T0810.pdf 데이터시트 (총 9 페이지) - 파일 다운로드 T0810 데이타시트 다운로드

No Preview Available !

T0810
3-Channel Laser Driver with RF Osc. and APC Amplifier
Description
www.datashTeehte4uT.c0o8m10 is a laser diode driver for the operation of a
grounded laser diode for CD-RW drives. It includes three
channels for three different optical power levels which
are controlled by a separate IC. The read channel gener-
ates a continuous output level whereas the channels 2 and
3 are provided as write channels with very fast switching
speeds. Write current pulses are enabled when a ‘low’
signal is applied to the NE Pins. All channels are summed
together at the IOUT Pin. Each channel can contribute up
to 150 mA to the total output current of up to 200 mA. A
total gain of 400 mA is provided between each reference
current input and output. Although the reference inputs
are current inputs, voltage control is possible by using
external resistors.
An on-chip RF oscillator is provided to reduce laser mode
hopping noise during read mode. Frequency and swing
can be set by two external resistors. Oscillation is enabled
by a ‘high’ at the ENOSC Pin. Complete output current
and oscillator switch-off is achieved by a ‘low’ at the
ENABLE input.
The T0810 also includes a fast settling APC (Adaptive
Power Control) transimpedance amplifier. It is provided
to interface between the front end monitor photo diode
and the ALPC (Adaptive Laser Diode Power Controller)
circuit.
Electrostatic sensitive device.
Observe precautions for handling.
Features
D Current-controlled output current source with 3 input
channels
D Low-power consumption
D Output current per channel to 150 mA
D Total output current to 200 mA
D Rise time 1.0 ns / fall time 1.1 ns
D On-chip RF oscillator
D Control of frequency and swing by use of 2 external
resistors
D Oscillator frequency range from 200MHz to 500 MHz
D Oscillator swing to 100 mA
D Fast settling APC amplifier
D Single 5-V power supply
D Common enable / disable input
D TTL/CMOS control signals
D Small SSO16 package
Application
D CD-RW drives
D Writable optical drives
Block Diagram
PDIN
VREF
APC
VOUT
I3
NE3 Channel 3
I2
NE2 Channel 2
IR
ENABLE
Read
channel
ENOSC
RF oscillator
RF RS
Figure 1. Block diagram
IOUT
Rev. A5, 08-Aug-01
1 (9)

No Preview Available !

T0810
Ordering Information
Extended Type Number
T0810-TCQ
www.datasheet4u.com
SSO16
Package
Pin Description
Pin Symbol
Function
1 VOUT APC amplifier output
2 VREF Reference voltage input
3 IR Inp. current, bias voltage approx. GND
4 RF External resistor to GND sets
oscillator frequency
5 I2 Inp. current, bias voltage approx. GND
6 I3 Inp. current, bias voltage approx. GND
7 NE2 Digital control of channel 2
(low active)
8 NE3 Digital control of channel 3
(low active)
9 VCC + 5 V power supply
10 ENOSC Enables RF oscillator (high active)
11 ENABLE Enables output current (high active)
12 RS External resistor to GND sets
oscillator swing
13 GND Ground
14 IOUT Output current source for laser diode
15 VCC + 5 V power supply
16 PDIN Photo diode input
Remarks
Taped and reeled
VOUT 1
16 PDIN
VREF 2
15 VCC
IR 3
14 IOUT
RF 4
I2 5
T0810
13 GND
12 RS
I3 6
11 ENABLE
NE2 7
10 ENOSC
NE3 8
9 VCC
Figure 2. Pinning SSO16
Absolute Maximum Ratings
Parameter
Supply voltage
Input voltage at IR, I2, I3
Input voltage at NE2, NE3, ENOSC
Output voltage
Power dissipation
Junction temperature
Storage temperature range
1) RthJA 80 K/W
Symbol
VCC
VIN1
VIN2
VOUT
PMAX
TJ
TSTG
Value
–0.5 to +6.0
–0.5 to + 0.5
–0.5 to VCC + 0.5
–0.5 to VCC –1
1 1)
150
–65 to +125
Unit
V
V
V
V
W
_C
_C
2 (9) Rev. A5, 08-Aug-01

No Preview Available !

T0810
Thermal Resistance
Parameter
Junction ambient
www.datasheet4u.com
Recommended Operating Conditions
Parameter
Supply voltage range
Input current
External resistor to GND to set oscillator frequency
External resistor to GND to set oscillator swing
Operating temperature range
Symbol
RthJA
Symbol
VCC
IIR/II2/II3
RF
RS
Tamb
Value
150
Value
4.5 to 5.5
< 0.4
>3
> 100
0 to +70
Unit
K/W
Unit
V
mA
k
_C
Electrical Characteristics : General
VCC = 5 V, Tamb =25_C, ENABLE = High, NE2 = NE3 = High, ENOSC = Low, unless otherwise specified
Parameter
Test Conditions / Pins Symbol Min. Typ. Max. Unit
Power supply
Supply current, power down ENABLE = Low,
NE2 = NE3 = Low
ICCPD
0.2 0.4 mA
Supply current, read mode,
Oscillator disabled
Supply current, read mode,
Oscillator enabled
Supply current, write mode
Supply current, input off
Digital inputs
IIR = II2 = II3 = 125 µA
ICCR1
IIR = II2 = II3 = 125 µA,
ENOSC = High, RS = 560 ,
RF = 6.8 k
IIR = II2 = II3 = 125 µA,
NE2 = NE3 = Low
IIR = II2 = II3 = 0 µA
ICCR2
ICCW
ICCoff
90 107 mA
100 118 mA
190 220 mA
15 20 mA
NE2/NE3 low voltage
NE2/NE3 high voltage
ENABLE low voltage
ENABLE high voltage
ENOSC low voltage
ENOSC high voltage
Current at digital inputs
NE2/NE3 low current
NE2/NE3 high current
ENABLE low current
ENABLE high current
ENOSC low current
ENOSC high current
NE = 0 V
NE = 5 V
ENABLE = 0 V
ENABLE = 5 V
ENOSC = 0 V
ENOSC = 5 V
VNELO
VNEHI
VENLO
VENHI
VEOLO
VEOHI
2.0
3.0
2.0
INELO
INEHI
IENLO
IENHI
IEOLO
IEOHI
–300
–150
–100
1.3 V
V
0.5 V
V
0.5 V
V
µA
800 µA
µA
100 µA
µA
800 µA
Rev. A5, 08-Aug-01
3 (9)

No Preview Available !

T0810
Electrical Characteristics : Laser Amplifier
VCC = 5 V, Tamb = 25_C, ENABLE = High, unless otherwise specified
Parameter
Test Conditions / Pins
Symbol
www.datBasehset efti4tuc.ucorrment gain
Any channel 1)
GAIN
Best fit current offset
Any channel 1)
IOS
Output current linearity
Any channel 1)
ILIN
Input current range
Input is sinking
IDAC
Output current per channel
Total output current
IOUT series resistance
IIN input impedance
NE threshold
Output is sourcing
IOUT = 180 mA total
ROUT to VCC – Rail
RIN is to GND
Temperature stabilized
IOUTR
IOUT
ROUT
RIN
VTH
Output off current 1
Output off current 2
Output off current 3
IOUT supply sensitivity,
read mode
IOUT supply sensitivity,
write mode
IOUT current output noise
IOUT temperature sensitivity,
read mode
ENABLE = Low
NE2 = NE3 = High,
IIR = 0, II2 = II3 = 125 µA
NE2 = NE3 = Low,
IIR = II2 = II3 = 0 µA
IOUT = 40 mA,
VCC = 5 V ± 10%, read only
IOUT = 80 mA, 40 mA read +
40 mA write, VCC = 5 V ± 10%
IOUT = 40 mA, ENOSC = Low
IOUT = 40 mA, read only
IOFF1
IOFF2
IOFF3
VSER
VSEW
INOO
TSER
IOUT temperature sensitivity, IOUT = 80 mA, 40 mA read +
write mode
40 mA write
TSEW
Min.
–8
–3
0
150
200
1200
–4
–6
Typ.
400
8
2000
1.68
3
100
100
Max.
+4
+3
0.4
Unit
mA/mA
mA
%
mA
mA
mA
2500
0.5
0.7
V
mA
mA
5 mA
1 %/V
0 %/V
nA/rt–Hz
ppm/°C
ppm/°C
1) Linearity of the amplifier is calculated using a best fit method at three operating points of
IOUT at 20 mA, 40 mA, and 60 mA. IOUT = (IIN GAIN) + IOS
4 (9) Rev. A5, 08-Aug-01

No Preview Available !

T0810
Electrical Characteristics :
Laser Current Amplifier Outputs AC Performance
VCC = + 5 V, IOUT = 40 mA DC with 40 mA pulse, TA = 25°C unless otherwise specified
www.datasheet4u.com Parameter
Test Conditions / Pins
Symbol Min. Typ.
Max.
Unit
Write rise time
Write fall time
Output current overshoot
IOUT ON propagation delay
IOFF OFF propagation delay
Disable time
Enable time
Amplifier bandwidth
Oscillator
Oscillator frequency
Osc. temperature coefficient
Disable time oscillator
Enable time oscillator
IOUT = 40 mA (read) + 40 mA
(10% to 90%) 1)
IOUT = 40 mA (read) + 40 mA
(10% to 90%) 1)
IOUT = 40 mA (read) + 40 mA 1)
NE 50% High–Low to IOUT at
50% of final value
NE 50% Low–High to IOUT at
50% of final value
ENABLE 50% High–Low to
IOUT at 50% of final value
ENABLE 50% Low–High to
IOUT at 50% of final value
IOUT = 50 mA, all channels,
–3dB value
tRISE
tFALL
OS
tON
tOFF
tDIS
tEN
BWLCA
RF = 4.3 k
RF = 4.3 k
ENOSC 50% High–Low to IOUT
at 50% of final value
ENOSC 50% Low–High to IOUT
at 50% of final value
FOSC
TCOSC
TDISO
TENO
380
1.0
1.4
5
2.0
2.0
10
50
16
470
–150
4
2
3.0 ns
3.0 ns
%
ns
ns
ns
ns
MHz
560 MHz
ppm/°C
ns
ns
1) Load resistor at IOUT: 10 // 39 + 50 (see test circuit)
Electrical Characteristics : APC Amplifier
VCC = 5 V, TA = 25°C, RLOAD = 2 kto VREF unless otherwise specified
Parameter
Test Conditions / Pins Symbol Min.
Typ.
Max.
Unit
Bandwidth
Slew rate
Setting time
Open loop voltage gain
Offset voltage
Input bias current
Common mode input range
G = 1, Cload = 22 pF
G = 1, VOUT = 1 V to 3 V
To 0.1%, VOUT = 1 V to 3 V
VOUT = 1 V to 3 V
VREF = 3 V
VREF = 3 V
CMRR > = 54 dB
BWAPC
SR
ts
Avol
VOS
CMIR
Common mode rejection ratio VCM = 0.5 V to 3.0 V
Input impedance
Input capacitance
Pin 16 (PDIN)
Output voltage swing
RL = 2 kto VREF
CMRR
RIN
CIN
VOUT
–5
1
1
200 MHz
80 V/µs
50 ns
60 dB
+5 mV
–1.5 µA
VCC–1.5 V
60 dB
20 k
2 pF
VCC–1.5 V
Rev. A5, 08-Aug-01
5 (9)