CRO2780A.pdf 데이터시트 (총 2 페이지) - 파일 다운로드 CRO2780A 데이타시트 다운로드

No Preview Available !

www.DataSheet4U.com
9939 Via Pasar • San Diego, CA 92126
TEL (858) 621-2700 FAX (858) 621-2722
VOLTAGE CONTROLLED OSCILLATOR
Rev A1
PHASE NOISE (1 Hz BW, typical)
-70
-80
-90
-100
FEATURES
• Frequency Range: 2650 - 2910 MHz
• Tuning Voltage: 0.5-15 Vdc
MINI-16 - Style Package
APPLICATIONS
• Digital Radio Equipment
• Fixed Wireless Access
Satellite Communication Systems
PERFORMANCE SPECIFICATIONS
Oscillation Frequency Range
Phase Noise @ 10 kHz offset (1 Hz BW, typ.)
Harmonic Suppression (2nd, typ.)
Tuning Voltage
Tuning Sensitivity (avg.)
Power Output
Load Impedance
Input Capacitance (max.)
Pushing
Pulling (14 dB Return Loss, Any Phase)
Operating Temperature Range
Package Style
POWER SUPPLY REQUIREMENTS
-110
-120
-130
-140
1000
10000
VALUE
2650 - 2910
-111
-10
0.5-15
20
3±3
50
50
<0.5
<0.5
-40 to 85
MINI-16
Supply Voltage (Vcc, nom.)
10
Supply Current (Icc, typ.)
34
All specifications are typical unless otherwise noted and subject to change without notice.
APPLICATION NOTES
AN-100/1 : Mounting and Grounding of VCOs
AN-102 : Proper Output Loading of VCOs
AN-107 : How to Solder Z-COMM VCOs
NOTES:
100000
UNITS
MHz
dBc/Hz
dBc
Vdc
MHz/V
dBm
pF
MHz/V
MHz
°C
Vdc
mA
© Z-Communications, Inc.
Page 1
All rights reserved

No Preview Available !

LOW COST - HIGH PERFORMANCE
VOLTAGE CONTROLLED OSCILLATOR
2950
TUNING CURVE, typ.
PAGE 2
2900
2850
2800
2750
2700
85 °c
25 °c
-40 °c
2650
2600
0
10
9
8
7
6
5
4
3
2
1
0
-1
-2
2622
123
2662
2695
4 5 6 7 8 9 10 11 12
TUNING VOLTAGE (Vdc)
POWER CURVE, typ.
2725
2754
2783
2811
2840
FREQUENCY (MHz)
2868
13 14 15
2896
2922
25
MINI-16
415-0061 REV. D
(DRAWING NOT TO SCALE)
0.500
0.475
0.405
0.305
0.205
0.105
0.025
0.000
P2
P1=VT
P2=RF OUT
P3=Vcc
P3
BOTTOM VIEW
P1
GROUND PLANE SOLDER PLATED
PHYSICAL DIMENSIONS
TYPICAL OF ALL PADS
SEE NOTE 3
0.415
0.315
DETAIL A
0.215
0.115
SEE DETAIL 'A'
.070
.037
TABS RANGE:
SEE NOTE 5.
(4 PLACES)
.031
.052
.114
.026
.220
.034
0.000
.150
TYP
NOTES:
1. THE INSIDE RADIUS OF ALL 16 HALF HOLES
AT THE PERIMETER OF THE BOARD ARE
PLATED TO PROVIDE A SURFACE FOR THE
ATTACHMENT OF THE VCO TO A PCB,
IN 13 LOCATIONS, WITH 3 PADS BEING
USED FOR ELECTROMECHANICAL INTERFACE.
16 SOLDER LOCATIONS REQUIRED.
2. THE SURFACE OF THE SHIELD IS TIN PLATED
AND MAY BE SOLDERED TO. THE SHIELD'S
BASE METAL IS COLD ROLLED STEEL.
3. THE GROUND PLANE IS GROUND AND ATTACHES
TO A GROUND TRACK ON THE UPPER SIDE OF
THE BOARD AS WELL AS THE SHIELD BY PTH.
4. UNLESS OTHERWISE NOTED ALL DIMENSIONS
ARE IN INCHES.
5. UNLESS OTHERWISE NOTED ALL TOLERANCES
ARE AS FOLLOWS:
TOLERANCES
.XXX= ± .010
.070 TYP
°c
© Z-Communications, Inc.
Page 2
Printed in the U.S.A.