T-51863D150J-FW-A-AE.pdf 데이터시트 (총 20 페이지) - 파일 다운로드 T-51863D150J-FW-A-AE 데이타시트 다운로드

No Preview Available !

wwwTyp.eDNoa. taLSCThDe-5e1Mt48oU6d3.cuDol1em5T0eJc-FhWnic-Aa-lASEpecification
First Edition
Dec 10, 2004
Final Revision
******
t4U.comNo. Item
e-- CONTENTS
e1 APPLICATION
h2 OVERVIEW
S3 ABSOLUTE MAXIMUM RATINGS
ta4 ELECTRICAL CHARACTERISTICS
5 INTERFACE PIN CONNECTION
a6 INTERFACE TIMING
.D7 BLOCK DIAGRAM
w8 MECHANICAL SPECIFICATION
9 OPTICAL CHARACTERISTICS
ww10 RELIABILITY TEST CONDITION
Approved by (Quality Assurance Division)
Checked by (ACI Engineering Division)
Prepared by (ACI Engineering Division)
Page
1
2
3
4
4
7
10
15
16
18
20
11 INSPECTION STANDARDS
om12 HANDLING PRECAUTIONS FOR TFT-LCD MODULE
U.c-- PACKAGING SPECIFICATION
t4-- PRODUCTS NUMBER LABELING FORMS
ee-- LAMP UNIT for 15.0”XGA
www.DataShT-51863D150J-FW-A-AE (AE) No. 2004-0161
OPTREX CORPORATION
21
22
25
29
31
Page 1/37

No Preview Available !

1. APPLICATION
This specification applies to color TFT-LCD module, T-51863D150J-FW-A-AE.
These specification papers are the proprietary product of OPTREX and include materials protected
under copyright of OPTREX. No part of this document may be reproduced in any form or by any
means without the express written permission of OPTREX.
OPTREX does not assume any liability for infringement of patents, copyrights or other intellectual
property rights of third parties by or arising from use of a product specified in this document. No
license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual
property rights of OPTREX or of others.
OPTREX classifies the usage of the TFT-LCD module as follows. Please confirm the usage before
using the product.
(1) Standard Usage
Computers, office equipment, factory automation equipment, test and measurement
equipment, communications, transportation equipment(automobiles, ships, trains, etc.),
provided, however, that operation is not influenced by TFT-LCD directly.
(2) Special Usage
Medical equipment, safety equipment, transportation equipment, provided, however, that
TFT-LCD is necessary to its operation.
(3) Specific Usage
Cockpit Equipment, military systems, aerospace equipment, nuclear reactor control systems,
life support systems and any other equipment. OPTREX should make a contract that
stipulate apportionment of responsibilities between OPTREX and our customer.
The product specified in this document is designed for “Standard Usage” unless otherwise specified
in this document. If customers intend to use the product for applications other than those specified
for “Standard Usage”, they should contact OPTREX sales representative in advance.
OPTREX has been making continuous effort to improve the reliability of its products. Customers
should implement sufficient reliability design of their application equipments such as redundant
system design, fail-safe functions, anti-failure features.
OPTREX assumes no responsibility for any damage resulting from the use of the product that does
not comply with the instructions and the precautions specified in this document.
Please contact and consult a OPTREX sales representative for any questions regarding this product.
T-51863D150J-FW-A-AE (AE) No. 2004-0161
OPTREX CORPORATION
Page 2/37

No Preview Available !

2. OVERVIEW
T-51863D150J-FW-A-AE is 15.0” color TFT-LCD (Thin Film Transistor Liquid Crystal Display)
modules composed of LCD panel, driver ICs, control circuit, and backlight unit.
By applying 6 bit or 8 bit digital data, 1024 × 768, 260K-color or 16.7M-color images are displayed on
the 15.0” diagonal screen. Input power voltage is 3.3 V for LCD driving.
The type of data and control signals are digital and transmitted via LVDS interface per Typ. 65 MHz
clock cycle.
Inverter for backlight is not included in this module. General specifications are summarized in the
following table:
ITEM
SPECIFICATION
Display Area (mm)
304.1 (H) × 228.1 (V)
(15.0-inch diagonal)
Number of Dots
1024 × 3 (H) × 768 (V)
Pixel Pitch (mm)
0.297 (H) × 0.297 (V)
Color Pixel Arrangement
RGB vertical stripe
Display Mode
Normally white TN
Number of Color
260K(6 bit/color)16.7M(8 bit/color)
Brightness (cd/m2)
450
Wide Viewing Angle Technology
Optical Compensation Film
Viewing Angle (CR 10)
-75~75° (H) -60~50° (V)
Surface Treatment
Anti-glare and hard-coating 3H
Electrical Interface
LVDS(6 bit/8 bit)
Optimum Viewing Angle (Contrast ratio)
6 o’clock
Module Size (mm)
326.0 (W) × 255.0 (H) × 15.9 (D)
Module Mass (g)
1310
Backlight Unit
CCFL, 4-tubes, edge-light, replaceable
Characteristic value without any note is typical value.
T-51863D150J-FW-A-AE (AE) No. 2004-0161
OPTREX CORPORATION
Page 3/37

No Preview Available !

3. ABSOLUTE MAXIMUM RATINGS
ITEM
SYMBOL
MIN.
MAX.
UNIT
Power Supply Voltage for LCD
VCC
0
4.0
V
Logic Input Voltage
VI
-0.3 VCC+0.3
V
Lamp Voltage
VL
0
2500
Vrms
Lamp Current
IL 0 10.0 mArms
Lamp Frequency
FL --
100 kHz
Operation Temperature(Panel)
Note 1,2)
Top(Panel)
20
70
°C
Operation Temperature(Ambient) Note 2)
Top(Ambient)
20
70
°C
Storage Temperature
Note 2)
Tstg
20
80
°C
[Note]
1) Measured at the center of active area and at the center of panel back surface
2) Top,Tstg 40°C : 90%RH max. without condensation
Top,Tstg > 40°C : Absolute humidity shall be less than the value of 90%RH at 40°C without
condensation.
4. ELECTRICAL CHARACTERISTICS
(1) TFT- LCD
ITEM
SYMBOL MIN.
TYP.
Ambient Temperature : Ta = 25°C
MAX. UNIT
Remarks
Power Supply Voltage for LCD
VCC
3.0 3.3
3.6
V
*1)
Power Supply Current for LCD
ICC
-- 410 700
mA
*2)
Permissive Input Ripple Voltage VRP -- -- 100 mVp-p VCC = +3.3 V
*1) Power and signals sequence:
0.5 t1 10 ms
0 t2 50 ms
0 < t3 50 ms
500 ms t4
200 ms t5
0 t6
0.9VCC
LCD Power Supply
Logic Signal
0.1VCC
VCC
data
0.9VCC
0.1VCC 0.1VCC
Backlight Power Supply
t1 t2
t3 t4
VL
t5 t6
data: RGB DATA, DCLK, HD, VD, DENA
T-51863D150J-FW-A-AE (AE) No. 2004-0161
OPTREX CORPORATION
Page 4/37

No Preview Available !

VCC-dip conditions:
1) When 2.6 V VCC < 3.0 V, td 10 ms
2) When VCC < 2.6 V
VCC-dip conditions should also follow the power and signals sequence.
VCC
td
*2) Typical current condition:
64-gray-bar-pattern(6 bit)
256-gray-bar-pattern(8 bit)
768 line mode
VCC = +3.3 V, fH = 48.4 kHz, fV = 60 Hz, fCLK = 65 MHz
(2) Backlight
ITEM
SYMBOL MIN.
TYP. MAX. UNIT
Ta = 25°C
Remarks
Lamp Voltage
VL
--
620
-- Vrms
IL = 6.5 mArms
Lamp Current
IL 3.5 6.5 8.0 mArms
*1),*5)
Lamp Frequency
FL 40 -- 70 kHz
*2)
1300
--
-- Vrms
Ta = 25°C
Starting Lamp Voltage
VS 1500 --
-- Vrms
Ta = 0°C
1650
--
-- Vrms
Ta = 20°C
Lamp Life Time
LT 50000 --
--
h
*3),*4) IL = 6.5 mArms,
Continuous Operation
*1) Lamp Current measurement method (The current meter is inserted in low voltage line.)
CTL
A
CTL
CTH
A
LCD
Module
CTH
CTL
A
Inverter
Power
Supply
CTL
CTH
A
CTH
*2) Lamp frequency of inverter may produce interference with horizontal synchronous frequency,
and this may cause horizontal beat on the display. Therefore, please adjust lamp frequency, and
keep inverter as far from module as possible or use electronic shielding between inverter and
module to avoid the interference.
*3) Lamp life time is defined as the time either when the brightness becomes 50% of the initial
value, or when the starting lamp voltage does not meet the value specified in this table.
T-51863D150J-FW-A-AE (AE) No. 2004-0161
OPTREX CORPORATION
Page 5/37