ISL6414.pdf 데이터시트 (총 4 페이지) - 파일 다운로드 ISL6414 데이타시트 다운로드

No Preview Available !

®
Data Sheet
October 2003
ISL6414
FN9128
Triple Output, Low-Noise LDO Regulator
with Integrated Reset Circuit
The ISL6414 is an ultra low noise triple output LDO regulator
with microprocessor reset circuit and is optimized for
powering wireless chip sets. The IC accepts an input voltage
range of 3.0V to 3.6V and provides three regulated output
voltages: 1.8V (LDO1), 2.84V (LDO2), and another ultra
clean 2.84V (LDO3). On chip logic provides sequencing
between LDO1 and LDO2 for BBP/MAC and I/O supply
voltage outputs. LDO3 features ultra low noise that does not
typically exceed 30µV RMS to aid VCO stability. High
integration and the thin Quad Flat No-lead (QFN) package
makes ISL6414 an ideal choice to power many of today’s
small form factor industry standard wireless cards, such as
PCMCIA, mini-PCI and Cardbus-32.
The ISL6414 uses an internal PMOS transistor as the pass
device. The SHDN pin controls LDO1 and LDO2 outputs
whereas SHDN3 controls LDO3 output. Internal voltage
sequencing insures that LDO1 output (1.8V supply) is
always stabilized before LDO2 is turned on. When powering
down, power to the LDO2 is removed before the LDO1
output goes off. The ISL6414 also integrates RESET
function, which eliminates the need for additional RESET IC
required in WLAN applications. The IC asserts a RESET
signal whenever the VIN supply voltage drops below a preset
threshold, keeping it asserted for at least 25ms after VIN has
risen above the reset threshold. An output fault detection
circuit indicates loss of regulation on LDO1. Other features
include an over current protection, thermal shutdown and
reverse battery protection.
Ordering Information
TEMP. RANGE
PART NUMBER
(oC)
PACKAGE
PKG.
DWG. #
ISL6414IR
-40 to +85 16 Ld QFN L16.4x4
ISL6414IRZ
-40 to +85 16 Ld QFN L16.4x4
NOTE: " Z " Suffix: Intersil Lead Free products employ special lead
free material sets; molding compounds / die attach materials and
100% matte tin plate termination finish, which is compatible with both
SnPb and lead free soldering operations. Intersil Lead Free products
are MSL classified at lead free peak reflow temperatures that meet
or exceed the lead free requirements of IPC/JEDEC J Std-020B.
Tape and Reel available. Add " - T " suffix for tape and reel packing
option. (eg. ISL6414IRZ-T for lead free tape and reel)
Features
• Small DC-DC Converter Size
- Three LDOs and RESET Circuitry in a Low-Profile
4x4mm QFN Package
• High Output Current
- LDO1, 1.8V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500mA
- LDO2, 2.84V. . . . . . . . . . . . . . . . . . . . . . . . . . . . 300mA
- LDO3, 2.84V. . . . . . . . . . . . . . . . . . . . . . . . . . . . 200mA
• Ultra-Low Dropout Voltage
- LDO2, 2.84V. . . . . . . . . . . . . . . 125mV (typ.) at 300mA
- LDO3, 2.84V. . . . . . . . . . . . . . . 100mV (typ.) at 200mA
• Ultra-Low Output Voltage Noise
- <30µVRMS (typ.) for LDO3 (VCO Supply)
• Stable with Smaller Ceramic Output Capacitors
• Voltage Sequencing for BBP/MAC and Analog Supplies
• Extensive Protection and Monitoring Features
- Over current and short circuit protection
- Thermal shutdown
- Reverse battery protection
- FAULT indicator
• Logic-Controlled Dual Shutdown Pins
• Integrated Microprocessor Reset Circuit
- Programmable Reset Delay
- Complimentary Reset Outputs
• Proven Reference Design for Total WLAN System
Solution
• QFN Package Option
- Compliant to JEDEC PUB95 MO-220 QFN - Quad Flat
No Leads - Product Outline
- Near Chip-Scale Package Footprint Improves PCB
Efficiency and Is Thinner in Profile
- Lead-Free Option Available (“Z” suffix)
Applications
• PRISM® 3, PRISM GT™, and PRISM WWR Chipsets
• WLAN Cards
- PCMCIA, Cardbus32, MiniPCI Cards
- Compact Flash Cards
• Hand-Held Instruments
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2002. All Rights Reserved. PRISM® 3 and PRISM GT™ are trademarks of GlobespanVirata, Inc.
All other trademarks mentioned are the property of their respective owners.

No Preview Available !

Pinout
ISL6414 (QFN)
TOP VIEW
ISL6414
16 15 14 13
RESET 1
12 OUT1
CT 2
11 CC1
SHDN 3
SHDN3 4
10 OUT2
9 CC2
5678
Typical Application Schematic
+3.3V
VIN
+ C8
3.3µF
+2.84V
VOUT3
1
2
C7
0.01µF
3
4
RESET
CT
SHDN
ISL6414
SHDN3
OUT1
CC1
OUT2
CC2
12
11
10
9
C4
0.033µF
C3
0.033µF
+1.8V
VOUT1
+2.84V
VOUT2
C2
3.3µF
C1
3.3µF
C5
3.3µF
EE
C6
0.033µF
2

No Preview Available !

Functional Block Diagram
ISL6414
Gm
BAND
GAP
REF.
1.2V
WINDOW
COMP
+-
LDO1
VIN
15 FAULT
THERMAL
SHUT
DOWN
150oC
Gm
+-
LDO2
VIN 13
VIN 14
OUT1 12
CC1 11
OUT2 10
VIN
3 SHDN
4 SHDN3
CONTROL
LOGIC
2 CT
16 RESET
1 RESET
8 GND
ENABLES
RESET
POR POR
Gm
+-
LDO3
CC2 9
OUT3 5
CC3 6
GND3
7
3

No Preview Available !

ISL6414
Quad Flat No-Lead Plastic Package (QFN)
Micro Lead Frame Plastic Package (MLFP)
L16.4x4
16 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE
(COMPLIANT TO JEDEC MO-220-VGGC ISSUE C)
SYMBOL
A
A1
A2
A3
b
D
D1
MILLIMETERS
MIN NOMINAL MAX
0.80 0.90 1.00
- - 0.05
- - 1.00
0.20 REF
0.23 0.28 0.38
4.00 BSC
3.75 BSC
NOTES
-
-
9
9
5, 8
-
9
D2 1.95 2.10 2.25 7, 8
E
4.00 BSC
-
E1 3.75 BSC 9
E2 1.95 2.10 2.25 7, 8
e
0.65 BSC
-
k 0.25
-
--
L 0.35 0.60 0.75 8
L1 -
- 0.15 10
N 16 2
Nd 4 3
Ne 4 3
P-
- 0.60 9
θ-
- 12 9
Rev. 4 10/02
NOTES:
1. Dimensioning and tolerancing conform to ASME Y14.5-1994.
2. N is the number of terminals.
3. Nd and Ne refer to the number of terminals on each D and E.
4. All dimensions are in millimeters. Angles are in degrees.
5. Dimension b applies to the metallized terminal and is measured
between 0.15mm and 0.30mm from the terminal tip.
6. The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
7. Dimensions D2 and E2 are for the exposed pads which provide
improved electrical and thermal performance.
8. Nominal dimensions are provided to assist with PCB Land Pattern
Design efforts, see Intersil Technical Brief TB389.
9. Features and dimensions A2, A3, D1, E1, P & θ are present when
Anvil singulation method is used and not present for saw
singulation.
10. Depending on the method of lead termination at the edge of the
package, a maximum 0.15mm pull back (L1) maybe present. L
minus L1 to be equal to or greater than 0.3mm.
All Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice.
Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable.
However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its
use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
4