MB95156M.pdf 데이터시트 (총 30 페이지) - 파일 다운로드 MB95156M 데이타시트 다운로드

No Preview Available !

FUJITSU SEMICONDUCTOR
DATA SHEET
DS07-12613-3E
8-bit Microcontroller
CMOS
F2MC-8FX MB95150M Series
www.DataSheetM4U.coBm 95156M/F156M/F156N/F156J/FV100D-103
DESCRIPTION
The MB95150M series is general-purpose, single-chip microcontrollers. In addition to a compact instruction set,
the microcontrollers contain a variety of peripheral functions.
Note : F2MC is the abbreviation of FUJITSU Flexible Microcontroller.
FEATURE
F2MC-8FX CPU core
Instruction set optimized for controllers
• Multiplication and division instructions
• 16-bit arithmetic operations
• Bit test branch instruction
• Bit manipulation instructions etc.
Clock
• Main clock
• Main PLL clock
• Sub clock
• Sub PLL clock
(Continued)
Be sure to refer to the “Check Sheet” for the latest cautions on development.
“Check Sheet” is seen at the following support page
URL : http://www.fujitsu.com/global/services/microelectronics/product/micom/support/index.html
“Check Sheet” lists the minimal requirement items to be checked to prevent problems beforehand in system
development.
Copyright©2006-2007 FUJITSU LIMITED All rights reserved

No Preview Available !

MB95150M Series
(Continued)
Timer
• 8/16-bit compound timer × 2 channels
Can be used to interval timer, PWC timer, PWM timer and input capture.
• 8/16-bit PPG × 2 channels
• 16-bit PPG × 1 channel
• Time-base timer × 1 channel
• Watch prescaler × 1 channel
LIN-UART × 1 channel
• LIN function, clock asynchronous (UART) or clock synchronous (SIO) serial data transfer capable
www.DataSheet4U.comFull duplex double buffer
UART/SIO × 1 channel
• Clock asynchronous (UART) or clock synchronous (SIO) serial data transfer capable
• Full duplex double buffer
External interrupt × 8 channels
• Interrupt by edge detection (rising, falling, or both edges can be selected)
• Can be used to recover from low-power consumption (standby) modes.
8/10-bit A/D converter × 8 channels
8-bit or 10-bit resolution can be selected.
LCD controller (LCDC)
• 16 SEG × 4 COM (Max 64 pixels)
• With blinking function
Low-power consumption (standby) mode
• Stop mode
• Sleep mode
• Watch mode
• Time-base timer mode
I/O port: Max 39
• General-purpose I/O ports (CMOS) : 39 ports
Programmable input voltage levels of port
Automotive input level / CMOS input level / hysteresis input level
Flash memory security function
Protects the content of Flash memory (Flash memory device only)
2

No Preview Available !

MB95150M Series
PRODUCT LINEUP
Part number
Parameter
MB95156M
Type
MASK ROM product
MB95F156M
MB95F156N
Flash memory product
MB95F156J
ROM capacity
32 Kbytes
RAM capacity
1 Kbyte
Reset output
Yes/No
Yes
No
Clock system
www.DataSheet4U.coLmow voltage
detection reset
Yes/No
Dual clock
No
Yes
Clock supervisor
Yes/No
No
Yes
CPU functions
Number of basic instructions
: 136
Instruction bit length
: 8 bits
Instruction length
: 1 to 3 bytes
Data bit length
: 1, 8, and 16 bits
Minimum instruction execution time : 61.5 ns (at machine clock frequency 16.25 MHz)
Interrupt processing time
: 0.6 µs (at machine clock frequency 16.25 MHz)
General-purpose I/O port (CMOS) : 39 ports
Ports (Max 39 ports) Programmable input voltage levels of port :
Automotive input level / CMOS input level / hysteresis input level
Time-base timer
(1 channel)
Interrupt cycle : 0.5 ms, 2.1 ms, 8.2 ms, 32.8 ms (at main oscillation clock 4 MHz)
Watchdog timer
Reset generated cycle
At main oscillation clock 10 MHz : Min 105 ms
At sub oscillation clock 32.768 kHz : Min 250 ms
Wild register
Capable of replacing 3 bytes of ROM data
UART/SIO
(1 channel)
Data transfer capable in UART/SIO
Full duplex double buffer, variable data length (5/6/7/8-bit), built-in baud rate
generator
NRZ type transfer format, error detected function
LSB-first or MSB-first can be selected.
Clock asynchronous (UART) or clock synchronous (SIO) serial data transfer capable
LIN-UART
(1 channel)
Dedicated reload timer allowing a wide range of communication speeds to be set.
Full duplex double buffer
Clock asynchronous (UART) or clock synchronous (SIO) serial data transfer capable
LIN functions available as the LIN master or LIN slave.
8/10-bit A/D converter
(8 channels)
8-bit
or
10-bit
resolution
can
be
selected.
LCD controller
(LCDC)
COM output
: 4 (Max)
SEG output
: 16 (Max)
LCD drive power supply (bias) pin : 4
16 SEG × 4 COM
: 64 pixels can be displayed.
Duty LCD mode
Operable in LCD standby mode
With blinking function
Built-in division resistance for LCD drive
(Continued)
3

No Preview Available !

MB95150M Series
(Continued)
Part number
Parameter
MB95156M
MB95F156M
MB95F156N
MB95F156J
8/16-bit compound
timer (2 channels)
Each channel of the timer can be used as “8-bit timer × 2 channels” or “16-bit timer
× 1 channel”.
Built-in timer function, PWC function, PWM function, capture function, and square
waveform output
Count clock : 7 internal clocks and external clock can be selected.
16-bit PPG
www.DataSheet4U.co(m1 channel)
PWM mode or one-shot mode can be selected.
Counter operating clock : Eight selectable clock sources
Support for external trigger start
8/16-bit PPG
(2 channels)
Each channel of the PPG can be used as 8-bit PPG × 2 channelsor 16-bit PPG ×
1 channel.
Counter operating clock : Eight selectable clock sources
Watch counter
Watch prescaler
(1 channel)
Count clock : Four selectable clock sources (125 ms, 250 ms, 500 ms, or 1 s)
Counter value can be set from 0 to 63. (Capable of counting for 1 minute when
selecting clock source 1 second and setting counter value to 60)
4 selectable interval times (125 ms, 250 ms, 500 ms, or 1 s)
External interrupt
(8 channels)
Interrupt by edge detection (rising, falling, or both edges can be selected.)
Can be used to recover from standby modes.
Flash memory
Supports automatic programming, Embedded AlgorithmTM *2
Write/Erase/Erase-Suspend/Resume commands
A flag indicating completion of the algorithm
Number of write/erase cycles (Minimum) : 10000 times
Data retention time : 20 years
Boot block configuration
Erase can be performed on each block
Block protection with external programming voltage
Flash Security Feature for protecting the content of the Flash
Standby mode
Sleep, stop, watch, and time-base timer
*1 : For details of option, refer to “MASK OPTION”.
*2 : Embedded Algorithm is a trade mark of Advanced Micro Devices Inc.
Note : Part number of evaluation products in MB95150M series is MB95FV100D-103. When using it, the MCU
board (MB2146-303A) is required.
4

No Preview Available !

MB95150M Series
OSCILLATION STABILIZATION WAIT TIME
The initial value of the main clock oscillation stabilization wait time is fixed to the maximum value. The maximum
value is shown as follows.
Oscillation stabilization wait time
(2142) /FCH
Remarks
Approx. 4.10 ms (at main oscillation clock 4 MHz)
PACKAGES AND CORRESPONDING PRODUCTS
www.DataSheet4U.com
Package
Part number MB95156M
MB95F156M/F156N/F156J
FPT-48P-M26
FPT-52P-M01
BGA-224P-M08
: Available
: Unavailable
MB95FV100D-103
5