G121SN01-V1.pdf 데이터시트 (총 28 페이지) - 파일 다운로드 G121SN01-V1 데이타시트 다운로드

No Preview Available !

Spec. No.: MDGD012-SN01-1
Version:
1
Total pages:
28
Date:
2005 May - 11
AU OPTRONICS CORPORATION
Product Functional Specifications
12.1SVGA Color TFT-LCD Module
Model Name: G121SN01 V.1
www.DataSheet.co.kr
Approved by
Prepared by
GD- MDBU Marketing Division / AU Optronics Croporation
Customer
Checked & Approved by
(C) Copyright AU Optroncis, Inc.
2004 All Right Reserved.
No Reproduction and Redistribution Allowed.
G121SN01 V.1 ver.1
1/28
Datasheet pdf - http://www.DataSheet4U.net/

No Preview Available !

Version: 1
Total Pages: 28
Date: 2005/05/11
Product Functional Specification
12.1 inch SVGA Color TFT LCD Module
Model Name: G121SN01 V.1
www.DataSheet.co.kr
(u) Preliminary Specification
( ) Final Specification
Note: This Specification is subject to change without notice.
(C) Copyright AU Optroncis, Inc.
2004 All Right Reserved.
No Reproduction and Redistribution Allowed.
G121SN01 V.1 ver.1
2/28
Datasheet

No Preview Available !

I. Contents
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
11.0
12.0
13.0
Handling Precautions…………………………………………………..5
General Description……………………………………………………….6
2.1 Display Characteristics
2.2 Functional Block Diagram
Absolute Maximum Ratings……………………………………………...8
Optical Characteristics……………………………………………………9
Signal Interface……………………………………………………………12
5.1 Connectors
5.2 Signal Pin
5.3 Signal Description
5.4 Signal Electrical Characteristics
5.5 Signal for Lamp Connector
Pixel Format Image………………………………………………………16
6.1 Scanning Direction...……………………………………………17
Parameter Guide Line CCFL Inverter…….…………………………...17
Interface Timing..…………………………………………………………18
8.1 Timing Characteristics
8.2 Timing Definition
www.DataSheet.co.kr
8.3 Timing Chart
Power Consumption……………………………………………………..22
Power ON/OFF Sequence……………………………………………….23
Reliability / Safety Requirement……………………………………..24
11.1 Reliability Test Conditions
11.2 Safety
11.3 Green
Packing Dimension………………………….……………………………25
Mechanical Characteristics……………………………………………..26
13.1 LCM Outline dimension (Front View)
13.2 LCM Outline Dimension (Rear View)
13.3 Screw Note
(C) Copyright AU Optroncis, Inc.
2004 All Right Reserved.
No Reproduction and Redistribution Allowed.
G121SN01 V.1 ver.1
3/28
Datasheet pdf - http://www.DataSheet4U.net/

No Preview Available !

II. Record of Revision
Version and Date Page
Old Description
New Description
Remark
0. 2004/11/01
All First Draft
All
1. 2005/05/11
6 Brightness: 180/140
200/160
6 Contrast ratio: 350:1
500:1
8 Vs: 690/890
Vs: 970/1270
9 Contrast ration, Viewing Angle, Updated
CIE, Brightness
12 Signal Connector
Add mating connector type
15 Clock frequency: 20/85
Clock frequency: 30/50
17 Add 6.1: Scanning Direction
17 Modify ICFL, FCFL, Vs, VCFL,
PCFL, Lamp life
22 Add PCFL
24 Modify high temperature &
high humidity operation
www.DataSheet.co.kr
condition
24 Modify Thermal shock
condition
25 Add packing dimension
28 Add screw note
(C) Copyright AU Optroncis, Inc.
2004 All Right Reserved.
No Reproduction and Redistribution Allowed.
G121SN01 V.1 ver.1
4/28
Datasheet pdf - http://www.DataSheet4U.net/

No Preview Available !

1.0 Handing Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnection from input
connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration
or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on
hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure
human earth when handling.
7) Do not open nor modify the module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a module has to be put back into the packing container slot after once it
was taken out from the container, do not press the center of the CCFL Reflector
edge. Instead, press at the far ends of the CFL Reflector edge softly. Otherwise
the TFT module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate
www.DataSheet.co.kr
nor tilt the interface Connector of the TFT module.
11) After installation of the TFT module into an enclosure, do not twist nor bend the
TFT module even momentary. At designing the enclosure, it should be taken into
consideration that no bending/twisting forces are applied to the TFT module from
outside. Otherwise the TFT module may be damaged.
12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please
follow local ordinances or regulations for disposal.
13) Small amount of materials having no flammability grade is used in the LCD
module should be supplied by power complied with requirements of Limited Power
Source, or be applied exemption.
14) The LCD module is designed so that the CCFL in it is supplied by Limited Current
Circuit. Do not connect the CFL in Hazardous Voltage Circuit.
(C) Copyright AU Optroncis, Inc.
2004 All Right Reserved.
No Reproduction and Redistribution Allowed.
G121SN01 V.1 ver.1
5/28
Datasheet pdf - http://www.DataSheet4U.net/