E13C9.pdf 데이터시트 (총 3 페이지) - 파일 다운로드 E13C9 데이타시트 다운로드

No Preview Available !

Marketing Bulletin
DATE: March 24th, 2006
TO: All Sales Personnel
FROM:
www.DataSheet4U.com
RE:
Mark Stoner
Product Termination
To all concerned parties,
This bulletin is to notify all customers of the discontinuation of the following Ecliptek
series effective March 24th, 2006:
Series
E13C9
Description
Recommended Replacement
3.3V 5 x 7mm SMD LVPECL Oscillator E13C7 or E13D8
In compliance with our End of Life (EOL) policy, this will serve as advanced notice of
product termination. New orders will not be accepted after July 1st, 2006, with delivery to
conclude by October 1st 2006.
If there are any questions pertaining to this bulletin, please fell free to contact me.
Thank you again for your cooperation.
Best Regards,
Mark W. Stoner
Director of Marketing
Ecliptek Corporation
3545 CADILLAC AVENUE COSTA MESA, CA 92626-1401 (714) 433-1200 Fax (714) 433-1234

No Preview Available !

E13C9 Series
• RoHS Compliant (Pb-Free)
• LVPECL Output Oscillators
• 3.3V Supply Voltage
• AT-Cut Fundamental Mode Inverted Mesa Crystal
• Ceramic 6-pad SMD Package
• Stability to 25ppm
• Tri-State Enable High and Enable Low Options
Available on Pad 1 or Pad 2
• Complementary Output
www.DataSheet4U.coWm ide Range of Available Frequencies
ELECTRICAL SPECIFICATIONS
E13C9
H 2.0
L 7.0
W 5.0
OSCILLATOR
OBSOLETE
Nominal Frequency
Operating Temperature Range
Storage Temperature Range
Supply Voltage (VCC)
Input Current
Frequency Tolerance / Stability
Output Voltage Logic High (VOH)
Output Voltage Logic Low (VOL)
Rise Time / Fall Time
Duty Cycle
Inclusive of All Conditions: Calibration Tolerance at 25°C,
Frequency Stability over the Operating Temperature Range,
Supply Voltage Change, Output Load Change, 1st Year
Aging at 25°C, Shock, and Vibration
20% to 80% of waveform
at 50% of waveform
Load Drive Capability
Logic Control / Additional Output
Enable High or Enable Low
Enable High Tri-State Input Voltage VIH of 70% of VCC Minimum
No Connection
Enable Low Tri-State Input Voltage
VIL of 30% of VCC Maximum
VIH of 70% of VCC Minimum
No Connection
Output Disable Current
VIL of 30% of VCC Maximum
Start Up Time
RMS Phase Jitter
Phase Noise (at 155.520MHz)
< 44.736MHz; FJ = 12kHz to 20MHz
> 44.736MHz, < 77.760MHz; FJ = 12kHz to 20MHz
> 77.760MHz; FJ = 12kHz to 20MHz
at 10Hz Offset
at 100Hz Offset
at 1kHz Offset
at 10kHz Offset
at 100kHz Offset
19.440MHz to 200.000MHz
0°C to 70°C, or -40°C to +85°C
-55°C to 125°C
3.3VDC ±5%
75mA Maximum
±100ppm, ±50ppm, or
±25ppm Maximum
VCC-1.025VDC Minimum
VCC-1.620VDC Maximum
1.5 nSeconds Maximum, 600 pSec Typical
50 ±10(%)
50 ±5(%)
50 Ohms into VCC-2.0VDC
No Connect and Complementary Output or
Tri-State and Complementary Output
Enables Output
Enables Output
Disables Output: High Impedance
Disables Output: High Impedance
Enables Output
Enables Output
25mA Maximum
10 mSeconds Maximum
5 pSec Maximum
2 pSec Maximum
1 pSec Maximum
-75dBc/Hz Typical
-95dBc/Hz Typical
-125dBc/Hz Typical
-140dBc/Hz Typical
-145dBc/Hz Typical
MANUFACTURER
ECLIPTEK CORP.
CATEGORY
OSCILLATOR
SERIES
E13C9
PACKAGE
CERAMIC
VOLTAGE
3.3V
CLASS
OS1T
REV.DATE
06/04
800-ECLIPTEK www.ecliptek.com for latest revision
Specifications subject to change without notice.

No Preview Available !

OBSOLETE PART NUMBERING GUIDE
FREQUENCY TOLERANCE & STABILITY/
OPERATING TEMPERATURE RANGE
C=±100ppm Maximum over 0°C to +70°C
D=±50ppm Maximum over 0°C to +70°C
E=±25ppm Maximum over 0°C to +70°C
G=±100ppm Maximum over -40°C to +85°C
H=±50ppm Maximum over -40°C to +85°C
J=±25ppm Maximum over -40°C to +85°C
DUTY CYCLE
1=50% ±10%, 2=50% ±5%
E13C9 E 2 F - 155.520M TR
AVAILABLE OPTIONS
Blank=Tubes
TR=Tape and Reel (Standard)
FREQUENCY
LOGIC CONTROL/ADDITIONAL OUTPUT
C=No Connect and Complementary Output
F=Tri-State (Enable High) on Pad 1 and Complementary Output
H=Tri-State (Enable High) on Pad 2 and Complementary Output
J=Tri-State (Enable Low) on Pad 1 and Complementary Output
K=Tri-State (Enable Low) on Pad 2 and Complementary Output
www.DataSheetM4EUC.HcoAmNICAL DIMENSIONS
ALL DIMENSIONS IN MILLIMETERS
SUGGESTED SOLDER PAD LAYOUT
ALL DIMENSIONS IN MILLIMETERS
Pin 1: Tri-State or No Connect Pin 4: Output
Pin 2: Tri-State or No Connect Pin 5: Complementary Output
Pin 3: Case Ground
Pin 6: Supply Voltage
TAPE AND REEL DIMENSIONS
ALL DIMENSIONS IN MILLIMETERS
Tolerances= +0.1
TAPE
A
B
C
D EF
16±.3-.1 7.5±.1 6.75±.1 4 ±.1
2±.1
F
GH
JK L
8±.1 B0* 1.5 +.1-0 A0* .3 ±.05 K0*
ENVIRONMENTAL/MECHANICAL SPECIFICATIONS
Characteristic
Fine Leak Test
Gross Leak Test
Mechanical Shock
Vibration
Solderability
Temperature Cycling
Resistance to Soldering Heat
Resistance to Solvents
Specification
MIL-STD-883, Method 1014, Condition A
MIL-STD-883, Method 1014, Condition C
MIL-STD-202, Method 213, Condition C
MIL-STD-883, Method 2007, Condition A
MIL-STD-883, Method 2002
MIL-STD-883, Method 1010
MIL-STD-202, Method 210
MIL-STD-202, Method 215
REEL
R
2.5 MIN
M
1.5 MIN
S
10 MIN
N
50 MIN
T
22.4 MAX
O
20.2 MIN
U
360 MAX
P
13±.2
V
16.4+2-0
Q
40 MIN
QTY/REEL
1,000
*Compliant to EIA 481A
MARKING SPECIFICATIONS
Line 1: ECLIPTEK
Line 2: XX.XXX M
Frequency in MHz (5 Digits Maximum + Decimal)
Line 3: XX Y ZZ
Week of Year
Last Digit of Year
Ecliptek Manufacturing Identifier
MANUFACTURER
ECLIPTEK CORP.
CATEGORY
OSCILLATOR
SERIES
E13C9
PACKAGE
CERAMIC
VOLTAGE
3.3V
CLASS
OS1T
REV.DATE
06/04
800-ECLIPTEK www.ecliptek.com for latest revision
Specifications subject to change without notice.