C0402Xxxxxx-xxxxxxx.pdf 데이터시트 (총 14 페이지) - 파일 다운로드 C0402Xxxxxx-xxxxxxx 데이타시트 다운로드

No Preview Available !

www.DataSheet4U.com
Ceramic Chip Capacitors
Multilayer chip capacitors have a low residual inductance, an excellent frequency
response and minimal stray capacitance since there are no leads. These characteristics
enable design to be very close to the theoretical values of the capacitors.
NP0/C0G: SPECIFICATIONS:
Typical Capacitance Change vs. Temperature
15%
10%
5%
0%
-5%
-10%
-15%
-55°C -25°C 0°C
25°C 50°C 75°C 100°C 125°C
OPERATING TEMPERATURE RANGE: -55°C to +125°C
TEMPERATURE COEFFICIENT:
0 ±30PPM/°C
TEMPERATURE VOLTAGE COEFFICIENT: 0 ±30PPM/°C
DISSIPATION FACTOR:
0.1% MAX.
INSULATION RESISTANCE:
>1000 ohms F or 100 G ohms, whichever is less at 25°C, VDCW.
(The IR at 125°C is 10% of the value at 25°C)
AGEING:
None
WITHSTANDING VOLTAGE:
>2.5 times VDCW
TEST PARAMETERS:
1MHz ± 100KHz at 1.0 ± 0.2 Vrms 100 pF, 25°C
1KHz ± 100Hz at 1.0 ± 0.2 Vrms > 100 pF, 25°C
CAPACITANCE TOLERANCE:
B,C,D,F,G,J,K
X7R: SPECIFICATIONS:
Typical Capacitance Change vs. Temperature
15%
10%
5%
0%
-5%
-10%
-15%
-55°C -25°C 0°C
25°C 50°C 75°C 100°C 125°C
OPERATING TEMPERATURE RANGE:
TEMPERATURE COEFFICIENT:
TEMPERATURE VOLTAGE COEFFICIENT:
DISSIPATION FACTOR:
INSULATION RESISTANCE:
AGEING:
WITHSTANDING VOLTAGE:
TEST PARAMETERS:*
CAPACITANCE TOLERANCE:
-55°C to +125°C
0 ±15%°C MAX.
X7R not applicable
For 50 volts and 100 volts: 2.5% MAX.;
For 25 volts: 3.0% MAX.; For 16 volts: 3.5% MAX.;
For 10 volts: 5.0% MAX.; For 6.3 volts: 10% MAX.
For values > 10µF and voltages 10V, the D.F. is 10% MAX.
>1000 ohms F or 100 G ohms, whichever is less at 25°C, VDCW.
(The IR at 125°C is 10% of the value at 25°C)
2.5% per decade hour, typical
>2.5 times VDCW
1KHz ± 100Hz at 1.0 ± 0.2 Vrms > 100 pF, 25°C
J,K,M
X5R: SPECIFICATIONS: OPERATING TEMPERATURE RANGE:
www.DataSheet4U.comTEMPERATURE COEFFICIENT:
-55°C to +85°C
0 ±15%°C MAX.
Typical Capacitance Change vs. Temperature
15%
TEMPERATURE VOLTAGE COEFFICIENT: X5R not applicable
DISSIPATION FACTOR:
For 50 volts and 100 volts: 2.5% MAX.;
10% For 25 volts: 3.0% MAX.; For 16 volts: 3.5% MAX.;
5% For 10 volts: 5.0% MAX.; For 6.3 volts: 10% MAX.
0% For values > 10µF and voltages 10V, the D.F. is 10% MAX.
-5%
INSULATION RESISTANCE:
>1000 ohms F or 100 G ohms, whichever is less
at 25°C, VDCW. (10,000 ohms at 125°C)
-10%
AGEING:
2.5% per decade hour, typical
-15%
-55°C -25°C 0°C 25°C 50°C 75°C 100°C 125°C
WITHSTANDING VOLTAGE:
>2.5 times VDCW
TEST PARAMETERS:*
CAPACITANCE TOLERANCE:
1KHZ ± 100Hz at 1.0 ± 0.2 Vrms > 100 pF, 25°C
J,K,M
Z5U: SPECIFICATIONS: OPERATING TEMPERATURE RANGE:
Typical Capacitance Change vs. Temperature
20%
TEMPERATURE COEFFICIENT:
DISSIPATION FACTOR:
0% INSULATION RESISTANCE:
AGEING:
-20%
WITHSTANDING VOLTAGE:
-40% TEST PARAMETERS:
-60% CAPACITANCE TOLERANCE:
+10°C to +85°C
+22% - 56%°C MAX.
4.0% MAX.
>100 ohms F or 10 G ohms, whichever is less at 25°C, VDCW.
5% per decade hour, typical
>2.5 times VDCW
1KHz ± 100Hz at 0.5 ± 0.1 Vrms, 25°C
M,Z,P
-80%
-55°C -25°C 0°C 25°C 50°C 75°C 100°C 125°C
Y5V: SPECIFICATIONS: OPERATING TEMPERATURE RANGE:
Typical Capacitance Change vs. Temperature
40%
TEMPERATURE COEFFICIENT:
DISSIPATION FACTOR:
20%
0%
-20%
-40%
-60%
-80%
-100%
-55°C -25°C
0°C
25°C 50°C 75°C 100°C 125°C
INSULATION RESISTANCE:
AGEING:
WITHSTANDING VOLTAGE:
TEST PARAMETERS:*
CAPACITANCE TOLERANCE:
-30°C to +85°C
+22% - 82%°C MAX.
For 25 volts and 50 volts: 5% MAX.;
For 16 volts: 7% MAX.; For 10 volts: 9% MAX.;
For 6.3 volts: 11% MAX.
For higher Cap values > 10µF, the D.F. is 20% MAX.
>100 ohms F or 10 G ohms, whichever is less at 25°C, VDCW.
7% per decade hour, typical
>2.5 times VDCW
1KHz ± 100Hz at 1.0 ± 0.2 Vrms, 25°C
M,Z
* Test parameters for Hi-Caps: X7R, X5R and Y5V
1KHz ± 100Hz at 1.0 ± 0.2 Vrms 10uF (10 V min.)
1KHz ± 100Hz at 0.5 ± 0.1 Vrms 10uF (6.3V max.)
120Hz ± 24Hz at 0.5 ± 0.1 Vrms > 10uF
6
All components in this section are RoHS compliant per the EU directives and definitions.
www.DataSheet4U.com

No Preview Available !

www.DataSheet4U.com
All tape and reel
specifications must
be adhered to per
EIA-481-1-A as
noted and stated in
the Chip Resistor
section on page 65.
A
B
D
FULL RADIUS
Taping
Specifications
To
T
10 PITCHES
CUMULATIVE
TOLERANCE
D ±0.008
(±0.2 )
Po
Pz
G
N
C
T
E
TAPE
8mm
12mm
B min
0.3
(.012)
0.3
(.012)
Reel Dimensions
C
13 ± .05
(.512 ± .02)
13 ± .05
(.512 ± .02)
A (7")
178 ± 2.0
(7 ± .079)
178 ± 2.0
(7 ± .079)
A (13")
330 ± 2.0
(13 ± .08)
330 ± 2.0
(13 ± .08)
D min
20.2
(.795)
20.2
(.795)
N min
50
(1.97)
50
(1.97)
7 in. Reel Quantities**
Unit: mm (inch)
G
10 ± 1.5
(.394 ± .059)
10 ± 1.5
(.394 ± .059)
T max
14.9
(.587)
14.9
(.587)
SIZE
TAPE SIZE
MIN QTY
PER REEL
01005
8mm
20,000†
0201*
8mm
15,000
0402*
8mm
5000
0603
8mm
3000
0805
8mm
3000
1206
8mm
2000
1210
8mm
1812
12mm
2221
12mm
1000 1000 1000
t TOP TAPE
EMBOSSED
PAPER
DIRECTION OF FEED
Paper Tape
Carrier
Dimensions
(8mm)
A
P
FW
CENTER
OF CAVITY
MAX QTY
PER REEL
20,000† 15,000
10,000
4000
5000
5000 5000
** Quantity dependent on Chip Thickness
* 0201 and 0402 Pitch (“P”) is .079" ± .004" (2.0 ± 0.1mm)
† Smaller quantities may be available. Please contact your sales person.
3000
SIZE
A
B
W
F
E Po Pz
D
01005
0.25 ± 0.05
0.45 ± 0.05
8.0 ± 0.2
(0.010 ± .002) (0.018 ± .002) (.315 ± .008)
3.5 ± 0.1
1.75 ± 0.1
4.0 ± 0.1
(.138 ± .004) (.069 ± .004) (.157 ± .004)
2.0 ± 0.05
(.039 ± .002)
1.5 + 0.1
- 0.0
(.064 + .004)
- .000
0201
0.37 ± 0.05
0.67 ± 0.05
8.0 ± 0.2
(0.014 ± .002) (0.026 ± .002) (.315 ± .008)
3.5 ± 0.1
(.138 ± .004)
1.75 ± 0.1
4.0 ± 0.1
(.069 ± .004) (.157 ± .004)
2.0 ± 0.05
(.039 ± .002)
1.5 + 0.1
- 0.0
(.064 + .004)
- .000
0402
0.65 ± 0.1
(.026 ± .004)
1.10 ± 0.2
(.043 ± .008)
8.0 ± 0.2
(.315 ± .008)
3.5 ± 0.1
(.138 ± .004)
1.75 ± 0.1
4.0 ± 0.1
(.069 ± .004) (.157 ± .004)
2.0 ± 0.05
(.039 ± .002)
1.5 + 0.1
- 0.0
(.064 + .004)
- .000
0603
1.10 ± 0.2
(.043 ± .008)
1.90 ± 0.2
(.075 ± .008)
8.0 ± 0.2
(.315 ± .008)
3.5 ± 0.1
(.138 ± .004)
1.75 ± 0.1
4.0 ± 0.1
(.069 ± .004) (.157 ± .004)
2.0 ± 0.05
(.079 ± .002)
1.5 + 0.1
- 0.0
(.064 + .004)
- .000
1.16 ± 0.2
2.4 ± 0.2
8.0 ± 0.2
3.5 ± 0.1
1.75 ± 0.1
4.0 ± 0.1
2.0 ± 0.05
1.5 + 0.1
0805
- 0.0
( )(.046 ± .008) (.095 ± .008) (.315 ± .008) (.138 ± .004) (.069 ± .004) (.157 ± .004) (.079 ± .002)
.064 + .004
- .000
www.DataSheet4U.com1206
2.0 ± 0.2
3.6 ± 0.2
8.0 ± 0.2
3.5 ± 0.1
1.75 ± 0.1
4.0 ± 0.1
2.0 ± 0.05
1.5 + 0.1
- 0.0
( )(.079 ± .008) (.142 ± .008) (.315 ± .008) (.138 ± .004) (.069 ± .004) (.157 ± .004) (.079 ± .002)
.064 + .004
- .000
t
1.15 MAX
(.045 MAX)
1.15 MAX
(.045 MAX)
1.15 MAX
(.045 MAX)
1.15 MAX
(.045 MAX)
1.15 MAX
(.045 MAX)
1.15 MAX
(.045 MAX)
1000
Unit: mm (inch)
P
2.0 ± 0.05
(.079 ± .002)
2.0 ± 0.05
(.079 ± .002)
2.0 ± 0.05
(.079 ± .002)
4.0 ± 0.1
(.157 ± .004)
4.0 ± 0.1
(.157 ± .004)
4.0 ± 0.1
(.157 ± .004)
Embossed
Carrier
Dimensions
(8mm
& 12mm)
SIZE
0805
1206
1210
1812
A
1.48 ± 0.2
(.058 ± .008)
2.0 ± 0.2
(.079 ± .008)
2.9 ± 0.2
(.114 ± .008)
3.6 ± 0.2
(.142 ± .008)
B
2.3 ± 0.2
(.091 ± .008)
3.6 ± 0.2
(.142 ± .008)
3.6 ± 0.2
(.142 ± .008)
4.9 ± 0.2
(.193 ± .008)
W
8.0 ± 0.2
(.315 ± .008)
8.0 ± 0.2
(.315 ± .008)
8.0 ± 0.2
(.315 ± .008)
12.0 ± 0.3
(.472 ± .012)
F
3.5 ± .0.1
(.138 ± .004)
3.5 ± .0.1
(.138 ± .004)
3.5 ± .0.1
(.138 ± .004)
5.6 ± .0.1
(.221 ± .004)
E
1.75 ± 0.1
Po
4.0 ± 0.1
Pz
2.0 ± 0.05
(.069 ± .004) (.157 ± .004) (.079 ± .002)
1.75 ± 0.1 4.0 ± 0.1 2.0 ± 0.05
(.069 ± .004) (.157 ± .004) (.079 ± .002)
1.75 ± 0.1 4.0 ± 0.1 2.0 ± 0.05
(.069 ± .004) (.157 ± .004) (.079 ± .002)
1.75 ± 0.1 4.0 ± 0.1 2.0 ± 0.05
(.069 ± .004) (.157 ± .004) (.079 ± .002)
D To
1.5 + 0.1 2.5 MAX
- 0.0
( ).06 + .004 (.098 MAX)
- .000
1.5 + 0.1 2.5 MAX
- 0.0
( ).06 + .004 (.098 MAX)
- .000
1.5 + 0.1 2.5 MAX
- 0.0
( ).06 + .004 (.098 MAX)
- .000
1.5 + 0.1 3.8 MAX
- 0.0
( ).06 + .004
- .000
(.150 MAX)
T
0.6 MAX
P
4.0 ± 0.1
(.024 MAX) (.157 ± .004)
0.6 MAX 4.0 ± 0.1
(.024 MAX) (.157 ± .004)
0.6 MAX 4.0 ± 0.1
(.024 MAX) (.157 ± .004)
0.6 MAX 8.0 ± 0.1
(.024 MAX) (.315 ± .004)
How To Order
C0805 C0G
500 —
Series
Temperature Rated Voltage
101
Capacitance
JN
Tolerance Code: Termination
Marking**
P —*
Packaging Optional Identifier
See Chart Characteristic 1st two digits
(pico - Farads)
*B = ± 0.1 pF
N = Nickel Barrier, 6 = EIA “J” Code B = Bulk
are significant
1st two digits
*C = ± 0.25 pF
Tinned Termination “Leave blank if D = Paper Tape ( 10" Reel )
followed by
are significant,
*D = ± 0.5 pF
Composition is
No Marking”
E = Embossed Tape ( 7" Reel )
number of zeroes. followed by
F = ± 1%
100% matte Tin (Sn) P = Paper Tape ( 7" Reel )
6R3 = 6.3 VDCW number of zeroes. G = ± 2%
P = Palladium Silver
R = Paper Tape ( 13" Reel )
100 = 10 VDCW 101 = 100 pF
J = ± 5%
G = Gold over Nickel
U = Embossed Tape ( 13" Reel )
160 = 16 VDCW R denotes decimal K = ± 10%
P: For Palladium Silver Termination (PdAg)
250 = 25 VDCW 6R8 = 6.8 pF
M = ± 20%
add P above.
** 0201 and 0402
500 = 50 VDCW
101 = 100 VDCW
201 = 200 VDCW
251 = 250 VDCW
N = ± 30%
Z = +80 -20%
P = +100 -0%
* For capacitance
Pb: For 90% Tin (Sn)/10% Lead (Pb) Termination
add Pb above.
Standard termination finish for this product is
100% matte Tin (Sn)
size capacitors
cannot be
marked
values below 10 pF only.
* OPTIONAL IDENTIFIER
Min./ Max. thickness
designates minimum thickness
* designates maximum thickness
CODE:
DIMENSION:
The following letters define thickness as signified below:
BCD E F GH I J K LMNOPQR 6 9
.010 .015 .020 .026 .030 .035 .040 .045 .050 .055 .060 .065 .070 .075 .080 .085 .090 .023 .021
Please Note: Venkel offers Engineering Kits for this product. See page 121 for details.
www.DataSheet4U.co7m

No Preview Available !

www.DataSheet4U.com
Ceramic Chip Capacitors
NP0/C0G Dielectric
W
T
L
END
BAND
Values that are typically available.
25V Available in 25V only.
(All measurements in inches)
Size
L
W
T (max)
Min E/B
VDCW (MAX)
0R5 0.5pF
1R0 1.0pF
1R2 1.2
1R5 1.5
1R8 1.8
2R2 2.2
2R7 2.7
3R3 3.3
3R9 3.9
4R7 4.7
5R6 5.6
6R8 6.8
8R2 8.2
100 10pF
120 12
150 15
180 18
220 22
270 27
330 33
390 39
470 47
560 56
680 68
820 82
101 100pF
121 120
151 150
181 180
221 220
271 270
331 330
391 390
471 470
561 560
681 680
821 820
102 1000pF
122 1200
152 1500
182 1800
222 2200
272 2700
332 3300
01005 (± 0.0008)
.016
.008
.008
.002
16V
0201 (± 0.002)
.024
.012
.012
.002
25V
0402 (± 0.004)
.040
.020
.025
.004
25V 50V
0504 (± 0.008)
.050
.040
.040
.005
50V 100V
0603 (± 0.006)
.063
.032
.033
.008
50V 100V
0805 (± 0.008)
.080
.050
.055
.020 ± .010
25V 50V 100V
1206 (± 0.008)
.126
.063
.070
.020 ± .010
50V 100V
1210 (±0.008)
.126
.098
.075
.020 ± .010
50V 100V
1812 (±0.012)
.177
.126
.085
.024 ± .015
50V 100V
www.DataSheet4U.com
Note:
Due to demand and raw material fluctuations in the market, changes and availability of individual values may occur. Minimum order quantities may apply.
8 www.DataSheet4U.com