IA6008-FA22A.pdf 데이터시트 (총 5 페이지) - 파일 다운로드 IA6008-FA22A 데이타시트 다운로드

No Preview Available !

Contact image sensor heads
IA6008-FA22A
Color image sensor heads for multi-function
IA6008-FA22A
“Color contact image sensor” with optical system intended for Flatbed scanning. Optical technology established for
sheet-feed scanning has been further advanced for Flatbed scanning.
zApplications
Image sensor heads device for multiple function facsimiles such as color scanner and multiple function printer.
zFeatures
1) Signal amplifier is built in to the image sensor IC in order to increase immunity to external noise.
2) Additionally, newly developed analog memory circuit and realizes high speed scanning.
3) The LED light source is mounted on the same substrate as the sensor chip which makes it possible to package the
device with lighter weight and an extremely small size.
4) With the proprietary prism, the output signal is maintained uniformly.
5) The ceramic substrate is used for excellent dimensional accuracy and thermal stability.
zExternal dimensions (Unit : mm)
2−φ 1.5x2
Oval Hole D4MIN
Scanning line
2−φ 1.5 D4MIN
+
236± 0.5
212 (Effective Reading Width)
Effective 1st bit
11.9± 0.8
+
9.4
0.524± 0.1
Dimension of frame
reference surface level.
MAX 2.35
1mm pitch 12pin
Pin No.
No.1
No.2
No.3
No.4
No.5
No.6
Signal
Ao
GND
GND
VDD
GND
SP
Pin No.
No.7
No.8
No.9
No.10
No.11
No.12
Signal
CLK
V-LED
B-GND
G-GND
R-GND
F-GND
No.12 No.1
Center of FCC
13.8
1/4

No Preview Available !

Contact image sensor heads
zCharacteristics
Parameter
Symbol
Typ.
Effective scanning width
212
Primary scan dot density 600
Total dot number
5160
Power supply voltage
VDD 5
Scanning speed
SLT 6.6
Clock frequency
CLK
1.25
Maximum dynamic range
VRmax
0.5
Minimum dynamic range
VRmim.
0.25
Dark output
Vod 1.73 +− 0.45
Operating temperature
5 to 45
Analog signals are output at the double rate of clock frequency.
Unit
mm
dpi
dots
V
ms / line
MHz
V
V
V
°C
zPin assignments
No. Circuit
1 AO
2 GND
3 GND
4 VDD
5 GND
6 SP
7 CLK
8 V-LED
9 B-GND
10 G-GND
11 R-GND
12 F-GND
I / O Function
O Analog output
I Ground
I Ground
I Power supply
I Ground
I Start pulse
I Clock
I LED power supply
I BLUE LED ground
I GREEN LED ground
I RED LED ground
I Frame ground
IA6008-FA22A
2/4

No Preview Available !

Contact image sensor heads
zTiming chart
(a) CLK Timing Chart
CLK
1/fCLK
twCLK twCLK
tSETUP
SP
tHOLD
IA6008-FA22A
ts
Ao
1pixel
2pixel
(b) Data Output Timing Chart
After turning on the SP pulse, the analog output starts from the setting up point of 27 clock pulse.
CLK
123
26 27 28 29
SP
Ao
Note) The CLK section area which is over the effective pixel numbers
(Output blank part) cannot be used as the analog Output standard level.
3/4

No Preview Available !

Contact image sensor heads
zEquivalent circuit
VDD
GND
1µF×2
1
SP
ANALOG MEMORY CIRCUIT
CLK
AO
VLED
IA6008-FA22A
5160
680ohm
1µF
360ohm
VDD
VREF
RGND
GGND
BGND
F-GND
4/4

No Preview Available !

Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document use silicon as a basic material.
Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level of
reliability and the malfunction of with would directly endanger human life (such as medical instruments,
transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other
safety devices), please be sure to consult with our sales representative in advance.
About Export Control Order in Japan
Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control
Order in Japan.
In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause)
on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction.
Appendix1-Rev1.0