MCR006.pdf 데이터시트 (총 5 페이지) - 파일 다운로드 MCR006 데이타시트 다운로드

No Preview Available !

Resistors
Thick film rectangular
MCR006 (0201 size : 1 / 20W)
MCR006
zFeatures
1) Extremely small light
Area ratio is 60% smaller than that of chip 1005, while weight ratio has been cut 80%.
2) Highly reliable chip resistor
Ruthenium oxide dielectric offers superior resistance to the elements.
3) Electrodes not corroded by soldering
Thick film makes the electrodes very strong.
4) Flat surface further facilitates mounting
5) ROHM resistors have approved ISO–9001 certification.
Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the
product before using or ordering it.
zRatings
Item
Rated power
Conditions
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70°C.
100
Specifications
0.05W (1 / 20W)
at 70°C
80
60
40
20
0 55
0 70 100 125
AMBIENT TEMPERATURE (°C)
Fig.1
Rated voltage
The voltage rating is calculated by the following equation.
If the value obtained exceeds the limiting element voltage,
the voltage rating is equal to the maximum operating voltage.
E= P×R
E: Rated voltage (V)
P: Rated power (W)
R: Nominal resistance ()
Nominal resistance
See Table 1.
Operating temperature
Limiting element voltage 25V
55°C to +125°C
1/5

No Preview Available !

Resistors
MCR006
Jumper type
Resistance
Max. 100m
Rated current
0.5A
Operating temperature 55°C to +125°C
Table 1
Resistance tolerance
J (±5%)
F (±1%)
Resistance range
()
10R10M (E24)
100R10M (E24)
Resistance temperature coefficient
(ppm / °C)
±250
±250
zBefore using components in circuits where they will be exposed to transients such as pulse loads (short–duration, high– level loads), be certain to
evaluate the component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with
a steady state voltage that is greater than its rated voltage.
zCharacteristics
Item
Resistance
Variation of resistance
with temperature
Overload
Guaranteed value
Resistor type
Jumper type
J : ±5%
F : ±1%
Max. 100m
See Table.1
Max. 100m
± (2.0%+0.1)
Max. 100m
Solderability
A new uniform coating of minimum of
95% of the surface being immersed
and no soldering damage.
Resistance to
soldering heat
Rapid change of
temperature
Damp heat, steady state
± (1.0%+0.05)
Max. 100m
No remarkable abnormality on the appearance.
± (1.0%+0.05)
Max. 100m
± (3.0%+0.1)
Max. 100m
Endurance at 70°C
± (3.0%+0.1)
Max. 100m
Endurance
Resistance to solvent
Bend strength of
the end face plating
± (3.0%+0.1)
Max. 100m
± (1.0%+0.05)
Max. 100m
± (1.0%+0.05)
Max. 100m
Without mechanical damage such as breaks.
Test conditions (JIS C 5201-1)
JIS C 5201-1 4.5
JIS C 5201-1 4.8
Measurement : +20 / 55 / +20 / +125°C
JIS C 5201-1 4.13
Rated voltage (current) ×2.5, 2s.
Limiting Element Voltage×2 : 50V
JIS C 5201-1 4.17
Rosin·Ethanol (25%WT)
Soldering condition : 235±5°C
Duration of immersion : 2.0±0.5s.
JIS C 5201-1 4.18
Soldering condition : 260±5°C
Duration of immersion : 10±1s.
JIS C 5201-1 4.19
Test temp. : 55°C~+125°C 100cyc
JIS C 5201-1 4.24
40°C, 93%RH
Test time : 1,000h~1,048h
JIS C 5201-1 4.25.1
Rated voltage (current), 70°C±3°C
1.5h : ON 0.5h : OFF
Test time : 1,000h~1,048h
JIS C 5201-1 4.25.3
125°C
Test time : 1,000h~1,048h
JIS C 5201-1 4.29
23±5°C, Immersion cleaning, 5±0.5min.
Solvent : 2-propanol
JIS C 5201-1 4.33
2/5

No Preview Available !

Resistors
zExternal dimensions (Unit : mm)
0.1±0.05
1
0.15±0.05
0.6±0.03
5
MCR006
2
3 No.
Material
1 Thick dielectric glaze of ruthenium (only silver used for jumper)
4
2 Thick film of palladium-silver for primary electrode
3 Nickel-coated secondary electrode
4 External electrode coated with Sn/Pb or Sn
5 Alumina substrate
6 Overcoating (resin)
6
zPackaging
Reel
A BD
C
A
φ180
0
15
B
φ60
+1
0
C
9
+1.0
0
Taping
P0
P2
A0
B0
φD0
E
FW
Label
EIAJ ET-7200A compliant
(Unit : mm)
D
φ13±0.2
P1
Heat crimp cover/Tape
Thick paper
Chip resistor Square press hole
Cover tape
T
Press career tape
Unit mm
W F E A0 B0
8.0±0.2 3.5±0.05 1.75±0.1 0.38±0.03 0.68±0.03
D0
φ1.5
+0.1
0
P0
4.0±0.1
P1 P2
T
2.0±0.05 2.0±0.05 Max. 0.50
3/5

No Preview Available !

Resistors
zPart designation
Part No.
MCR 0 0 6 Y Z P
MCR006
3-digit or 4-digit IEC coding system
Nominal resistance
J
Packaging specifications code
Part No. Code Packaging style Standard ordering unit (pcs)
MCR006 YZP Paper tape
15,000
Resistance tolerance
F ±1% J ±5%
Specify "J" for jumper also.
zDimensions
0.68
0.66
0.64
JIS C 5201-1 4.4.2
SAMPLE SIZE : n=20pcs
MICROMETER
0.62
0.60
0.58
0.56
0.54
0.52
10
100 1k 10k 100k
RESISTANCE ()
1M
Fig.2 Dimensions (length)
0.38
JIS C 5201-1 4.4.2
0.36 SAMPLE SIZE : n=20pcs
MICROMETER
0.34
0.32
0.30
0.28
0.26
0.24
0.22
10 100 1k 10k 100k 1M
RESISTANCE ()
Fig.3 Dimensions (width)
0.31
JIS C 5201-1 4.4.2
0.29 SAMPLE SIZE : n=20pcs
MICROMETER
0.27
0.25
0.23
0.21
0.19
0.17
0.15
10 100 1k 10k 100k 1M
RESISTANCE ()
Fig.4 Dimensions (thickness)
zElectrical characteristics
8.0
JIS C 5201-1 4.5
6.0 SAMPLE SIZE : n=20pcs
20°C 65%RH
4.0
2.0
0
– 2.0
– 4.0
– 6.0
– 8.0
10
100 1k 10k 100k
RESISTANCE ()
1M
Fig.5 Resistance
800
JIS C 5201-1 4.8
600 SAMPLE SIZE : n=10pcs
20°C / 55°C 20°C / 125°C
400
200
0
200
400
600
800
10
100 1k 10k 100k
RESISTANCE ()
1M
Fig.6 Variation of resistance with
temperature
4.0
3.0
2.0
1.0
0.0
1.0
2.0
3.0
4.0
10
JIS C 5201-1 4.13
SAMPLE SIZE : n=10pcs
RATED VOLTAGE × 2.5TIMES : 2s
LIMITING ELEMENT VOLTAGE : 50V
100 1k 10k 100k
RESISTANCE ()
1M
Fig.7 Overload
4/5

No Preview Available !

Resistors
2.0
JIS C 5201-1 4.18
1.5 SAMPLE SIZE : n=10pcs
SOLDERING CONDITION
1.0 : 260°C 10s
0.5
0.0
0.5
1.0
1.5
2.0
10
100 1k 10k 100k
RESISTANCE ()
1M
Fig.8 Resistance to soldering heat
MCR006
2.0
JIS C 5201-1 4.19
1.5 SAMPLE SIZE : n=10pcs
55°C / 125°C 100cyc
1.0
0.5
0
0.5
1.0
1.5
2.0
10
100 1k 10k 100k
RESISTANCE ()
1M
Fig.9 Rapid change of
temperature
4.0
JIS C 5201-1 4.24
3.0 SAMPLE SIZE : n=10pcs
40°C 93%RH WITH NO LOAD
2.0 1000h
1.0
0
1.0
2.0
3.0
4.0
10
100 1k 10k 100k
RESISTANCE ()
1M
Fig.10 Damp heat, steady state
4.0
JIS C 5201-1 4.24
3.0 SAMPLE SIZE : n=10pcs
40°C 93%RH WITH NO LOAD
2.0 1000h
1.0
0
1.0
2.0
3.0
4.0
10
100 1k 10k 100k
RESISTANCE ()
1M
Fig.11 Endurance at 70°C
2.0
1.5
1.0
0.5
0
0.5
1.0
1.5
2.0
10
JIS C 5201-1 4.19
SAMPLE SIZE : n=10pcs
55°C / 125°C 100cyc
100 1k 10k 100k
RESISTANCE ()
Fig.12 Endurance
1M
2.0
JIS C 5201-1 4.29
1.5 SAMPLE SIZE : n=10pcs
IPA, 5min.
1.0
0.5
0
0.5
1.0
1.5
2.0
10
100 1k 10k 100k
RESISTANCE ()
1M
Fig.13 Resistance to solvents
2.0
JIS C 5201-1 4.33
1.5 SAMPLE SIZE : n=10pcs
ENDURANCE WITH 90mm WIDTH
1.0
0.5
0.0
0.5
1.0
1.5
2.0
10 100 1k 10k 100k 1M
RESISTANCE ()
Fig.14 Bend strength of
the end face plating
5/5