CP15C.pdf 데이터시트 (총 5 페이지) - 파일 다운로드 CP15C 데이타시트 다운로드

No Preview Available !

CP05
thru
CP24C
STANDARD CAPACITANCE TVS ARRAY
APPLICATIONS
Ethernet - 10 Base T
Cellular Phones
Handheld Electronics
FireWire & USB Interfaces
Multiple I/O Ports or Power Supplie
IEC COMPATIBILITY (EN61000-4)
61000-4-2 (ESD): Air - 15kV, Contact - 8kV
61000-4-4 (EFT): 40A - 5/50ns
61000-4-5 (Surge): 12A, 8/20µs - Level 1(Line-Gnd) & Level 2(Line-Line)
SOT-23-6
FEATURES
200 Watts Peak Pulse Power per Line (tp=8/20µs)
Monolithic Design
Available in Multiple Voltage Types Ranging From 5V to 24V
Protect 4 Bidirectional Lines & 5 Unidirectional Lines
ESD Protection > 25 kilovolts
Low Clamping Voltage
Unidirectional & Bidirectional Configurations
Low Leakage Current
RoHS Compliant
MECHANICAL CHARACTERISTICS
Molded JEDEC SOT-23-6 Package
Weight 16 milligrams (Approximate)
Available in Lead-Free Pure-Tin Plating(Annealed)
Solder Reflow Temperature:
Pure-Tin - Sn, 100: 260-270°C
Consult Factory for Leaded Device Availability
Flammability Rating UL 94V-0
8mm Tape and Reel Per EIA Standard 481
Marking: Marking Code & Pin One Defined By DOT on Package
PIN CONFIGURATIONS
UNIDIRECTIONAL
16
BIDIRECTIONAL
16
25
25
34
34
05133.R8 2/07
1 www.protekdevices.com

No Preview Available !

DEVICE CHARACTERISTICS
MAXIMUM RATINGS @ 25°C Unless Otherwise Specified
PARAMETER
SYMBOL
VALUE
Peak Pulse Power (tp = 8/20µs) - See Figure 1
Operating Temperature
Storage Temperature
PPP 200
TL -55 to 150
TSTG
-55 to 150
CP05
thru
CP24C
UNITS
Watts
°C
°C
PART
NUMBER
(See Notes 1-3)
ELECTRICAL CHARACTERISTICS PER LINE @ 25°C Unless Otherwise Specified
DEVICE
MARKING
RATED
STAND-OFF
VOLTAGE
MINIMUM
BREAKDOWN
VOLTAGE
MAXIMUM
CLAMPING
VOLTAGE
(See Fig. 2)
MAXIMUM
CLAMPING
VOLTAGE
(See Fig. 2)
MAXIMUM
LEAKAGE
CURRENT
VWM
VOLTS
@ 1mA
V(BR)
VOLTS
@ IP = 1A
VC
VOLTS
@8/20µs
VC @ IPP
@VWM
ID
µA
CP05
CP05C
CP12
CP12C
CP15
CP15C
CP24
CP24C
QRH
QRL
QRI
QRM
QRJ
QRN
QRK
QRO
5.0
5.0
12.0
12.0
15.0
15.0
24.0
24.0
6.0
6.0
13.3
13.3
16.7
16.7
26.7
26.7
9.8 11.8V @ 17.0A 20
9.8 11.8V @ 17.0A 20
19 28.3V @ 7.0A
1
19 28.3V @ 7.0A
1
24 45.0V @ 5.0A
1
24 45.0V @ 5.0A
1
43 65.0V @ 3.0A
1
43 65.0V @ 3.0A
1
Note 1: Part numbers with an additional “C” suffix are bidirectional devices, i.e., CP05C.
Note 2: Unidirectional Only: Test between pin 1, 3, 4 and 6 to pin 2 or 5.
Note 3: Bidirectional Only: Test between pin 5 to 1 or 3 or 4 or 6. Electrical characteristics apply in both directions.
TYPICAL
CAPACITANCE
0V @ 1 MHz
Cj
pF
70
70
50
50
30
30
25
25
10000
1000
100
10
0.1
FIGURE 1
PEAK PULSE POWER VS PULSE TIME
200W 8/20µs
Waveform
1 10 100 1000
td - Pulse Duration - µs
FIGURE 2
PULSE WAVE FORM
120
100
tf
Peak Value IPP
TEST
WAVEFORM
PARAMETERS
80 e-t ttfd==82µ0sµs
60
40 td = t IPP/2
20
10000
0
0 5 10 15 20 25 30
t - Time - µs
05133.R8 2/07
2 www.protekdevices.com

No Preview Available !

GRAPHS
100
80
FIGURE 3
POWER DERATING CURVE
Peak Pulse Power
8/20µs
60
40
20
0
0
Average Power
25 50 75 100 125 150
TL - Lead Temperature - °C
CP05
thru
CP24C
FIGURE 4
OVERSHOOT & CLAMPING VOLTAGE FOR CP05
40
30
20
10
0
ESD Test Pulse: 25 kilovolt, 1/30ns (waveshape)
FIGURE 5
16TYPICAL CLAMPING VOLTAGE VS PEAK PULSE CURRENT FOR CP05C
12
8
4
0
0 5 10 15 20
IPP - Peak Pulse Current - Amps
FIGURE 6
TYPICAL REVERSE VOLTAGE VS CAPACITANCE FOR CP05C
80
60
40
20
0
01 2 3 4 5 6
VR - Reverse Voltage - Volts
05133.R8 2/07
3 www.protekdevices.com

No Preview Available !

APPLICATION NOTE
CP05
thru
CP24C
The CP Series are TVS arrays designed to protect I/O or data lines from the damaging effects of ESD or EFT. This product series provides both
unidirectional and bidirectional protection, with a surge capability of 200 Watts PPP per line for an 8/20µs waveform and ESD protection > 25 kilovolts.
UNIDIRECTIONAL COMMON-MODE CONFIGURATION (Figure 1)
The CP Series provides up to four (4) lines of protection in a common-mode configuration as depicted in Figure 1.
Circuit connectivity is as follows:
Line 1 is connected to Pin 1.
Line 2 is connected to Pin 3.
Line 3 is connected to Pin 4.
Line 4 is connected to Pin 6.
Pin 5 is connected to ground.
Pin 2 is not connected.
BIDIRECTIONAL COMMON-MODE CONFIGURATION (Figure 2)
Figure 1 - Unidirectional Configuration
Common-Mode I/O Port Protection
LINE 1
LINE 2
321
The CPxxC Series provides up to four (4) lines of protection in a common-mode
configuration as depicted in Figure 2.
Circuit connectivity is as follows:
Line 1 is connected to Pin 1.
Line 2 is connected to Pin 3.
Line 3 is connected to Pin 4.
Line 4 is connected to Pin 5.
Pin 6 is connected to ground.
Pin 2 is not connected.
456
LINE 3
LINE 4
CIRCUIT BOARD LAYOUT RECOMMENDATIONS
Circuit board layout is critical for Electromagnetic
Compatibility (EMC) protection. The following
guidelines are recommended:
The protection device should be placed near the
input terminals or connectors, the device will
divert the transient current immediately before it
can be coupled into the nearby traces.
The path length between the TVS device and
the protected line should be minimized.
All conductive loops including power and ground
loops should be minimized.
The transient current return path to ground
should be kept as short as possible to reduce
parasitic inductance.
Ground planes should be used whenever
possible. For multilayer PCBs, use ground vias.
Figure 2 - Bidirectional Configuration
Common-Mode I/O Port Protection
LINE 1
LINE 2
321
456
LINE 3
LINE 4
05133.R8 2/07
4 www.protekdevices.com

No Preview Available !

SOT-23-6 PACKAGE OUTLINE & DIMENSIONS
D
E
PACKAGE OUTLINE
CP05
thru
CP24C
SOT-23-6
654
3 21
F
A
TYPICAL
DIM Millimeters Inches
1 0.70 0.028
2 1.90 0.074
3 0.95 0.037
4 2.40 0.094
5 1.00 0.039
K
L
G
C
MOUNTING PAD
0° - 8°
J
BM
4
3
2
1
5
PACKAGE DIMENSIONS
DIM
A
B
C
D
E
F
G
J
K
L
M
MILLIMETERS
MIN MAX
2.80
1.50
0.90
0.35
0.85
1.70
0.90
0.09
2.60
0.20 TYP
0.35
3.05
1.75
1.30
0.50
1.05
2.10
1.45
0.20
3.00
0.20 TYP
0.55
INCHES
MIN MAX
0.110
0.059
0.036
0.014
0.033
0.067
0.036
0.003
0.102
0.007 TYP
0.014
0.120
0.070
0.051
0.020
0.040
0.083
0.057
0.008
0.118
0.007 TYP
0.022
NOTES
1. Dimensioning and tolerances per ANSI Y14.5M, 1985.
2. Controlling Dimension: Inches
3. Dimensions are exclusive of mold flash and metal burrs.
TAPE & REEL/BULK ORDERING NOMENCLATURE
1. Surface mount product is taped and reeled in accordance with EIA-481.
2. Suffix -T7 = 7 Inch Reel - 3,000 pieces per 8mm tape,
i.e., CP05-T7
3. Suffix - LF = Lead-Free, Pure-Tin Plating,
i.e., CP05-LF-T7.
Outline & Dimensions: Rev 2 - 10/05, 06013
Reel Dia. Tape Width
A0
Tape & Reel Specifications (Dimensions in millimeters)
B0 K0 D E F W P0 P2
P tmax
178mm (7”) 8mm 3.20 ± 0.10 3.20 ± 0.10 1.65 ± 0.10 1.50 ± 0.10 1.75 ± 0.10 3.50 ± 0.05 8.00 ±0.30 4.00 ±0.10 2.00 ±0.05 4.00 ±0.10 0.25
P0 10 Pitches Cumulative
D P2 Tolerance on Tape. ± 0.2
t
Top cover tape
K0
A0
B0
Pin 1
Indicated
by Dot
E
F
W
P
User Direction of Feed
COPYRIGHT © ProTek Devices 2007
SPECIFICATIONS: ProTek reserves the right to change the electrical and or mechanical characteristics described herein without notice (except JEDEC).
DESIGN CHANGES: ProTek reserves the right to discontinue product lines without notice, and that the final judgement concerning selection and specifications is
the buyer’s and that in furnishing engineering and technical assistance, ProTek assumes no responsibility with respect to the selection or specifications of such
products.
05133.R8 2/07
5
ProTek Devices
2929 South Fair Lane, Tempe, AZ 85282
Tel: 602-431-8101 Fax: 602-431-2288
E-Mail: sales@protekdevices.com
Web Site: www.protekdevices.com
www.protekdevices.com