U0805FxxxxxT.pdf 데이터시트 (총 19 페이지) - 파일 다운로드 U0805FxxxxxT 데이타시트 다운로드

No Preview Available !

www.DataSheet4U.com
Nickel Barrier
Multilayer Ceramic Capacitors
Features:
Multilayer ceramic chip capacitor.
Nickel barrier termination.
High performance and reliability.
0603, 0805, and 1206 case size.
Rated Voltage
Code
Rated Voltage
A
B
T
U
Part Dimension
100
16
25
50
Length
(L)
1.6 ±0.1
2.0 ±0.2
3.2 ±0.2
Width
(W)
Maximum
Thickness
(T)
0.8 ±0.1
1.25 ±0.1
1.40
1.60 ±0.2
1.52
Dimensions
Minimum
MB
0.20
0.25
Minimum
G
0.40
0.70
1.40
Voltage
(V)
6.3 ~ 50
6.3 ~ 500
6.3 ~ 1000
Type
0603
0805
1206
Page 1
27/04/06 V1.0

No Preview Available !

www.DataSheet4U.com
Nickel Barrier
Multilayer Ceramic Capacitors
Temperature Characteristics Code
Code
Temperature Coefficient
Operation Temperature
(°C)
C NPO (Class I)
R X7R (Class II)
-55°C ~ +125
F Y5V (Class II)
30°C ~ +85
Capacitance Change
0 ±30ppm/°C
±15%
+22% ~ -82%
Capacitance Code
Code
010
Capacitance
(pF)
1*
1R5 1.5
100 10*
101 100*
102 1000*
103 10000*
222 2200*
472 4700*
Tolerance Code
Code
Tolerance
(%)
J ±5
K ±10
Z +80/-20
PS:
· * -- Two significant digits followed by number of zeros.
· Temperature coefficient (T.C.) vs. Proper tolerance applied:
NPO:
For all tolerance
X7R+X5R:
K+M Tolerance
Y5V+Z5U:
M+Z Tolerance
Termination Code
Code
N
Termination Type
Nickel
Packaging Code
Code
Packaging Type
BT
Bulk Tape and Reel
Standard Test Conditions
Tests shall, unless otherwise specified, be carried out at 15 to 35°C and RH 45 to 75%.If any doubt and argument has been
encounter in judgement, the final test shall be done at 25 ±2°C, RH45 to 55% and 860 ~ 1060mbar. (Based on JIS standard).
Disposition
If question to the measuring result in judgement, take the capacitor under a specified temperature for 30 minutes at least before
measurement.
Page 2
27/04/06 V1.0

No Preview Available !

www.DataSheet4U.com
Nickel Barrier
Multilayer Ceramic Capacitors
Structure
Ag/Pd Series
Number
1
2
3
4
5
Specifications
Ceramic Dielectric
Internal Electrode
End Terminal
Material
Ceramic
Ag-Pd
Ag layer
Ni layer
Sn-Pb layer or Sn layer
Minimum Termination
Plating Thickness
(µ m)
40
1.5 - 3.5
3-8
BME Series
Number
1
2
3
4
5
Specifications
Ceramic Dielectric
Internal Electrode
End Termination
Material
Ceramic
Ni
Cu layer
Ni layer
Sn-Pb layer or Sn layer
Minimum Termination
Plating Thickness
(µ m)
40
1.5 - 3.5
3-8
Storing Condition And Term
Recommends the storing of products within 6 months at temperature 15 ~ 35°C and humidity 70%RH maximum. If the product stored
over 6 months, please reconfirm its solderability before use.
Page 3
27/04/06 V1.0

No Preview Available !

www.DataSheet4U.com
Nickel Barrier
Multilayer Ceramic Capacitors
Performance
Item
External
Appearance
Voltage Proof
Performance
Test or Inspection Method
No defects which may affect
performance
Visual inspection and dimension measurement
DC Tested voltage shall be applied for 1 ~ 5 second.
Charge/discharge current shall not exceed 50mA (PS : Ra
- Rated Voltage)
Withstand test voltage without insulation
breakdown or other damage
Code
200V
250V
500V/630V
1KV
Temperature Coefficient
NPO
1.5Ra
X7R/X5R
2.5Ra
2.0Ra
1.5Ra
1.25Ra
Y5V
-
Insulation Resistance
Capacitance
(Cap.)
Dissipation Factor (D.F)
NPO:
100,000Mminimum or R x C 1000x
F (Which ever is smaller)
X7R, X5R, Y5V, Z5U:
10,000Mminimum or R x C 1000x
F (Which ever is smaller)
Rated Voltage
DC Tested Voltage
<1KV
1.0 Ra
1KV
1KV
Apply DC tested voltage for 60 ±5 minute.
(PS : Ra - Rated Voltage)
Within the specified tolerance
NPO:
30pF: Q 1000
<30pF: Q 400 + 20C
PS:C: Nominal Capacitance (pF)
X7R, X5R, Y5V, and Z5U : (Maximum
Value)
T.C.
X7R/
X5R
Z5U
50V
25V
16V 10V
2.5% 3.0% 3.5% 5.0%
4.0% - - -
Measuring Frequency:
Z5U,Y5V, X7R, X5R : 1KHz ±50Hz
NPO:
>1000pF:1KHz ±50Hz.
1000pF:1MHz 100KHz.
Measuring Voltage:
Z5U:0.5Vrms.
NPO:
X7R, X5R, Y5V:1.0 ±0.2Vrms.
Y5V 5.0% 7.5% 9.0% 12.5%
Page 4
27/04/06 V1.0

No Preview Available !

www.DataSheet4U.com
Nickel Barrier
Multilayer Ceramic Capacitors
Item
Performance
Test or Inspection Method
Temperature
Characteristic
of Capacitance
Temperatures Coefficient
TC
Operating
Temperature
NPO -55 ~ +125°C
X7R -55 ~ +125°C
X5R -55 ~ +85°C
Y5V -55 ~ +125°C
Z5U -55 ~ +125°C
Capacitance
Change (DC)
0 ±30 (ppm/°C)
±15%
±15%
+22% ~ -82%
+22% ~ -56%
The temperature coefficient is determined using the
capacitance measured in step 3 as a reference. Test the
specimen from step 1through step 5, the capacitance shall
be within the specified tolerance for the capacitance
coefficient and capacitance change as left table.
Code
1
2
3
Temperature Coefficient
Base Temperature (25°C) ±2°C
Minimum Operation Temperature ±2°C
Base Temperature (25°C) ±2°C
4 Minimum Operation Temperature ±2°C
5 Base Temperature (25°C) ±2°C
Solderabiliy
New solder to over 95% of termination
Leaching
External
Appearance
No mechanical Damage
Completely soak both terminal electrodes in
solder at specified temperature for 3 ±0.5 second
a. For Tin-Lead Sn/Pb) Termination product:
235 ±5°C.
b. For Lead-free (Pure Sn) Termination
product: 245 ±5°C.
Completely soak both terminal electrodes in solder at 270
±5°C for 40 ±1second.
NPO
Capacitance
Change
(C/C)
X7R/X5
R
Z5U
Y5V
±2.5% or ±0.25 pF maximum
(Whichever is larger)
±7.5%
±20%
±20%
Soldering
to heat
NPO: C 30pF : Q 1000
C<30pF:Q 400 + 20°C
PS: C : Nominal Capacitance (pF)
X7R, X5R, Y5V, Z5U : (Maximum Value)
DF
T.C.
50V
25V
16V 10V
X7R/
X5R
2.5% 3.0% 3.5% 5.0%
Z5U 4.0% - - -
Y5V 5.0% 7.5% 9.0% 12.5%
Completely immerse both
terminations in solder at 270 ±5°C for 10 ±3 second.
Leave the capacitors in ambient condition for 2 4 ±2 hours
before measurement.
*Preconditioning: F(only for Class 2):
Perform a heat treatment at 150 +0-10°C for one hour and
then let sit for 24 ±2 hours at room temperature.
Perform the initial measurement.
NPO:
100,000MW minimum or R x C 1000W
IR
x F (Whichever is smaller)
X7R, X5R, Y5V, Z5U:
10,000MW minimum or R x C 1000W
x F (Whichever is smaller)
Page 5
27/04/06 V1.0