AZ10E116.pdf 데이터시트 (총 5 페이지) - 파일 다운로드 AZ10E116 데이타시트 다운로드

No Preview Available !

www.DataSheet4U.com
ARIZONA MICROTEK, INC.
AZ10E116
AZ100E116
ECL/PECL Quint Differential Line Receiver
FEATURES
PACKAGE AVAILABILITY
500ps Maximum Propagation Delay
PACKAGE PART NUMBER MARKING NOTES
Dedicated VCCO Pin for Each Receiver
Operating Range of 4.2V to 5.46V
PLCC 28
AZ10E116FN
AZM10E116
<Date Code>
1,2
75kΩ Internal Input Pulldown Resistors
PLCC 28
Direct Replacement for ON Semiconductor
AZ100E116FN
AZM100E116
<Date Code>
1,2
MC10E116 & MC100E116
1 Add R2 at end of part number for 13 inch (2.5K parts) Tape & Reel.
2 Date code format: “YY” for year followed by “WW” for week.
DESCRIPTION
The AZ10/100E116 is a quint differential line receiver with emitter-follower outputs. The E116 provides a VBB
output for single-ended use or a DC bias reference for AC coupling to the device. For single-ended input
applications, the VBB reference should be connected to one side of the Dn/D¯ n differential input pair. The input
signal is then fed to the other Dn/D¯ n input. The VBB pin should be used only as a bias for the E116 as its sink/source
capability is limited. When used, the VBB pin should be bypassed to ground via a 0.01μF capacitor.
The receiver design features clamp circuitry to cause a defined state if both the inverting and non-inverting
inputs are left open; in this case the Q output goes LOW, while the Q¯ output goes HIGH. This feature makes the
device ideal for twisted pair applications.
If both inverting and non-inverting inputs are at an equal potential of > VCC -2.5V, the receiver does not go
to a defined state. This condition may produce output voltage levels between HIGH and LOW.
NOTE: Specifications in ECL/PECL tables are valid when thermal equilibrium is established.
1630 S. STAPLEY DR., SUITE 127 MESA, ARIZONA 85204 USA (480) 962-5881 FAX (480) 890-2541
www.azmicrotek.com

No Preview Available !

AZ10E116
AZ100E116
D3 D4 D4 VCCO Q4 Q4 VCCO
25 24 23 22 21 20 19
D3 26
18
D2 27
17
Q3
Q3
D2 28
V1
EE
VBB 2
D0 3
D0 4
5
Pinout: 28-lead
PLCC (top view)
16
15
14
13
12
6 7 8 9 10 11
VCC
Q2
Q2
VCCO
Q1
D1 D1 VCCO Q0 Q0 VCCO Q1
PIN DESCRIPTION
PIN
D0, D¯¯0 -D4, D¯¯4
Q0, Q¯¯0-Q4, Q¯¯4
VBB
VCC , VCCO
VEE
FUNCTION
Differential Input Pairs
Differential Output Pairs
Reference Voltage Output
Positive Supply
Negative Supply
LOGIC SYMBOL
D0 Q0
D0 Q0
D1 Q1
D1 Q1
D2 Q2
D2 Q2
D3 Q3
D3 Q3
D4
D4
VBB
Q4
Q4
Absolute Maximum Ratings are those values beyond which device life may be impaired.
Symbol
Characteristic
Rating
VCC PECL Power Supply (VEE = 0V)
VI PECL Input Voltage (VEE = 0V)
VEE ECL Power Supply (VCC = 0V)
VI ECL Input Voltage (VCC = 0V)
IOUT
Output Current
--- Continuous
--- Surge
0 to +8.0
0 to +6.0
-8.0 to 0
-6.0 to 0
50
100
TA Operating Temperature Range
TSTG Storage Temperature Range
-40 to +85
-65 to +150
Unit
Vdc
Vdc
Vdc
Vdc
mA
°C
°C
10K ECL DC Characteristics (VEE = -4.94V to -5.46V, VCC = VCCO = GND)
Symbol
Characteristic
-40°C
0°C
Min Typ Max Min Typ Max Min
VOH Output HIGH Voltage1 -1080
VOL Output LOW Voltage1 -1950
-890 -1020
-1650 -1950
-840 -980
-1630 -1950
VIH
Input HIGH Voltage
-1230
-890 -1170
-840 -1130
VIL
Input LOW Voltage
-1950
-1500 -1950
-1480 -1950
VBB
Reference Voltage
-1430
-1300 -1380
-1270 -1350
IIH Input HIGH Current
150 150
IIL
Input LOW Current
0.5
0.5
0.5
IEE Power Supply Current
29 35
29 35
1. Each output is terminated through a 50Ω resistor to VCC – 2V.
25°C
Typ
29
Max
-810
-1630
-810
-1480
-1250
150
35
Min
-910
-1950
-1060
-1950
-1310
0.5
85°C
Typ
29
Max
-720
-1595
-720
-1445
-1190
150
35
Unit
mV
mV
mV
mV
mV
μA
μA
mA
November 2006 * REV - 3
www.azmicrotek.com
2

No Preview Available !

AZ10E116
AZ100E116
10K PECL DC Characteristics (VEE = GND, VCC = VCCO = +5.0V)
Symbol
Characteristic
-40°C
0°C
Min Typ Max Min Typ Max Min
VOH Output HIGH Voltage1,2 3920
VOL
Output LOW Voltage1,2
3050
VIH
Input HIGH Voltage1
3770
VIL Input LOW Voltage1 3050
VBB Reference Voltage1
3570
4110
3350
4110
3500
3700
3980
3050
3830
3050
3620
4160
3370
4160
3520
3730
4020
3050
3870
3050
3650
IIH Input HIGH Current
150 150
IIL Input LOW Current
0.5
0.5
0.5
IEE Power Supply Current
29 35
29 35
1. For supply voltages other that 5.0V, use the ECL table values and ADD supply voltage value.
2. Each output is terminated through a 50Ω resistor to VCC – 2V.
25°C
Typ
29
Max
4190
3370
4190
3520
3750
150
35
Min
4090
3050
3940
3050
3690
0.5
85°C
Typ
29
Max
4280
3405
4280
3555
3810
150
35
Unit
mV
mV
mV
mV
mV
μA
μA
mA
100K ECL DC Characteristics (VEE = -4.2V to -5.46V, VCC = VCCO = GND)
Symbol
Characteristic
-40°C
0°C
Min Typ Max Min Typ Max Min
VOH Output HIGH Voltage1 -1085 -1005 -880 -1025 -955 -880 -1025
VOL Output LOW Voltage1 -1830 -1695 -1555 -1810 -1705 -1620 -1810
VIH
Input HIGH Voltage
-1165
-880 -1165
-880 -1165
VIL
Input LOW Voltage
-1810
-1475 -1810
-1475 -1810
VBB
Reference Voltage
-1380
-1260 -1380
-1260 -1380
IIH Input HIGH Current
150 150
IIL
Input LOW Current
0.5
0.5
0.5
IEE Power Supply Current
29 35
29 35
1. Each output is terminated through a 50Ω resistor to VCC – 2V.
25°C
Typ
-955
-1705
29
Max
-880
-1620
-880
-1475
-1260
150
35
Min
-1025
-1810
-1165
-1810
-1380
0.5
85°C
Typ
-955
-1705
29
Max
-880
-1620
-880
-1475
-1260
150
40
Unit
mV
mV
mV
mV
mV
μA
μA
mA
100K PECL DC Characteristics (VEE = GND, VCC = VCCO = +5.0V)
Symbol
Characteristic
-40°C
0°C
Min Typ Max Min Typ Max Min
VOH Output HIGH Voltage1,2 3915 3995 4120 3975 4045 4120 3975
VOL
Output LOW Voltage1,2
3170 3305 3445 3190 3295 3380 3190
VIH
Input HIGH Voltage1
3835
4120 3835
4120 3835
VIL Input LOW Voltage1 3190
3525 3190
3525 3190
VBB Reference Voltage1
3620
3740 3620
3740 3620
IIH Input HIGH Current
150 150
IIL Input LOW Current
0.5
0.5
0.5
IEE Power Supply Current
29 35
29 35
1. For supply voltages other that 5.0V, use the ECL table values and ADD supply voltage value.
2. Each output is terminated through a 50Ω resistor to VCC – 2V.
25°C
Typ
4045
3295
Max
4120
3380
4120
3525
3740
150
29 35
Min
3975
3190
3835
3190
3620
0.5
85°C
Typ
4045
3295
29
Max
4120
3380
4120
3525
3740
150
40
Unit
mV
mV
mV
mV
mV
μA
μA
mA
AC Characteristics (VEE =10E(-4.94V to -5.46V), 100E(-4.2V to -5.46V); VCC =VCCO =GND or VEE=GND,
VCC=VCCO =10E(+4.94V to +5.46V),100E(+4.2V to +5.46V) )
Symbol
Characteristic
-40°C
0°C
25°C
85°C
Unit Condition
Min Typ Max Min Typ Max Min Typ Max Min Typ Max
Propagation Delay to
tPLH /tPHL
Output
D (Differential)
150
300
500
200
300
450
200
300
450
200
300
450
ps
D (Single-Ended) 150 300 550 150 300 500 150 300 500 150 300 500
TSKEW
Within-Device Skew1
50
50
50
50 ps
TSKEW
Duty Cycle Skew2
tPLH - tPHL
±10
±10
±10
±10 ps
Vpp(AC) Minimum Input
Swing3
150
150
150
150
mV
VCMR
Common Mode
Range4
VCC
- 2.0
VCC
VCC
- 0.6 - 2.0
VCC
VCC
- 0.6 - 2.0
VCC
VCC
- 0.6 - 2.0
VCC
- 0.6
V
tr/tf Rise/Fall Time
250
625 275
575 275
575 275
575 ps
20-80%
1. Within-device skew is defined as identical transitions on similar paths through a device.
2. Duty cycle skew is defined only for differential operation. The skews are measured from the crossover point of the inputs to the crossover point
of the outputs.
3. VPP is the minimum peak-to-peak differential input swing for which AC parameters are guaranteed.
4. The VCMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within
the specified range and the peak-to-peak voltage lies between VPP (min) and 1V.
November 2006 * REV - 3
www.azmicrotek.com
3

No Preview Available !

AZ10E116
AZ100E116
PACKAGE DIAGRAM
PLCC 28
DIM
A
B
C
E
F
G
H
J
K
R
U
V
W
X
T
Z
G1
K1
MILLIMETERS
MIN MAX
12.32 12.57
12.32 12.57
4.20 4.57
2.29 2.79
0.33 0.48
1.27 BSC
0.66 0.81
0.51
0.64
11.43 11.58
11.43 11.58
1.07 1.21
1.07 1.21
1.07 1.42
0.50
2O 10O
10.42 10.92
1.02
INCHES
MIN MAX
0.485 0.495
0.485 0.495
0.165 0.180
0.090 0.110
0.013 0.019
0.050 BSC
0.026 0.032
0.020
0.025
0.450 0.456
0.450 0.456
0.042 0.048
0.042 0.048
0.042 0.056
0.020
2O 10O
0.410 0.430
0.040
NOTES:
1. DATUMS –L-, -M-, AND –N- DETERMINED
WHERE TOP OF LEAD SHOULDER EXITS
PLASTIC BODY AT MOLD PARTING LINE.
2. DIMENSION G1, TRUE POSITION TO BE
MEASURED AT DATUM –T-, SEATING PLANE.
3. DIMENSIONS R AND U DO NOT INCLUDE
MOLD FLASH. ALOWABLE MOLD FLASH IS
0.010mm (0.250in.) PER SIDE.
4. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
5. CONTROLLING DIMENSION: INCH.
6. THE PACKAGE TOP MAY BE SMALLER THAN
THE PACKGE BOTTOM BY UP TO 0.012mm
(0.300in.). DIMENSIONS R AND U ARE
DETERMINED AT THE OUTERMOST
EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, THE BAR
BURRS, GATE BURRS AND INTERLEAD FLASH,
BUT INCLUDING ANY MISMATCH BETWEEN
THE TOP AND BOTTOM OF THE PLASTIC
BODY.
7. DIMENSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H
DIMENSION TO BE SMALLER THAN 0.025mm
(0.635in.).
November 2006 * REV - 3
www.azmicrotek.com
4

No Preview Available !

AZ10E116
AZ100E116
Arizona Microtek, Inc. reserves the right to change circuitry and specifications at any time without prior notice. Arizona Microtek, Inc.
makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Arizona
Microtek, Inc. assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all
liability, including without limitation special, consequential or incidental damages. Arizona Microtek, Inc. does not convey any license
rights nor the rights of others. Arizona Microtek, Inc. products are not designed, intended or authorized for use as components in systems
intended to support or sustain life, or for any other application in which the failure of the Arizona Microtek, Inc. product could create a
situation where personal injury or death may occur. Should Buyer purchase or use Arizona Microtek, Inc. products for any such
unintended or unauthorized application, Buyer shall indemnify and hold Arizona Microtek, Inc. and its officers, employees, subsidiaries,
affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly
or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Arizona Microtek, Inc. was negligent regarding the design or manufacture of the part.
November 2006 * REV - 3
www.azmicrotek.com
5