TL072.pdf 데이터시트 (총 16 페이지) - 파일 다운로드 TL072 데이타시트 다운로드

No Preview Available !

TL072, TL072A, TL072B
Low noise JFET dual operational amplifiers
Datasheet - production data
D
SO8
Pin connections (top view)
1
2-
3+
4
8
7
-6
+5
1 - Output 1
2 - Inverting input 1
3 - Non-inverting input 1
4 - VCC-
5 - Non-inverting input 2
6 -Inverting input 2
7 - Output 2
8 - VCC+
Features
Wide common-mode (up to VCC+) and
differential voltage range
Low input bias and offset current
Low noise en = 15 nV/√Hz (typ)
Output short-circuit protection
High input impedance JFET input stage
Low harmonic distortion: 0.01 % (typical)
Internal frequency compensation
Latch-up free operation
High slew rate: 16 V/µs (typ)
Related products
See TL071 for single op amp version
See TL074 for quad op amp version
Description
The TL072, TL072A, and TL072B are high speed
JFET input dual operational amplifiers
incorporating well-matched, high-voltage JFET
and bipolar transistors in a monolithic integrated
circuit.
The devices feature high slew rates, low input
bias and offset current, and low offset voltage
temperature coefficients.
June 2014
DocID2298 Rev 8
This is information on a product in full production.
1/16
www.st.com

No Preview Available !

Contents
TL072, TL072A, TL072B
Contents
1 Schematic diagram.......................................................................... 3
2 Absolute maximum ratings and operating conditions ................. 4
3 Electrical characteristics ................................................................ 5
4 Parameter measurement information .......................................... 10
5 Typical application ........................................................................ 11
6 Package information ..................................................................... 12
6.1 SO8 package information................................................................ 12
7 Ordering information..................................................................... 14
8 Revision history ............................................................................ 15
2/16 DocID2298 Rev 8

No Preview Available !

TL072, TL072A, TL072B
1 Schematic diagram
Figure 1: Schematic diagram
Schematic diagram
DocID2298 Rev 8
3/16

No Preview Available !

Absolute maximum ratings and operating
conditions
TL072, TL072A, TL072B
2 Absolute maximum ratings and operating conditions
Table 1: Absolute maximum ratings
Symbol
Parameter
VCC
Vin
Vid
Rthja
Rthjc
Tstg
ESD
Supply voltage (1)
Input voltage (2)
Differential input voltage (3)
Thermal resistance junction to ambient,
SO8 (4)
Thermal resistance junction to case,
SO8 (4)
Output short-circuit duration (5)
Storage temperature range
HBM: human body model (6)
MM: machine model (7)
CDM: charged device model (8)
TL072I, AI, BI
TL072C, AC,
BC
±18
±15
±30
125
40
Infinite
-65 to +150
1
200
1.5
Unit
V
°C/W
°C
kV
V
kV
Notes:
(1)All voltage values, except the differential voltage, are with respect to the zero reference level (ground) of the
supply voltages where the zero reference level is the midpoint between VCC+ and VCC-.
(2)The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts,
whichever is less.
(3)Differential voltages are the non-inverting input terminal voltages with respect to the inverting input terminal.
(4)Short-circuits can cause excessive heating. Destructive dissipation can result from simultaneous short-
circuits on all amplifiers.
(5)The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be
limited to ensure that the dissipation rating is not exceeded.
(6)Human body model: 100 pF discharged through a 1.5 kΩ resistor between two pins of the device. This is
done for all couples of pin combinations with other pins floating.
(7)Machine model: a 200 pF cap is charged to the specified voltage, then discharged directly between two pins
of the device with no external series resistor (internal resistor < 5 W). This is done for all couples of pin
combinations with other pins floating.
(8)Charged device model: all pins plus package are charged together to the specified voltage and then
discharged directly to the ground.
Symbol
VCC
Toper
Table 2: Operating conditions
Parameter
Supply voltage
Operating free-air temperature range
TL072I, AI,
BI
TL072C, AC,
BC
6 to 36
-40 to +125
0 to +70
Unit
V
°C
4/16 DocID2298 Rev 8

No Preview Available !

TL072, TL072A, TL072B
Electrical characteristics
3 Electrical characteristics
Table 3: Electrical characteristics at VCC = ±15 V, Tamb = +25 °C (unless otherwise specified).
Symbol
Vio
ΔVio/ΔT
Iio
Iib
Avd
SVR
ICC
Vicm
CMR
Ios
±Vopp
Parameter
Input offset voltage (Rs = 50 Ω)
Tamb = +25 °C
TL072
TL072A
TL072B
Input offset voltage (Rs = 50 Ω)
Tmin Tamb Tmax
TL072
TL072A
TL072B
Input offset voltage drift
Input offset current, Tamb = +25 °C (1)
Input offset current, Tmin Tamb Tmax
Input bias current, Tamb = +25 °C (1)
Input bias current, Tmin Tamb Tmax (1)
Large signal voltage gain
(RL = 2 kΩ, Vo = ±10 V), Tamb = +25 °C
Large signal voltage gain
(RL = 2 kΩ, Vo = ±10 V), Tmin Tamb Tmax
Supply voltage rejection ratio
(RS = 50 Ω), Tamb = +25 °C
Supply voltage rejection ratio
(RS = 50 Ω), Tmin Tamb Tmax
Supply current, no load, Tamb = +25 °C
Supply current, no load, Tmin Tamb Tmax
Input common mode voltage range
Common mode rejection ratio
(RS = 50 Ω), Tamb = +25 °C
Common mode rejection ratio
(RS = 50 Ω), Tmin Tamb Tmax
Output short-circuit current, Tamb = +25 °C
Output short-circuit current,
Tmin Tamb Tmax
Output voltage swing,
Tamb = +25 °C
RL = 2 kΩ
RL =
10 kΩ
Output voltage swing,
Tmin Tamb Tmax
RL = 2 kΩ
RL =
10 kΩ
TL072I, AC, AI, BC, BI
Min. Typ. Max.
3 10
36
13
13
7
5
10
5 100
4
20 200
20
50 200
25
80 86
80
1.4
±11 -12 to
+15
2.5
2.5
80 86
80
10 40 60
10 60
10 12
12 13.5
10
12
TL072C
Min. Typ. Max.
3 10
13
10
5 100
10
20 200
20
25 200
15
70 86
70
1.4
±11 -12
to
+15
70 86
2.5
2.5
70
10 40
10
60
60
10 12
12 13.5
10
12
Unit
mV
µV/°C
pA
nA
pA
nA
V/mV
dB
mA
V
dB
mA
V
DocID2298 Rev 8
5/16