AEH60K48.pdf 데이터시트 (총 2 페이지) - 파일 다운로드 AEH60K48 데이타시트 다운로드

No Preview Available !

60Amps
AEH60
Total Power:
Input Voltages:
No. of Outputs:
200 Watts (3.3V @ 60A)
48 V
Single
ALH60 (Open Frame)
Ultra High Efficiency Half Brick
Electrical Specs
Input
Input range
Input Surge
Efficiency
36-75 VDC
100V / 100ms
91% @ 3.3V (Typical)
Control
Enable
TTL compatible
(positive or negative enable logic
control options)
Special Features
• High efficiency, 3.3V@ 91% (Typical)
• Baseplate (AEH) or Open frame (ALH) design
• Low output ripple and noise
• High capacitive load limit on start-up
• Remote sense compensation
• Regulation to zero load
• Fixed frequency switching
• Industry Std features: Input UVLO, OCP, OVP,
OTP; Short ckt protection; ±10% Output Adjust
• Positive or Negative enable logic control option
• Meets Basic Insulation
Output
Regulation
(Line, Load, Temp)
Ripple and Noise1
Remote Sense
Output Voltage Adjust
Range
Transient Response
Overv Voltage
Protection
Over Current
Protection
Over Temperature
Protection
Isolation Voltage
<2%
2% typical (100mVp-p max)
Up to 10%Vout
±10% of nominal output
60mV typical output deviation
25% step change
150 µS recovery time
135% nominal output (latching)
115% of full load (latching)
Shutdown - autorecovery mode
1500 Vdc
Environmental
Operating temperature
-40°C to +100°C Baseplate (AEH60)
-40°C to +85°C Ambient (ALH60)
Storage temperature: -55°C to +125°C
Overtemperature protection: 115°C PCB
Temperature (Typical)
MTBF: >1 million hours
Safety
UL, cUL 60950 Recognized
TUV EN60950 Licensed
2 North America (USA): 1-888-41-ASTEC Europe (UK): 44 (1384) 842-211Asia (HK): 852-2437-9662

No Preview Available !

AMERICAS
5810 Van Allen Way
Carlsbad, CA 92008
Telephone: 760-930-4600
Facsimile: 760-930-0698
EUROPE
Astec House, Waterfront Business Park
Merry Hill, Dudley
West Midlands, DY5 1LX, UK
Telephone: 44 (1384) 842-211
Facsimile: 44 (1384) 843-355
ASIA
Units 2111-2116, Level 21
Tower1, Metroplaza
223, Hing Fong Road
Fwai Fong, New Territories
Hong Kong
Telephone: 852-2437-9662
Facsimile: 852-2402-4426
Ordering Information
Input
Voltage
48V
48V
48V
48V
48V
Output
Voltage
3.3V @ 60A
2.5V @ 60A
2.5V @ 60A
1.8V @ 60A
1.2V @ 60A
Efficiency
91% (Typ)
90% (Typ)
90% (Typ)
89% (Typ)
85% (Typ)
Model Number
AEH60F48(N)
AEH60G48(N)
AEH60G48N-6T
AEH60Y48(N)
AEH60K48(N)
(see note 3)
48V
48V
48V
48V
OPTION:
3.3V @ 60A
2.5V @ 60A
1.8V @ 60A
1.2V @ 60A
91% (Typ)
90% (Typ)
89% (Typ)
85% (Typ)
ALH60F48(N)
ALH60G48(N)
ALH60Y48(N)
ALH60K48(N)
suffix “N” = Negative Enable (default is Positive Enable without suffix “N”)
Standard pin length is 5mm nominal. Consult factory for other options.
Pin Assignments
Single Output
1. +Vin
2. Enable (On/Off)
3. Case (AEH version)
4. -Vin
5. - Output
6. - Sense
7. Trim
8. + Sense
9. + Output
Notes:
1. 20 mHz bandwidth. External 10 uF tant. capacitor +
0.1 uF cer. capacitor placed from +V out to -Vout.
2. Requires a 2.2 mf, 100V film capacitor connected
between +V in and -V in to meet FCC class A and
ETS300-386-1 requirements for conducted noise.
Consult Factory for filtering information to meet FCC
class B, VDE or EIC specifications.
3. Suffix -”6” for 3.7mm nominal pin length, “T” for tuned
version for specific transient response requirement.
Minimum output capacitance required. Refer to
Technical refernce Notes for details.
4. All specifications are typical at nominal line, full load,
and 25°C unless otherwise noted.
5. All specifications subject to change without notice.
Mechanical drawings are for reference only
6. Technical Reference Notes should be consulted for
detailed information when available
7. Warranty: 1yr
* Astec reserves the right to make changes to the information
contained herein without notice and assumes no liability as a
result of its use or application. (REV05: FEBRUARY 2, 2004)
AEH - BASEPLATE
0.20
[5.1]
2.30
[58.4]
1.90
[48.3]
M3 X0.5 MOUNTING HOLE
4 PLACES
0.20
[5.1] + Vin
+ Output
2.00 2.40
[50.8] [61.0]
0.50
[12.7]
0.20
[5.2]
0.08Ø[2.0Ø] 2 PLACES
0.04Ø [1.0Ø] 7 PLACES
- Vin
-Output
PIN SIDE DOWN
0.50
[12.7]
1.90
[48.3]
0.90
1.20 [22.8]
1.50 [30.4]
1.90 [38.1]
[48.3]
4
3
2
1
5
6
7
9
0.50
[12.7]
0.46
[11.8]
SIDE VIEW
0.90
[22.9]
1.20
[30.5] 1.50
[38.2]
1.90
[48.3]
PIN ASSIGNMENT
1 + Vin
2 Enable (On/Off)
3 CASE
4 - Vin
5 -Output
6 -Sense
7 Trim
8 + Sense
9 + Output
PIN SIDE UP
0.20
[5.1]
2.30
[58.4]
1.90
[48.3]
0.40
[10.2]
NOTES:
ALL DIMENSIONS ARE IN INCHES (MILLIMETERS)
PIN PLACEMENT TOLERANCE : ± 0.005(0.127)
MECHANICAL TOLERANCE ± .002(0.5)
0.21
[5.4]
0.20
[5.1] + Vin 1
2.40 2.00
[60.9] [50.8]
2
3
- Vin 4
9 + Output
8
7
6
5 -Output
0.04Ø[1.0Ø] 7 PLACES
0.08Ø[2.0Ø] 2 PLACES
0.50
[12.7]
0.90
1.20 [22.9]
[30.5]
1.50
1.90 [38.1]
[48.3]
PIN SIDE DOWN
1.90
[48.3]
45
36
7
28
19
PIN SIDE UP
SIDE VIEW
0.50
[12.7] 0.90
[22.9]
1.20
[30.5] 1.50
[38.1] 1.90
[48.2]
PIN ASSIGNMENT
1 + Vin
2 Enable (On/Off)
3 CASE
4 - Vin
5 -Output
6 -Sense
7 Trim
8 + Sense
9 + Output
NOTES:
ALL DIMENSIONS ARE IN INCHES (MILLIMETERS)
PIN PLACEMENT TOLERANCE : ± 0.005(0.127)
MECHANICAL TOLERANCE ± .002(0.5)
ALH - BASEPLATE
www.astecpower.com
3