80RIA.pdf 데이터시트 (총 9 페이지) - 파일 다운로드 80RIA 데이타시트 다운로드

No Preview Available !

Bulletin I25201 rev. B 03/03
PHASE CONTROL THYRISTORS
Features
Hermetic glass-metal seal
International standard case TO-209AC (TO-94)
Typical Applications
DC motor controls
Controlled DC power supplies
AC controllers
Major Ratings and Characteristics
Parameters
80RIA
Unit
IT(AV)
IT(RMS)
ITSM
@ TC
@ 50Hz
@ 60Hz
I2t @ 50Hz
@ 60Hz
VDRM/VRRM
tq typical
TJ
80
85
125
1900
1990
18
16
400 to 1200
110
- 40 to 125
A
°C
A
A
A
KA2s
KA2s
V
µs
°C
www.irf.com
80RIA SERIES
Stud Version
80A
case style
TO-209AC (TO-94)
1

No Preview Available !

80RIA Series
Bulletin I25201 rev. B 03/03
ELECTRICAL SPECIFICATIONS
Voltage Ratings
Voltage
Type number Code
80RIA
40
80
120
VDRM/VRRM, max. repetitive
peak and off-state voltage
V
400
800
1200
VRSM , maximum non-
repetitive peak voltage
V
500
900
1300
IDRM/IRRM max.
@ TJ = 125°C
mA
15
On-state Conduction
Parameter
IT(AV) Max. average on-state current
@ Case temperature
IT(RMS) Max. RMS on-state current
ITSM Max. peak, one-cycle
non-repetitive surge current
I2t Maximum I2t for fusing
I2t Maximum I2t for fusing
VT(TO)1 Low level value of threshold
voltage
VT(TO)2 High level value of threshold
voltage
rt1 Low level value of on-state
slope resistance
rt2 High level value of on-state
slope resistance
VTM Max. on-state voltage
IH Maximum holding current
IL Typical latching current
80RIA
80
85
125
1900
1990
1600
1675
18
16
12.7
11.7
180.5
0.99
1.13
2.29
1.84
1.60
200
400
Units Conditions
A
°C
A
A
KA2s
KA2s
180° conduction, half sine wave
DC @ 75°C case temperature
t = 10ms No voltage
t = 8.3ms reapplied
t = 10ms 100% VRRM
t = 8.3ms reapplied Sinusoidal half wave,
t = 10ms No voltage
t = 8.3ms reapplied
Initial TJ = TJ max.
t = 10ms
t = 8.3ms
100% VRRM
reapplied
t = 0.1 to 10ms, no voltage reapplied
(16.7% x π x IT(AV) < I < π x IT(AV)), TJ = TJ max.
V
(I > π x IT(AV)),TJ = TJ max.
(16.7% x π x IT(AV) < I < π x IT(AV)), TJ = TJ max.
m
(I > π x IT(AV)),TJ = TJ max.
V Ipk= 250A, TJ = 25°C tp = 10ms sine pulse
mA TJ = 25°C, anode supply 12V resistive load
2 www.irf.com

No Preview Available !

Switching
Parameter
di/dt Max. non-repetitive rate of rise
of turned-on current
td Typical delay time
tq Typical turn-off time
80RIA Series
Bulletin I25201 rev. B 03/03
80RIA
300
1
110
Units Conditions
A/µs
TJ = 125°C, Vd = rated VDRM, ITM = 2xdi/dt snubber
0.2µF, 15, Gate pulse: 20V, 65, tp = 6µs, tr= 0.5µs
Per JEDEC Standard RS-397, 5.2.2.6.
Gate pulse: 10V, 15source, tp = 6µs, tr = 0.1µs,
µs Vd = rated VDRM, ITM = 50Adc, TJ = 25°C.
ITM = 50A, TJ = TJ max, di/dt = -5A/µs min., VR = 50V,
dv/dt = 20V/µs, Gate bias: 0V 25, tp = 500µs
Blocking
Parameter
dv/dt Maximum critical rate of rise of
off-state voltage
IRRM Max. peak reverse and off-state
IDRM leakage current
80RIA
500
15
Units Conditions
V/µs TJ = 125°C exponential to 67% rated VDRM
mA TJ = 125°C rated VDRM/VRRM applied
Triggering
Parameter
PGM
PG(AV)
IGM
+VGM
Maximum peak gate power
Maximum average gate power
Max. peak positive gate current
Maximum peak positive
gate voltage
-VGM Maximum peak negative
gate voltage
IGT Max. DC gate current required
to trigger
VGT Max. DC gate voltage required
to trigger
IGD DC gate current not to trigger
VGD DC gate voltage not to trigger
80RIA
12
3
3
20
10
270
120
60
3.5
2.5
1.5
6
0.25
Units Conditions
W TJ = TJ max, tp 5ms
TJ = TJ max, f = 50Hz, d% = 50
A TJ = TJ max, tp 5ms
V TJ = TJ max, tp 5ms
TJ = - 40°C
mA TJ = 25°C
TJ = 125°C
TJ = - 40°C
V TJ = 25°C
TJ = 125°C
mA
TJ = TJ max
V
Max. required gate trigger/ cur-
rent/ voltage are the lowest value
which will trigger all units 6V an-
ode-to-cathode applied
Max. gate current/ voltage not to
trigger is the max. value which
will not trigger any unit with rated
VDRM anode-to-cathode applied
www.irf.com
3

No Preview Available !

80RIA Series
Bulletin I25201 rev. B 03/03
Thermal and Mechanical Specification
Parameter
80RIA
Units Conditions
TJ Max. operating temperature range
Tstg Max. storage temperature range
RthJC Max. thermal resistance,
junction to case
RthCS Max. thermal resistance,
case to heatsink
-40 to 125
-40 to 150
0.30
0.1
°C
K/W
DC operation
Mounting surface, smooth, flat and greased
T Mounting torque, ± 10%
15.5 (137)
14 (120)
Nm Non lubricated threads
(lbf-in) Lubricated threads
wt Approximate weight
Case style
130 g
TO-209AC(TO-94)
See Outline Table
RthJ-C Conduction
(The following table shows the increment of thermal resistence RthJ-C when devices operate at different conduction angles than DC)
Conduction angle Sinusoidal conduction Rectangular conduction Units Conditions
180°
120°
90°
60°
30°
0.042
0.050
0.064
0.095
0.164
0.030
0.052
0.070
0.100
0.165
K/W
TJ = TJ max.
Ordering Information Table
Device Code
8 0 RIA 120
1 234
1 - ITAV x 10A
2 - 0 = Eyelet terminals (Gate and Auxiliary Cathode Leads)
1 = Fast - on terminals (Gate and Auxiliary Cathode Leads)
3 - RIA = Essential part number
4 - Voltage code: Code x 10 = VRRM (See Voltage Rating Table)
5 - None = Stud base 1/2"-20UNF- 2A threads
NOTE: For Metric Device M12 x 1.75 E6 Contact factory
4 www.irf.com

No Preview Available !

80RIA Series
Bulletin I25201 rev. B 03/03
Outline Table
GLASS METAL SEAL
16.5 (0.65) MAX.
8.5 (0.3) DIA.
4.3 (0.17) DIA.
2.5 (0.10) MAX.
RED SILICON RUBBER
RED CATHODE
RED SHRINK
FLEXIBLE LEAD
C.S. 16mm 2
(.025 s.i.)
C.S. 0.4 mm 2
(.0006 s.i.)
WHITE GATE
215 (8.46) 10 (0.39)
WHITE SHRINK
23.5 (0.92) MAX. DIA.
Fast-on Terminals
AMP. 280000-1
REF-250
SW 27
1/2"-20UNF-2A *
29.5 (1.16) MAX.
* FOR METRIC DEVICE: M12 X 1.75 E6
CONTACT FACTORY
Case Style TO-209AC (TO-94)
All dimensions in millimeters (inches)
130
80RIA Series
RthJC (DC) = 0.30 K/ W
120
110
Conduc tion Angle
100 30°
60°
90°
90
120°
180°
80
0 10 20 30 40 50 60 70 80 90
Average On-state Current (A)
Fig. 1 - Current Ratings Characteristics
www.irf.com
130
80RIA Series
RthJC (DC) = 0.30 K/ W
120
110
Conduction Period
100
90
30°
60°
80 90°
120°
180°
DC
70
0 20 40 60 80 100 120 140
Average On-state Current (A)
Fig. 2 - Current Ratings Characteristics
5