PP150T120-08.pdf 데이터시트 (총 6 페이지) - 파일 다운로드 PP150T120-08 데이타시트 다운로드

No Preview Available !

TENTATIVE
PP150T120-08
Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272
POW-R-PAKTM
150A / 1200V
Dual 3 phase IGBT Assembly
Description:
The Powerex POW-R-PAKTM is a configurable IGBT
based power assembly that may be used as a
converter, chopper, half or full bridge, or three phase
inverter for motor control, power supply, UPS or other
power conversion applications.
The power assembly is mounted on a forced air-
cooled heatsink and features state-of-the-art Powerex
F-series trench gate IGBTs with low conduction and
switching losses for high efficiency operation. The
POW-R-PAKTM includes a low inductance laminated
bus structure, optically isolated gate drive interfaces,
isolated gate drive power supplies, and a DC-link
capacitor bank. The control board provides a
simple user interface along with built-in
protection features including overvoltage,
undervoltage lockout, overcurrent,
overtemperature, and short circuit detection.
Depending on application characteristics the
POW-R-PAKTM is suitable for operation with DC
bus voltages up to 800VDC and switching
frequencies above 20kHz.
Schematic
Features:
High performance IGBT inverter bridge
Integrated gate drive with fault monitoring
& protection
System status / troubleshooting LEDs to
verify or monitor proper operation
Isolated gate drive power supplies
Low inductance laminated bus
Output current measurement & feedback
Superior short circuit detection & shoot
through prevention
PP150T120-08(-)
-1-

No Preview Available !

TENTATIVE
Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272
Absolute Maximum Ratings, Tj = 25°C unless otherwise specified
General
IGBT Junction Temperature
Storage Temperature
Operating Temperature
Voltage Applied to DC terminals
Isolation Voltage, AC 1 minute, 60Hz sinusoidal
IGBT Inverter
Collector Current (TC = 25°C)
Peak Collector Current (Tj < 150°C)
Emitter Current
Peak Emitter Current
Maximum Collector Dissipation (Tj < 150°C)
Gate Drive Board
Unregulated +24V Power Supply
Regulated +15V Power Supply
PWM Signal Input Voltage
Fault Output Supply Voltage
Fault Output Current
Symbol
Tj
Tstg
Top
VCC
Viso
IC
ICM
IE
IEM
Pc
PP150T120-08
POW-R-PAKTM
150A / 1200V
Dual 3 phase IGBT Assembly
-40 to +150
-40 to +125
-25 to +85
800
2500
150
300
150
300
520
30
18
20
30
50
Units
°C
°C
°C
Volts
Volts
Amperes
Amperes
Amperes
Amperes
Watts
Volts
Volts
Volts
Volts
mA
IGBT Inverter Electrical Characteristics, Tj = 25°C unless otherwise specified
Characteristics
Collector Cutoff Current
Collector – Emitter Saturation Voltage
Emitter – Collector Voltage
Inductive Load Switching Times
Diode Reverse Recovery Time
Diode Reverse Recovery Charge
DC Link Capacitance
Symbol
ICES
VCE(sat)
VEC
td(on)
tr
td(off)
tf
trr
Qrr
Test Conditions
VCE = VCES, VGE = 0V
IC = 150A, Tj = 25°C
IC = 150A, Tj = 125°C
IE = 150A
VCC = 600V
IC = 150A
VGE = 15V
RG = 2.1
Min
-
-
-
-
-
-
-
-
-
-
Typ
-
1.8
1.9
-
-
-
-
-
-
6.0
6600
Max
1
2.4
-
3.2
150
80
450
300
150
-
Units
mA
Volts
Volts
Volts
ns
ns
ns
ns
ns
µC
µF
PP150T120-08(-)
-2-

No Preview Available !

TENTATIVE
PP150T120-08
Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272
POW-R-PAKTM
150A / 1200V
Dual 3 phase IGBT Assembly
Gate Drive Board Electrical Characteristics
Characteristics
Unregulated +24V Power Supply
Regulated +15V Power Supply
PWM Input On Threshold
PWM Input Off Threshold
Output Overcurrent Trip
Overtemperature Trip
Overvoltage Trip
DC Link Voltage Feedback
Heatsink Temperature Feedback
Output Current Feedback
Min Typ
Max
20 24
30
14.4 15
18
12 15
02
225
96 98 100
920
See Figure Below
See Figure Below
See Figure Below
Units
Volts
Volts
Volts
Volts
Amperes
°C
Volts
Volts
Volts
Volts
DC Link Feedback
1000
900
800
700
600
500
400
300
200
100
0
0 1 2 3 4 5 6 7 8 9 10
Feedback Voltage (Volts)
Heatsink Temperature Feedback
120
100
80
60
40
20
0
0 1 2 3 4 5 6 7 8 9 10
Feedback Voltage (Volts)
Output Current Feedback
400
350
300
250
200
150
100
50
0
0 1 2 3 4 5 6 7 8 9 10
Feedback Voltage (Volts)
Thermal and Mechanical Characteristics
Characteristics
IGBT Thermal Resistance, Junction to Case
FWD Thermal Resistance, Junction to Case
Contact Thermal Resistance
Heatsink Thermal Resistance
Mounting Torque, AC terminals
Mounting Torque, DC terminals
Mounting Torque, Mounting plate
Weight
Symbol
Rth(j-c)Q
Rth(j-c)D
Rth(c-f)
Rth(f-a)
Test Conditions
Per IGBT ½ module
Per FWD ½ module
1000 LFM airflow
Min Typ
- 0.11
- 0.020
0.04
75
130
130
21
Max
0.21
0.24
-
90
150
150
Units
°C/W
°C/W
°C/W
°C/W
in-lb
in-lb
in-lb
lb
PP150T120-08(-)
-3-

No Preview Available !

TENTATIVE
PP150T120-08
Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272
POW-R-PAKTM
150A / 1200V
Dual 3 phase IGBT Assembly
Gate Drive Board Interface Signal Definitions
Pin Signal Name
1 Shield
2 PWM A-
3 Phase A Error1
4 PWM A+
5 PWM B-
6 Phase B Error1
7 PWM B+
8 PWM C-
9 Phase C Error1
10 PWM C+
11 Overtemp1
12 Not Connected
13 DC Link Voltage
14 24 VDC input power2
15 24 VDC input power2
16 15 VDC input power2
17 15 VDC input power2
18 GND
19 GND
20 Heatsink Temperature
21 GND3
22 Iout Phase A
23 GND3
24 Iout Phase B
25 GND3
26 Iout Phase C
Description
Connected to circuit ground
0-15 V signal controlling the duty cycle of A- IGBT
Open collector output, external pull-up resistor required
LOW = No Error; Floating = Phase A overcurrent or short circuit
0-15 V signal controlling the duty cycle of A+ IGBT
0-15 V signal controlling the duty cycle of B- IGBT
Open collector output, external pull-up resistor required
LOW = No Error; Floating = Phase B overcurrent or short circuit
0-15 V signal controlling the duty cycle of B+ IGBT
0-15 V signal controlling the duty cycle of C- IGBT
Open collector output, external pull-up resistor required
LOW = No Error; Floating = Phase C overcurrent or short circuit
0-15 V signal controlling the duty cycle of C+ IGBT
Open collector output, external pull-up resistor required
LOW = No Error; Floating = heatsink overtemp
Analog voltage representation of DC link voltage
20 – 30 VDC input voltage range
20 – 30 VDC input voltage range
14.4 – 18 VDC input voltage range
14.4 – 18 VDC input voltage range
Ground reference for 15 and 24 VDC inputs
Ground reference for 15 and 24 VDC inputs
Analog voltage representation of heatsink temperature
Tied to pins 18 and 19
Analog voltage representation of phase A output current
Tied to pins 18 and 19
Analog voltage representation of phase B output current
Tied to pins 18 and 19
Analog voltage representation of phase C output current
Notes:
1.
2.
3.
Open collectors can be pulled up to 30 V max and sink 50mA continuous.
Do not connect a 15 VDC and 24 VDC source to the unit at the same time, use one or the other.
GND signals to be used for analog feedback signals, i.e. twisted pair with Iout Phase A.
Gate Drive Board Interface Connector
Description
Gate Drive Board Interface Header
Recommended Mating Socket
Recommended Strain Relief
Symbol
J1
-
-
Type
0.100” x 0.100” latching header, 26 pin
0.100” x 0.100” IDC socket, 26 pin
Plastic strain relief
Manufacturer
3M# 3429-6002 or equivalent
3M# 3399-7600 or equivalent
3M# 3448-3026 or equivalent
PP150T120-08(-)
-4-

No Preview Available !

TENTATIVE
PP150T120-08
Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272
POW-R-PAKTM
150A / 1200V
Dual 3 phase IGBT Assembly
Performance Curves
Effective Output Current vs. Carrier Frequency (Typical)
140
130
120
110
100
90
80
70
60
50
40
40 60 80 100 120 140 160 180 200 220
Iout ARMS
10kHz
5kHz
1kHz
Condition
Ambient Temperature
DC Bus Voltage
Load Power Factor
IGBT Saturation Voltage
IGBT Switching Loss
Airflow
Switching Conditions
Symbol
Value
TA
VCC
cos φ
40
600
0.8
VCE(sat)
Typical @ TJ = 125°C
ESW Typical @ TJ = 125°C
- 1500
3 phase PWM, 60Hz sinusoidal output
Units
°C
Volts
Volts
mJ
LFM
PP150T120-08(-)
-5-