81006.pdf 데이터시트 (총 15 페이지) - 파일 다운로드 81006 데이타시트 다운로드

No Preview Available !

REVISIONS
LTR
DESCRIPTION
DATE (YR-MO-DA)
F Add peak current to absolute maximum ratings. Editorial changes throughout.
G Changes in accordance with NOR 5962-R144-95.
H Make corrections to the switch operation table in 3.3.1. Update boilerplate to
reflect current requirements. -rrp
92-11-24
95-10-20
03-03-10
APPROVED
M. A. FRYE
M. A. FRYE
R. MONNIN
CURRENT CAGE CODE 67268
THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
PMIC N/A
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
REV
HH
SHEET
12
PREPARED BY
Gary J. Zahn
CHECKED BY
William E. Sharp
APPROVED BY
N. A. Hauck
DRAWING APPROVAL DATE
81-10-01
HHHHHHHHHH
3 4 5 6 7 8 9 10 11 12
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216
http://www.dscc.dla.mil
MICROCIRCUIT, LINEAR, CMOS, HIGH LEVEL
ANALOG SWITCHES WITH DRIVERS,
MONOLITHIC SILICON
AMSC N/A
REVISION LEVEL
H
SIZE
A
CAGE CODE
14933
SHEET
DSCC FORM 2233
APR 97
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
1 OF
12
81006
5962-E243-03

No Preview Available !

1. SCOPE
1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in
accordance with MIL-PRF-38535, appendix A.
1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example:
81006
01
X
X
Drawing number
Device type
(see 1.2.1)
Case outline
(see 1.2.2)
Lead finish
(see 1.2.3)
1.2.1 Device type(s). The device type(s) identify the circuit function as follows:
Device type
Generic number
Circuit function
01
IH5040, DG5140
One-channel, 75 ohms, SPST switch
02
IH5041, DG5141
Two-channel, 75 ohms, SPST switch
03
IH5042, DG5142
One-channel, 75 ohms, SPDT switch
04
IH5043, DG5143
Two-channel, 75 ohms, SPDT switch
05
IH5044, DG5144
One-channel, 75 ohms, DPST switch
06
IH5045, DG5145
Two-channel, 75 ohms, DPST switch
07 IH5046
One-channel, 75 ohms, DPDT switch
08 IH5047
One-channel, 75 ohms, 4PST switch
09 IH5140, HI5040 One-channel, 75 ohms, SPST switch
10 IH5141, HI5041 Two-channel, 75 ohms, SPDT switch
11 IH5142, HI5042 One-channel, 75 ohms, SPDT switch
12 IH5143, HI5043 Two-channel, 30 ohms, SPDT switch
13 IH5144, HI5044 One-channel, 30 ohms, DPST switch
14 IH5145, HI5045 Two-channel, 75 ohms, DPST switch
15 HI5046
One-channel, 75 ohms, DPDT switch
16 IH5047, HI5047 One-channel, 75 ohms, 4PST switch
17 HI5046A
One-channel, 30 ohms, DPDT switch
18 HI5047A
One-channel, 30 ohms, 4PST switch
19 IH5148, HI5048 Two-channel, 30 ohms, SPST switch
20 IH5149, HI5049 Two-channel, 30 ohms, DPST switch
21 IH5150, HI5050 One-channel, 30 ohms, SPDT switch
22 IH5151, HI5051 Two-channel, 30 ohms, SPDT switch
1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
Descriptive designator
Terminals
Package style
A
GDFP5-F14 or CDFP6-F14
14
E
GDIP1-T16 or CDIP2-T16
16
I MACY1-X10
10
2 CQCC1-N20
X CDFP3-F14
20
14
1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A.
Flat pack
Dual-in-line
Can
Square leadless chip carrier
Flat pack
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
H
81006
SHEET
2

No Preview Available !

1.3 Absolute maximum ratings.
V+ - V- .................................................................................... 33 V dc
V+ - VD ................................................................................... 30 V dc
VD - V- .................................................................................... 30 V dc
VD - VS .................................................................................... ±22 V dc
VL - V-..................................................................................... 33 V dc
VL - VIN ................................................................................... 30 V dc
VL - VR .................................................................................... 20 V dc
VIN - VR ................................................................................... 20 V dc
VR - V- .................................................................................... 33 V dc
VR - VIN ................................................................................... 2 V dc
Current (any terminal except S or D)...................................... 30 mA
Peak current (source to drain) 1/........................................... 80 mA
Storage temperature range .................................................... -65°C to +150°C
Lead temperature (soldering, 10 seconds) ............................ +300°C
Junction temperature (TJ)....................................................... +175°C
Power dissipation, (PD) 2/:
Cases A and X at TA = +125°C .......................................... 350 mW
Case E at TA = +125°C ...................................................... 400 mW
Case I at TA = +125°C ........................................................ 350 mW
Case 2 at TA = +125°C ....................................................... 350 mW
1.4 Recommended operating conditions.
+VCC ...................................................................................... +15 V dc
-VCC ....................................................................................... -15 V dc
VR .......................................................................................... 0 V dc
VL .......................................................................................... 5 V dc
Ambient operating temperature range (TA) ............................ -55°C to +125°C
Thermal resistance, junction-to-case (θJC) ............................. See MIL-STD-1835
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a
part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed
in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in
the solicitation.
SPECIFICATION
DEPARTMENT OF DEFENSE
MIL-PRF-38535 -- Integrated Circuits, Manufacturing, General Specification for.
STANDARDS
DEPARTMENT OF DEFENSE
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard Electronic Component Case Outlines.
1/ Pulse at 1 ms, 10 percent duty cycle maximum.
2/ For TA = +100°C to +125°C, derate linearly at 12 mW/°C.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
H
81006
SHEET
3

No Preview Available !

HANDBOOKS
DEPARTMENT OF DEFENSE
MIL-HDBK-103 -- List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-
JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer
Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-
PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying
activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan
may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device.
These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MIL-
PRF-38535 is required to identify when the QML flow option is used.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as
specified in MIL-PRF-38535, appendix A and herein.
3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.2 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full ambient operating temperature range.
3.3.1 Switch operation. The analog switches listed below are guaranteed to turn “on” with either a “low” input
(VR VIL 0.8 V) or “high” input (2.4 V VIH VIL) as specified below (see figure 1).
Device types
01, 09
02, 10, 05, 13,
19
03, 11, 21
04, 12, 22
07, 15, 17
06, 08, 14, 16,
18, 20
VIN
2.4 V dc
0.8 V dc
2.4 V dc
0.8 V dc
2.4 V dc
0.8 V dc
2.4 V dc
0.8 V dc
2.4 V dc
0.8 V dc
2.4 V dc
0.8 V dc
Channels ON
1
1, 2
1
2
1, 2
3, 4
2, 3
1, 4
1, 2, 3, 4
Channels OFF
1
1, 2
2
1
3, 4
1, 2
1, 4
2, 3
1, 2, 3, 4
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are described in table I.
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN
listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked as listed in MIL-HDBK-103 (see 6.6 herein). For
packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the
option of not marking the "5962-" on the device.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
H
81006
SHEET
4

No Preview Available !

TABLE I. Electrical performance characteristics.
Conditions
Test
Symbol
-55°C TA +125°C
VCC = ±15 V
Group A
subgroups
unless otherwise specified
Drain source “ON”
resistance
RDS VD = -10 V, IS = 10 mA,
VD = 10 V, IS = -10 mA,
Channel “ON” leakage
current
ID(ON)
Drain “OFF” leakage current ID(OFF)
Source “OFF” leakage
current
IS(OFF)
Input current, input voltage
low
Input current, input voltage
high
Positive supply current
IIL
IIH
+ICC
VD = -7.5 V, IS = 10 mA,
VCC = ±10 V 2/
VD = 7.5 V, IS = -10 mA,
VCC = ±10 V 2/
VS = VD = 10 V,
See 3.3.1 for VIN
VS = VD = -10 V,
See 3.3.1 for VIN
VS = -10 V, VD = 10 V,
See 3.3.1 for VIN
VS = 10 V, VD = -10 V,
See 3.3.1 for VIN
VS = 10 V, VD = -10 V,
See 3.3.1 for VIN
VS = -10 V, VD = 10 V,
See 3.3.1 for VIN
VIN = 0 V
VIN = 2.4 V, 5 V
VIN = 0 V, 5 V
Negative supply current -ICC VIN = 0 V, 5 V
1, 3
2
1, 3
2
1, 3
2
1, 3
2
1, 3
2
1, 3
2
2, 3
1
2, 3
1
2, 3
1
2, 3
1
2, 3
1
2, 3
1
1, 3
2
1, 3
2
1, 3
2
1
2, 3
1, 3
2
1
2, 3
Device
type
Limits
1 - 16
Min
17 - 22
1 - 16
17 - 22
All
All -200
-2
-200
-2
All -100
-1
-100
-1
All -100
-1
-100
-1
All -1
-10
All -1
-1
1-8
9 - 22
1-8
9 - 22
-10
-100
-200
-300
Max
75
150
45
50
75
150
45
50
75
150
75
150
200
2
200
2
100
1
100
1
100
1
100
1
1
1
1
10
10
100
200
300
Unit
1/
nA
nA
nA
µA
µA
µA
µA
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
H
81006
SHEET
5