V363ME01-LF.pdf 데이터시트 (총 2 페이지) - 파일 다운로드 V363ME01-LF 데이타시트 다운로드

No Preview Available !

www.DataSheet4U.com
9939 Via Pasar • San Diego, CA 92126
TEL (858) 621-2700 FAX (858) 621-2722
V363ME01-LF
VOLTAGE CONTROLLED OSCILLATOR
Rev A1
PHASE NOISE (1 Hz BW, typical)
-70
-80
-90
-100
-110
FEATURES
• Frequency Range: 362 - 364
• Tuning Voltage: 0.5-4.5 Vdc
• MINI-16 - Style Package
APPLICATIONS
MHz
-120
-130
-140
-150
1 E+3
10 E+3
OFFSET (Hz)
100 E+3
PERFORMANCE SPECIFICATIONS
Oscillation Frequency Range
Phase Noise @ 10 kHz offset (1 Hz BW, typ.)
Harmonic Suppression (2nd, typ.)
Tuning Voltage
Tuning Sensitivity (avg.)
VALUE
362 - 364
-118
-12
0.5-4.5
15
UNITS
MHz
dBc/Hz
dBc
Vdc
MHz/V
Power Output
Load Impedance
5±1.5
50
dBm
Input Capacitance (max.)
50 pF
Pushing
Pulling (14 dB Return Loss, Any Phase)
Operating Temperature Range
Package Style
<3
<1
-40 to 85
MINI-16
MHz/V
MHz
°C
POWER SUPPLY REQUIREMENTS
Supply Voltage (Vcc, nom.)
5.5 Vdc
Supply Current (Icc, typ.)
23
All specifications are typical unless otherwise noted and subject to change without notice.
mA
APPLICATION NOTES
AN-100/1 : Mounting and Grounding of VCOs
AN-102 : Proper Output Loading of VCOs
AN-107 : How to Solder Z-COMM VCOs
NOTES:
© Z-Communications, Inc.
Page 1
All rights reserved

No Preview Available !

LOW COST - HIGH PERFORMANCE
VOLTAGE CONTROLLED OSCILLATOR
V363ME01-LF
PAGE 2
390
385
380
375
370
365
360
355
350
345
340
335
0
8
7
6
5
4
3
2
1
0
341
TUNING CURVE, typ.
0.5 1 1.5 2 2.5 3 3.5 4 4.5
TUNING VOLTAGE (Vdc)
POWER CURVE, typ.
350
359
367
374
380
386
MINI-16
415-0061 REV. D
(DRAWING NOT TO SCALE)
0.500
0.475
0.405
0.305
0.205
0.105
0.025
0.000
P2
P1=VT
P2=RF OUT
P3=Vcc
P3
BOTTOM VIEW
P1
GROUND PLANE SOLDER PLATED
FREQUENCY (MHz)
PHYSICAL DIMENSIONS
TYPICAL OF ALL PADS
SEE NOTE 3
0.415
0.315
DETAIL A
0.215
0.115
SEE DETAIL 'A'
.070
.037
TABS RANGE:
SEE NOTE 5.
(4 PLACES)
.031
.052
.114
.026
.220
.034
0.000
.150
TYP
NOTES:
1. THE INSIDE RADIUS OF ALL 16 HALF HOLES
AT THE PERIMETER OF THE BOARD ARE
PLATED TO PROVIDE A SURFACE FOR THE
ATTACHMENT OF THE VCO TO A PCB,
IN 13 LOCATIONS, WITH 3 PADS BEING
USED FOR ELECTROMECHANICAL INTERFACE.
16 SOLDER LOCATIONS REQUIRED.
2. THE SURFACE OF THE SHIELD IS TIN PLATED
AND MAY BE SOLDERED TO. THE SHIELD'S
BASE METAL IS COLD ROLLED STEEL.
3. THE GROUND PLANE IS GROUND AND ATTACHES
TO A GROUND TRACK ON THE UPPER SIDE OF
THE BOARD AS WELL AS THE SHIELD BY PTH.
4. UNLESS OTHERWISE NOTED ALL DIMENSIONS
ARE IN INCHES.
5. UNLESS OTHERWISE NOTED ALL TOLERANCES
ARE AS FOLLOWS:
TOLERANCES
.XXX= ± .010
.070 TYP
°c
°c
°c
°c
© Z-Communications, Inc.
Page 2
Printed in the U.S.A.