HPS3000-9.pdf 데이터시트 (총 7 페이지) - 파일 다운로드 HPS3000-9 데이타시트 다운로드

No Preview Available !

Embedded Power for
Business-Critical Continuity
HPS3000 Series
3000 Watts
Distributed Power Bulk Front-End
Single Output
Rev. 7.10.09_81
HPS3000 Series
 of 7
Special Features
• 3000 W output power
• 40 W/cu-in
• Optional customer provided air
• 1U x 3U form factor
• N+1 Redundant
• Hot-swap
• Internal OR-ing
• 5 V housekeeping
• High efficiency 89% @ 200 Vac,
100% load
• Variable speed “smart fans”
• One year warranty
Compliance
• POE Isolation
• EMI Class B - EN55022, Level “A”
• EN61000 Immunity
Electrical Specifications
Input
Input ra­nge (operating):
Input range (nominal):
Frequency:
180 - 264 Vac
90 - 140 Vac
200 Vac
110 Vac
43 to 63 Hz
Input through Card Edge Connection
on same end as DC output
Input fusing:
Internal 25 A fuses
Both lines fused
Inrush current:
≤40 A peak
Either hot or cold start
Power factor:
0.97 typical
Meets EN61000-3-2
Harmonics:
Meets IEC 1000-3-2
requirements
@ 50% load
Input current:
19 A max input current
Holdup time:
10 ms minimum
At full rated load
Leakage current:
1.4 mA
At 240 Vac
Power line transient:
MOV directly after the fuse
Safety
UL/cUL
CSA
China
Nemko
CB Report
CSA 22.2
60950
60950
CCC
TUV
60950

No Preview Available !

Embedded Power for
Business-Critical Continuity
230V ac E ffic ienc y
230 Vac Efficiency
100.00
90.00
80.00
70.00
60.00
50.00
40.00
30.00
20.00
10.00
10 20 30 40 50 60 70 80 90 100
% of Total Output Pow er
Rev. 7.10.09_81
HPS3000 Series
 of 7
Output
Output rating
Set point
Total regulation range
Rated load
Minimum load
Output noise
48 V @ 62.0 A
5 Vsb @ 3.0 A
48 V @ 29.4 A
5V @ 3 A
48 V
48 V ± 10%
5 Vsb ± 4%
3000 W maximum @ 200 Vac Input
1500 W maximum @ 110 Vac Input
48 V @ 0.0 A
5 Vsb @ 0.0 A
480 mV max P-P
100 mV max P-P
Output voltage overshoot
Transient response
± 5% maximum
5% maximum deviation
Max units in parallel
Up to 4
Short circuit protection
120% - 130% of rated output
Output isolation
Per POE specs
Forced load sharing
Within 10% of all shared outputs
Over current protection (OCP) 120% to 130%
100% to 125%
Over voltage protection (OVP) 110% to 120%
110% to 125%
Over temperature protection 10 - 15 deg C above safe
operating area
180 - 264 Vac
90 - 140 Vac
Programmable ±10% through I2C serial bus
Line/load/transient when measured at output connection
No derating over operating temp range
No loss of regulation
48 V output
5 Vsb output
Measured with a 0.1µF Ceramic and 10 µF Tantalum capacitor on any
input
Nominal Voltage Setting
50% load step @ 1 A/us
Step load valid between 10% to 100% of output rating.
Total power in 1U 19” rack is 12 KW
Output to return
>2000 Vac
Digital sharing control
48 V output
5 Vsb output
48 V output
5 Vsb output
Both PFC and output converter monitored
5 Vsb will operate under overtemperature condition.
Built in hysteresis
Environmental Specifications
Vibration/Shock:
Operating temperature:­­
Storage Temperature:
Cooling
Operating Relative Humidity:
Storage Relative Humidity:
Operating Altitude
Storage Altitude:
RoHS Compliant:
Non-operational 5G Sine sweep from 5 Hz to 500 Hz, dwelling at resonant frequencies for 1 hour each
-10 ° to +40 °C
-40 ° to +85 °C
External fans with Fan Fail and Fan Speed control
5% to 95% non-condensing
5% to 95% non-condensing
Up to 10,000 feet above sea level
Up to 30,000 feet above sea level
Yes

No Preview Available !

Module Information
(All units in mm)
321.4 ± 1.2
327.6 ± 1.2
AIRFLOW DIRECTION
Pin Assignments
Bottom
Pin
1 AC LINE
2 AC LINE
3 n.c.
4 AC NEUTRAL
5 AC NEUTRAL
6 n.c.
7 n.c.
8 n.c.
9 +48 Vdc out
10 +48 Vdc out
11 +48 Vdc out
12 +48 Vdc out
13 +48 Vdc out
14 +48 Vdc out
15 +48 Vdc out
16 +48 Vdc RTN
17 +48 Vdc RTN
18 +48 Vdc RTN
19 +48 Vdc RTN
20 +48 Vdc RTN
21 +48 Vdc RTN
22 +48 Vdc RTN
23 n.c.
24 V_STBY
25 STBY_RTN_SENSE
26 PRESENT#
27 DCOK/PWOK#
28 SDA
29 HVCC
30 PSON#
31 #ALERT
32 ISHARE
Top
Pin
64 AC LINE
63 AC LINE
62 n.c.
61 AC NEUTRAL
60 AC NEUTRAL
59 n.c.
58 n.c.
57 n.c.
56 +48 Vdc out
55 +48 Vdc out
54 +48 Vdc out
53 +48 Vdc out
52 +48 Vdc out
51 +48 Vdc out
50 +48 Vdc out
49 +48 Vdc RTN
48 +48 Vdc RTN
47 +48 Vdc RTN
46 +48 Vdc RTN
45 +48 Vdc RTN
44 +48 Vdc RTN
43 +48 Vdc RTN
42 n.c.
41 SYS_GND
40 STBY_SENSE
39 ACOK#
38 SMBUS_ALERT_OUT
37 SCL
36 A2
35 PSKILL
34 A1
33 A0
11.9 ± 1
Tyco Connector
PN: 2007209
or
FCI
10053363-400LF
Embedded Power for
Business-Critical Continuity
Rev. 7.10.09_81
HPS3000 Series
 of 7
11.6 ± 0.5

No Preview Available !

AC Input
Main Vout
PWOK
5 vsb Vout
PS_ON
AC_OK
Embedded Power for
Business-Critical Continuity
Timing Diagram
AC On
T Vout_Holdup
AC On
T PWOK_Off_
Rev. 7.10.09_81
HPS3000 Series
4 of 7
T AC_On_Delay
T PWOK_Off_
T PWOK_Off_
T PWOK_On
T PWOK_Off_
T PWOK_Delay
T PWOK_On
T sb_On
T PWOK_On
T PWOK_Off
T PSON_PWOK
T SB_Vout
T PSON_On_Delay
T ACOK_Delay
AC Input
ON / OFF Cycle
PSON
ON / OFF
Cycle

No Preview Available !

Embedded Power for
Business-Critical Continuity
Timing Signal Definitions
Turn ON/OFF Timing
Item
Description
Tvout_rise
Tsb_on_delay
48 V Output rise time
Delay from AC being applied to 5 Vsb being within regulation.
Tac_on_delay
Delay from AC being applied to all output voltages being within
regulation.
Tvout_holdup
Tpwok_holdup
Time all output voltages, including 5 Vsb, stay within regulation
after loss of AC.
Delay from loss of AC to de-assertion of PWOK
Tpson_on_delay
Tpson_pwok
Tacok_delay
Delay from PSON# active to output voltages within regulation
limits.
Delay from PSON# de-active to PWOK being de-asserted.
Delay from loss of AC input to de-assertion of ACOK#.
Tpwok_on
Tpwok_off
Tpwok_low
Delay from output voltages within regulation limits to PWOK
asserted at turn on.
Delay from PWOK de-asserted to 48 V dropping out of regulation
limits.
Duration of PWOK being in the de-asserted state during an off/on
cycle using AC or the PSON# signal.
Tsb_vout
Delay from 5 Vsb being in regulation to 48 V being in
regulation at AC turn on.
Min
5
10
5
5
10
100
1
100
50
Max
300
1500
2000
Units
msec
msec
msec
msec
msec
400 msec
50
1000
msec
msec
msec
1000 msec
msec
2000 msec
Signals and Controls - All Models
Rev. 7.10.09_81
HPS3000 Series
5 of 7
PSON #
The PSON# signal is required to remotely turn on/off the power supply. PSON# is an active low signal
that turns on the 48 V power rail. When this signal is not pulled low by the system, or left open, the
48 V output turns off. The 5 Vsb output remains on. This signal is pulled to a standby voltage by a
pull-up resistor internal to the power supply. The power supply fan(s) shall operate at the lowest speed.
PSON# Signal Characteristic
Signal Type
Accepts an open collector/drain input from
the system. Pulled-up to the 5 Vsb located in
power supply.
PSON# = Low
ON
PSON# = Open
OFF
MIN MAX
Logic level low (power supply ON)
0V
0.8 V
Logic level high (power supply OFF)
2.0 V
4.80 V
Source current, Vpson = low
--
4 mA
Power up delay: Tpson_on_delay
5 msec
400 msec