G084SN05-V2.pdf 데이터시트 (총 26 페이지) - 파일 다운로드 G084SN05-V2 데이타시트 다운로드

No Preview Available !

Spec. No.:
www.DataSheet4U.com
MDGD084-SN05-2
Version:
0.2
Total pages:
26
Date:
2004- March-15
AU OPTRONICS CORPORATION
Product Functional Specifications
8.4SVGA Color TFT-LCD Module
Model Name: G084SN05 V.2
Approved by
Martin Sun
Prepared by
Cynthia Lin
GD- MDBU Marketing Division / AU Optronics Croporation
Customer
Checked & Approved by
(C) Copyright AU Optroncis, Inc.
2004 All Right Reserved.
No Reproduction and Redistribution Allowed.
G084SN05 V.2 ver.0.2
1/1

No Preview Available !

www.DataSheet4U.com
Version: 0.2
Total Pages: 26
Date: 2004/03/15
Product Functional Specification
8.4 inch SVGA Color TFT LCD Module
Model Name: G084SN05 V.2
(u) Preliminary Specification
( ) Final Specification
Official UK Representative
Unit A Merlin Centre, Gatehouse Close,
Aylesbury, HP19 8DP, ENGLAND
Tel.: +44 (0)1296-469770 Fax.: +44 (0)1296-469779
sales@displaze.com
www.displaze.com
Please verify this is the latest information. E&OE
Note: This Specification is subject to change without notice.
(C) Copyright AU Optroncis, Inc.
2004 All Right Reserved.
No Reproduction and Redistribution Allowed.
G084SN05 V.2 ver.0.2
2/2

No Preview Available !

I. Contents
1.0 Handling Precautions
2.0 General Description
2.1 Characteristics
2.2 Functional Block Diagram
3.0 Absolute Maximum Ratings
4.0 Optical Characteristics
5.0 Signal Interface
5.1 Connectors
5.2 Signal Pin
5.3 Signal Description
5.4 Signal Electrical Characteristics
5.5 Signal for Lamp Connector
6.0 Pixel Format Image
6.1 Scanning Direction
7.0 Parameter Guideline for CCFL Inverter
8.0 Interface Timings
8.1 Timing Characteristics
8.2 Timing Definition
9.0 Power Consumption
10.0 Power On/Off Sequence
11.0 Mechanical Characteristics
www.DataSheet4U.com
(C) Copyright AU Optroncis, Inc.
2004 All Right Reserved.
No Reproduction and Redistribution Allowed.
G084SN05 V.2 ver.0.2
3/3

No Preview Available !

www.DataSheet4U.com
II. Record of Revision
Version and Date Page
Old Description
New Description
Remark
0 2003/11/27
All First Draft
First Draft
0.1 2004/2/10
6
Add functional block diagram
16 Update CCFL spec.
24 Update outline drawing
0.2 2004/3/15
6 Power Consumption: 5.3W
Weight: 275±10
Power Consumption: 7.5W
Weight: 310±10
Physical size: 203x142.5x11.4 Physical size: 203x142.5x12.5
11 Connector 2 Type/Part Number
Correction
14 Lamp connector
Lamp connector
Pin 1: L, Pin 3: H
Pin 1: H, Pin 3: L
23 VDD, PDD & IDD updated
25,26
Drawing updated
(C) Copyright AU Optroncis, Inc.
2004 All Right Reserved.
No Reproduction and Redistribution Allowed.
G084SN05 V.2 ver.0.2
4/4

No Preview Available !

www.DataSheet4U.com
1.0 Handing Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnection from input
connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or
spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard
surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure
human earth when handling.
7) Do not open nor modify the module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a module has to be put back into the packing container slot after once it was
taken out from the container, do not press the center of the CCFL Reflector edge.
Instead, press at the far ends of the CCFL Reflector edge softly. Otherwise the TFT
module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor
tilt the interface Connector of the TFT module.
11) After installation of the TFT module into an enclosure, do not twist nor bend the TFT
module even momentary. At designing the enclosure, it should be taken into
consideration that no bending/twisting forces are applied to the TFT module from
outside. Otherwise the TFT module may be damaged.
12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please
follow local ordinances or regulations for disposal.
13) Small amount of materials having no flammability grade is used in the LCD module
should be supplied by power complied with requirements of Limited Power Source, or
be applied exemption.
14) The LCD module is designed so that the CCFL in it is supplied by Limited Current
Circuit. Do not connect the CCFL in Hazardous Voltage Circuit.
(C) Copyright AU Optroncis, Inc.
2004 All Right Reserved.
No Reproduction and Redistribution Allowed.
G084SN05 V.2 ver.0.2
5/5