
33
36
39
43
47
51
56
62
68
75
82
91
100
TEST
CURRENT
IZT
mA
76
69
64
58
53
49
45
41
37
34
31
28
25
23
21
19
17
15.5
14
12.5
11.5
10.5
9.5
8.5
7.5
7.0
6.5
6.0
5.5
5.0
4.5
4.0
3.7
3.3
3.0
2.8
2.5
MAXIMUM
DYNAMIC
IMPEDANCE
ZZT @ IZT
OHMS
10
10
9
9
8
7
5
2
3.5
4.0
4.5
5.0
7
8
9
10
14
16
20
22
23
25
35
40
45
50
60
70
80
95
110
125
150
175
200
250
350
MAXIMUM
REVERSE
CURRENT
IR @ VR
µA
100
100
50
10
10
10
10
10
10
10
10
10
10
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
TEST
VOLTAGE
VR
VOLTS
1
1
1
1
1
1
2
3
4
5
6
7
7.6
8.4
9.1
9.9
11.4
12.2
13.7
15.2
16.7
18.2
20.6
22.8
25.1
27.4
29.7
32.7
35.8
38.8
42.6
47.1
51.7
56.0
62.2
69.2
76.0
MAXIMUM
REGULATOR
CURRENT
IZM
TA = 50°C
mA
276
252
234
217
193
178
162
146
133
121
110
100
91
83
76
69
61
57
50
45
41
38
34
30
27
25
23
22
19
18
16
14
13
12
11
10
9
MAXIMUM
KNEE
IMPEDANCE
ZZK @ IZK
TEST
CURRENT
IZK
OHMS
400
400
400
400
500
550
600
700
700
700
700
700
700
700
700
700
700
700
750
750
750
750
750
1000
1000
1000
1000
1500
1500
1500
2000
2000
2000
2000
3000
3000
3000
mA
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
0.5
0.5
0.5
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
MAXIMUM
SURGE
CURRENT
IS
mA
1380
1260
1190
1070
970
890
810
730
660
605
550
500
454
414
380
344
304
285
250
225
205
190
170
150
135
125
115
110
95
90
80
70
65
60
55
50
45
NOTE 1 The JEDEC type numbers shown have A 5% tolerance on nominal zener voltage.
No suffix signifies A 10% tolerance, C signifies 2%, and D signifies 1% tolerance.
NOTE 2 The zener impedance is derived from the 60Hz AC voltage, which results when an AC current having an rms value equal to
10% of the DC zener current (Izt or Izk) is superimposed on Izt or Izk. Zener impedance is measured at two points to insure
a sharp knee on the breakdown curve and eliminate unstable units.
NOTE 3 The reverse surge current is measured at 25oC ambient using a 1/2 square wave or equivalent sine wave pulse 1/120 second
duration superimposed on Izt
NOTE 4 Voltage measurements to be performed 90 seconds after application of DC current.
www.mccsemi.com