YC164-xxxx.pdf 데이터시트 (총 6 페이지) - 파일 다운로드 YC164-xxxx 데이타시트 다운로드

No Preview Available !

www.DataSheet4U.com
DATA SHEET
CHIP RESISTORS ARRAY
YC164 (8Pin/4R)
5%; 1%
DataSheet4U.com
DataShee
DataSheet4U.com
DataSheet4 U .com

No Preview Available !

www.DataSheet4U.com
Chip Resistor Surface Mount YC SERIES 164
2
6
SCOPE
This specification describes YC164 series chip resistors made by thick film process.
ORDERING INFORMATION
Part number is identified by the series, size, tolerance, packing style, temperature coefficient, special type and
resistance value.
et4U.com
YC164 – X X X XX XXXX
(1) (2) (3) (4)
(5)
(1) TOLERANCE
F = ±1%
J = ±5%
(2) PACKAGING TYPE
R = Paper taping reel
(3) TEMPERATURE
CHARACTERISTIC OF
RESISTANCE
G = ±200ppm/°C
– = Base on spec
(4) SPECIAL TYPE
07 = 7 inch dia. Reel
(5) RESISTANCE VALUE:
5R6, 56R, 560R, 5K6, 56K, 56M.
MARKING
YC164
ynsc009
Fig. 1 5% Marking, Value=5.6
First two digits for significant figure and
3rd digit for number of zeros
Letter R: decimal place

ynsc010
Fig. 2 Jumper=Zero Ohm
Letter 0: Jumper chip (0 ohm)
DataSheet4U.com
DIMENSION
H
B
a
T
W1
W2
Pa
L
CCB257_a
H2
Fig. 3 YC164 series chip resistors construction
Table 1
TYPE
B (mm)
H (mm)
P (mm)
L (mm)
H2 (mm)
T (mm)
W1 (mm)
W2 (mm)
DataShee
YC164
0.3±0.15
0.65±0.05
0.8±0.05
3.2±0.15
0.5±0.15
0.6±0.1
0.3±0.15
1.6±0.15
DataSheet4U.com
Dec. 20, 2002 V.03
DataSheet4 U .com
SCHEMATIC
For dimension see Fig. 3 and Table 1
Fig. 4 Equivalent circuit diagram
87
handbook, 2 columns
R1 R2
6
R3
5
R4
12
R1=R2=R3=R4
3
CCA862_b
4
www.yageo.com

No Preview Available !

www.DataSheet4U.com
Chip Resistor Surface Mount YC SERIES 164
POWER RATING
RATED POWER AT 70°C,
YC164=1/16W FOR ELEMENT
ndboPomk, ahaxlfpage
(%Prated)
100
MLB206
50
0
55
0 50 70 100 125
Tamb (oC)
Fig. 5
Maximum dissipation (Pmax) in
percentage of rated power as
a function of the operating
ambient temperature (Tamb)
et4U.com
RATED VOLTAGE:
The DC or AC (rms) continuous
working voltage corresponding to
the rated power is determined by
the following formula:
V=(P X R)
Where
V=Continuous rated DC
or AC (rms) working voltage (V)
P=Rated power (W)
R=Resistance value (X)
ELECTRICAL CHARACTERISTICS
Table 2
CHARACTERISTICS
Operating Temperature Range
Maximum Working Voltage
Maximum Overload Voltage
Dielectric Withstanding Voltage
Number of Resistors
Resistance Range
Temperature Coefficient
DataSheet4U.com
3
6
YC164 1/16W
–55°C to +125°C
50V
100V
100V
4
10to 1M
±200ppm/°C
DataShee
DataSheet4U.com
Dec. 20, 2002 V.03
DataSheet4 U .com
www.yageo.com

No Preview Available !

www.DataSheet4U.com
Chip Resistor Surface Mount YC SERIES 164
4
6
TAPING REEL
Table 3
DIMENSION
Tape Width
ØA (mm)
ØB (mm)
ØC (mm)
ØD (mm)
W (mm)
Tmax (mm)
YC164
8mm
180+0/–3
60+1/–0
13.0±0.2
21±0.8
9.0±0.3
11.4±1
For dimension see Table 3
Fig. 6 Reel dimension
gewidth
T
D C BA
MSA284_b
W
et4U.com
PAPER TAPE SPECIFICATION
Table 4
DIMENSION
YC164
A (mm)
2.0±0.1
B (mm)
3.5±0.1
W (mm)
8.0±0.2
E (mm)
1.75±0.1
F (mm)
3.5±0.05
P0 (mm)
P1 (mm)
P2 (mm)
ØD0 (mm)
Tmax (mm)
4.0±0.1
4.0±0.1
2.0±0.05
1.5+0.1/–0
0.85±0.1
P0
D0 P2
DataSheet4U.com B
A
P1
Fig.7 Paper tape dimension
E
F DataShee
W
T
MBD123_a
For dimension see Table 4
PACKING METHOD
LEADER/TRAILER TAPE SPECIFICATION
trailer end
leader end
empty compartments
with cover tape
(min. 240 mm)
cover tape only
trailer (max. 260 mm)
Fig. 8 Leader and trailer tape dimension
Table 5 Packing style and packaging quantity
PACKING STYLE
REEL DIMENSION
Paper Taping Reel (R)
7" (178 mm)
DataSheet4U.com
Dec. 20, 2002 V.03
DataSheet4 U .com
leader 400 mm
YC164
5,000
CCB325
www.yageo.com

No Preview Available !

www.DataSheet4U.com
Chip Resistor Surface Mount YC SERIES 164
5
6
TYPE
Temperature
Coefficient of
Resistance
(T.C.R.)
TEST METHOD
Measure resistance at
+25°C or specified room
temperature as R1, then
measure at –55°C or
+125°C respectively as R2.
Determine the
temperature coefficient of
resistance from the
following formula:
Formula
T.C.R. = -----R---2-–---R---1---------- ×106 (ppm/°C)
R1(t2–t1)
Where
t1=+25°C or specified room temperature
t2=–55°C or +125°C test temperature
R1=resistance at reference temperature in ohms
R2=resistance at test temperature in ohms
ACCEPTANCE STANDARD
Refer to table 2
Thermal
Shock
At –55±3°C for 2 minutes and at +125±2°C for 2 minutes as one cycle. After 5
cycles, the specimen shall be stabilized at room temp.
Measure the resistance to determine ΔR/R(%) after one more hour.
±(1%+0.05)
et4U.com
Low
Temperature
Operation
Place the specimen in a test chamber maintained at –65 (+0/–5)°C. After one hour
stabilization at this temperature, full rated working voltage shall be applied for 45
(+5/–0) minutes. Have15 (+5/–0 ) minutes after remove the voltage, the specimen
shall be removed from the chamber and stabilized at room temperature for 24 hrs.
Measure the resistance to determine ΔDRa/Rta(%S)h. eet4U.com
±(1.0%+0.05)
No visible damage
DataShee
Short
Time
Overload
Apply 2.5 times of rated voltage but not exceeding the maximum overload voltage
for 5 seconds. Have the specimen stabilized at room temperature for 30 minutes
minimum.
Measure the resistance to determine ΔR/R(%).
±(2.0%+0.05)
No visible damage
Insulation
Resistance
Place the specimen in the jig and apply a rated
continues overload voltage (R.C.O.V) for one
minute as shown.
Measure the insulation resistance.
Type
Voltage
YC164
100V
10,000M
Dielectric
Withstand
Voltage
Place the specimen in the jig and apply a
specified value continuous overload voltage as
shown for one minute.
Type
Voltage
YC164
100V
Breakdown voltage>
specification and without
open/short
Resistance
To Soldering
Heat
Immerse the specimen in the solder pot at 260±5°C. for 10±1 seconds. Have the
specimen stabilized at room temperature for 30 minutes minimum.
Measure the resistance to determine ΔR/R(%).
±(1.0%+0.05)
No visible damage
DataSheet4U.com
Dec. 20, 2002 V.03
DataSheet4 U .com
www.yageo.com