MCR100
ABSOLUTE MAXIMUM RATINGS
SCR
PARAMETER
SYMBOL
RATINGS
UNIT
Peak Repetitive Off-State Voltage(Note 1) MCR100-4
200 V
(TJ=-40 ~ 110°С, Sine Wave, 50 ~ 60Hz; MCR100-6
Gate Open)
MCR100-8
VDRM,VRRM
400
600
V
V
On-Sate RMS Current (Tc=80°С) 180°С Condition Angles
Peak Non-Repetitive Surge Current
(1/2 cycle, Sine Wave, 60Hz, TJ=25°С)
Circuit Fusing Considerations (t=8.3 ms)
IT(RMS)
ITSM
I2t
0.8
10
0.415
A
A
A2s
Forward Peak Gate Power (TA=25°С, Pulse Width 1.0µs)
PGM
0.1
W
Forward Average Gate Power (TA=25°С, t=8.3ms)
Peak Gate Current – Forward (TA=25°С, Pulse Width1.0μs)
PG(AV)
IGM
0.1
1
W
A
Peak Gate Voltage – Reverse (TA=25°С, Pulse Width1.0μs)
Operating Junction Temperature Range
(Rated VRRM and VDRM)
VGRM
TJ
5
-40 ~ +110
V
°С
Storage Temperature Range
TSTG
-40 ~ +150
°С
Note: Absolute maximum ratings are those values beyond which the device could be permanently damaged.
Absolute maximum ratings are stress ratings only and functional device operation is not implied.
THERMAL DATA
PARAMETER
Junction to Ambient
SOT-223
SOT-23/SOT-89
TO-92
SYMBOL
θJA
MAX
180
400
200
UNIT
°С/W
°С/W
°С/W
ELECTRICAL CHARACTERISTICS (TJ=25°С, unless otherwise stated)
PARAMETER
SYMBOL
TEST CONDITIONS
MIN TYP MAX UNIT
OFF CHARACTERISTICS
Peak Forward or Reverse Blocking
Current
TC=25°С
TC=125°С
IDRM,
IRRM
VD=Rated
RGK=1kΩ
VDRM
and
VRRM;
10 μA
100 μA
ON CHARACTERISTICS
Peak Forward On-State Voltage (Note 2)
Gate Trigger Current (Continuous DC) (Note3)
Holding Current
Latch Current
Gate Trigger Voltage
(continuous dc)
TC=25°С
TC=-40°С
TC=25°С
TC=-40°С
TC=25°С
TC=-40°С
VTM ITM=1A Peak @ TA=25°С
IGT VAK=7Vdc, RL=100Ω, TC=25°С
IH
VAK=7Vdc, initiating
current=20mA
IL VAK=7V, Ig=200A
VGT VAK=7Vdc, RL=100Ω
1.7
40 200
0.5 5
10
0.6 10
15
0.62 0.8
1.2
V
μA
mA
mA
mA
mA
V
V
DYNAMIC CHARACTERISTICS
Critical Rate of Rise of Off-State Voltage
Critical Rate of Rise of On-State Current
VD=Rated VDRM, Exponential
dV/dt Waveform, RGK=1000Ω,
20 35
V/μs
TJ=110°С
di/dt
IPK=20A; Pw=10sec;
diG/dt=1A/μsec, Igt=20mA
50 A/μs
Notes: 1. VDRM and VRRM for all types can be applied on a continuous basis. Ratings apply for zero or negative gate
voltage; however, positive gate voltage shall not be applied concurrent with negative potential on the
anode. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of
the devices are exceeded.
2. Indicates Pulse Test Width1.0ms, duty cycle 1%.
3. Does not include RGK in measurement.
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
3 of 6
QW-R301-016.G