K1523BA.pdf 데이터시트 (총 2 페이지) - 파일 다운로드 K1523BA 데이타시트 다운로드

No Preview Available !

K1523BA Series
Œ Applications: Phase-Locked Loops (PLL’s); Clock
Recovery; Reference Signal Tracking; Synthesizers;
Frequency Modulation/Demodulation
Π2.0 to 35.0 MHz Frequency Range
Π0.5V to 4.5V Control Voltage
Œ ±25ppm Stability
ΠVariety of Deviation Sensitivity Options
Œ -40°C to 85°C Operating Temperature
5V Voltage Controlled Crystal Oscillators
20,8Km135m52.3CM0BT0aA0I xDM.AHTZE CODE
13,2 mm Max.
8,51 mm Max.
PIN 1
Not Recommended for New Designs. Refer to
K1570A & K1570AQH Series as an Alternative.
ELECTRICAL SPECIFICATIONS
Model
Frequency Range (MHz)
Input Current (mA)
Frequency Control Function
Deviation (ppm)
Minimum
Maximum
Linearity (%)
Modulation Bandwidth (±3dB)
Nominal Control Voltage (V)
Control Voltage Range (V)
Transfer Function
Input Impedance
Frequency Stability (ppm)
Overall
0oC to +70oC
-40oC to +85oC
Temperature Range (oC)
Operating
Storage
Supply Voltage (V)
Symmetry (%) CMOS/TTL
Start Up Time (ms)
Typical SSB Phase Noise (dBC/Hz)
Offset from Carrier
K1523BA
2 to 16
16 to 25
25 to 33
33.1 to 35
< 17
< 19
< 26
(For Custom Deviation Range, Vc Range, etc. - Consult Factory)
> 2KHz
±100
±150
<5
> 20KHz
2.5
0.5 to 4.5
Positive
> 50K@ 10KHz
±100
±190
< 10
Inclusive of Calibration, Temperature, Voltage, Load and Aging
±25 ±40
±50 ±55
45/55
10Hz
100Hz
1KHz
10KHz
100KHz
-40oC to +85oC
-40oC to +125oC
+5.0V ±5%
40/60
<10
-65
-95
-120
-140
-150
PART NUMBERING GUIDE
K1523BA X - Specify Frequency
“Blank” = 0°C to 70°C Operating Temp.
“M” = -40°C to +85°C Operating Temp.
2553 N. Edgington Street, Franklin Park, IL 60131 y Phone: 847.451.1000 y Fax: 847.451.7585
800-888-1499 or www.champtech.com
1

No Preview Available !

K1523BA Series
5V Voltage Controlled Crystal Oscillators
PIN FUNCTION
1 Voltage Control
7 Gnd/ & Case Gnd
8 Output
14 + VCC
SHIPPING TUBE CROSS SECTION
OUTPUT WAVEFORM
TEST CIRCUIT DIAGRAM
MECHANICAL AND ENVIRONMENTAL SPECIFICATIONS
TEST METHODS
Temperature Cycle
Mechanical Shock
Vibration
Humidity Steady State
Thermal Shock
Electrostatic Discharge
Solderability
Hermeticity
Resistance to Soldering
Lead Integrity
Marking Permanence
Life Test
REFERENCE PROCEDURES
DESCRIPTION
MIL-STD-833, Mtd 1010, Cond. B
-55°C to +125°C; Air-to-Air; 100 cycles; 10
min. dwell
MIL-STD-883, Mtd 2002, Cond. B
1500 g’s
MIL-STD 883, Mtd 2007, Cond. B
20-2000 Hz; 0.06 inch; 15g’s; 3 planes
MIL-STD-202, Mtd 103
40°C; 90%-95% R.H.; 56 days
MIL-STD-883, Mtd 1011.7 Cond. B
100°C to 0°C; Water-to-Water; 15 cycles
MIL-STD-883, Mtd 3015 Class II
2 KV to 4 KV Threshold
MIL-STD-883, Mtd 2022.2
Solder dip; Meniscograph Criteria
MIL-STD-883, Mtd 1014.8, Cond. A1 Mass spectro. 2 x 10-8 atmos. CC/sec He
MIL-STD-202, Mtd 210D, Cond. C
260°C; 10 seconds: 1 inch/sec.
MIL-STD-883, Mtd 2004.5, Cond. A, B1 Lead tension & bend stress
MIL-STD-883, Mtd 2015.8
MIL-STD-883, Mtd 1005.6
Resistance to solvents
125°C, powered, 1000 hours minimum
2553 N. Edgington Street, Franklin Park, IL 60131 y Phone: 847.451.1000 y Fax: 847.451.7585
800-888-1499 or www.champtech.com
2