6163R50KT5L1.0XX.pdf 데이터시트 (총 4 페이지) - 파일 다운로드 6163R50KT5L1.0XX 데이타시트 다운로드

No Preview Available !

MODEL 6143, 6163
7/8” Diameter
Single Turn
Conductive Plastic
Precision Potentiometer /
Position Sensor
MODEL STYLES
6143
6163
ELECTRICAL
Resistance Range, Ohms
Standard Resistance Tolerance
Minimum Practical Resistance Tolerance
Independent Linearity*
Minimum Practical Independent Linearity
Input Voltage, Maximum
Power Rating, Watts
Dielectric Strength
Insulation Resistance, Minimum
Output Smoothness, Maximum
Actual Electrical Travel, Nominal
Electrical Continuity Travel, Minimum
End Voltage, Maximum
Resolution
Temperature Coefficient**
Specifications subject to change without notice.
* Linearity is measured between 1% and 99% of input voltage.
** Special tempco available to ±100ppm/°C.
2
1/8” Shaft, Bronze Sleeve Bearing
1/8” Shaft, Ball Bearing
1K to 100K
±10%
±5%
±1.0%
±0.5%
400Vdc not to exceed power rating
1.0 at 70°C derating to 0 at 125°C
750V rms
1,000 Megohms
0.1%
340°
350°
0.5% of Input Voltage
Essentially infinite
–800 ppm/°C
www.DataSheet.in
2-59
Model 6143, 6163

No Preview Available !

ENVIRONMENTAL (MIL-R-39023)
Operating Temperature Range
Temperature Cycling
Shock, 6ms Sawtooth
Vibration
Moisture Resistance
High Temperature Exposure
Rotational Life
Rotational Load Life
Static: –65°C to +125°C
Dynamic: –40°C to +125°C
5 cycles, –65°C to +125°C (10% R)
100G’s (0.1ms discontinuity max.)
10G’s, 10 to 500 Hz (2% R, 0.1ms discontinuity max.)
Five 24 hour cycles (10% R)
1,000 hours at 125°C (0.5% R)
6143:
6163:
10 mil. shaft rev.
25 mil. shaft rev.
5 mil. shaft rev. at rated wattage at 70°C (10% R)
MECHANICAL
Total Mechanical Travel
Number of Gangs, Maximum
Weight, Nominal
Shaft Runout, T.I.R., Maximum
Pilot Diameter Runout, T.I.R., Maximum
Lateral Runout, T.I.R., Maximum
Shaft Radial Play, Maximum
Start/Run Torque, Maximum
Bearing Type
6143
.003”
.005”
.005”
.005”
0.6 oz.-in.
Bronze Sleeve Bearing
360° continuous
1
0.46 oz.
6163
.003”
.003”
.003”
.005”
0.5 oz.-in.
Ball Bearing
STANDARD RESISTANCE VALUES, OHMS
1K 2K
5K 10K
20K 50K
METRIC CONVERSIONS
1 in.
1 oz.
25.4 mm
28.4 gm
1 oz.-in.
1 lb.-in.
0,007 N-m
0,113 N-m
www.DataSheet.in
2-60
Model 6143, 6163

No Preview Available !

OUTLINE DIMENSIONS (Inch/mm)
45°±5°
Typ.
CW
.595±.015
15.1±0.38
.500
12.7
Max.
Mounting Surface
.500±.031
12.7±0.79
Adjustment Slot (Optional)
.032±.005
0.81±0.13
Wide
x
0.0.8312±±0.0.1035 Deep
CCW
.840±.005
21.3±0.13
Dia.
Slider
.187±.015 R.
4.75±0.38
.750±.005 Dia.
19.1±0.13
.062±.005
1.58±0.13
.062±.005
1.58±0.13
.062±.005
1.58±0.13
+.0000
.7500 -.0005 Dia.
+0.0000
19.050 -0.0127
.875±.005 Dia.
22.2±0.13
Chamfer.010±.005
0.25±0.13
Max.
x
45°
+.0000
.1248 -.0003 Dia.
+0.000
3.170 -0.008
2
www.DataSheet.in
2-61
Model 6143, 6163

No Preview Available !

SPECIAL FEATURES
Linearity Tape
Flatted Shaft
Slotted Shaft
ORDERING INFORMATION
6163 R 10K T5 L 1.0 XX
Model Series
6143 - Bronze Sleeve Bearing
6163 - Ball Bearing
Resistance Prefix
Resistance Value
Optional Special
Feature Code
Linearity
Optional
Non-Standard Tolerance
LT
FS
SS
2
CIRCUIT DIAGRAM
(CCW)
(S)
(CW)
NOTES
Metric equivalents, based on 1 inch = 25.4mm are rounded to
the same number of significant figures as in the original
English units and are provided for general information only.
Tolerances unless otherwise specified:
Linear = ± .01 inches
(.25mm)
Angular = ± 2 degrees
INCH
mm
www.DataSheet.in
2-62
Model 6143, 6163