LC-52LE810UN.pdf 데이터시트 (총 30 페이지) - 파일 다운로드 LC-52LE810UN 데이타시트 다운로드

No Preview Available !

LC-40/46/52/60LE810UN (1st Edition)
SERVICE MANUAL
No. S30E840LE810U
LCD COLOR TELEVISION
LC-40LE810UN
LC-46LE810UN
LC-52LE810UN
MODELS LC-60LE810UN
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its orig-
inal condition and only parts identical to those specified should be used.
CONTENTS
SAFETY PRECAUTION
IMPORTANT SERVICE SAFETY
PRECAUTION....................................................i
PRECAUTIONS A PRENDRE LORS DE
LA REPARATION ..............................................ii
PRECAUTIONS FOR USING LEAD-FREE
SOLDER .......................................................... iii
OUTLINE
MAJOR SERVICE PARTS ...............................iv
[2] REMOVING OF MAJOR PARTS
(LC-46LE810UN) ........................................... 4-6
[3] REMOVING OF MAJOR PARTS
(LC-52LE810UN)......................................... 4-11
[4] REMOVING OF MAJOR PARTS
(LC-60LE810UN) ......................................... 4-16
CHAPTER 5. ADJUSTMENT
[1] ADJUSTMENT PROCEDURE ......................5-1
[2] PUBLIC MODE SETTING PROCEDURE......5-15
CHAPTER 1. SPECIFICATIONS
[1] SPECIFICATIONS (LC-40/46LE810UN)........ 1-1
[2] SPECIFICATIONS (LC-52/60LE810UN)........ 1-2
CHAPTER 2. OPERATION MANUAL
[1] Parts Name ................................................... 2-1
[2] OPERATION MANUAL ................................. 2-3
CHAPTER 6. TROUBLESHOOTING TABLE
[1] TROUBLESHOOTING TABLE ......................6-1
[2] LED flashing specification at the time of an
error (Center icon LED used) ......................6-14
CHAPTER 7. MAJOR IC INFORMATIONS
[1] MAJOR IC INFORMATIONS .........................7-1
CHAPTER 3. DIMENSIONS
[1] DIMENSIONS (LC-40LE810UN)................... 3-1
[2] DIMENSIONS (LC-46LE810UN)................... 3-2
[3] DIMENSIONS (LC-52LE810UN)................... 3-3
[4] DIMENSIONS (LC-60LE810UN)................... 3-4
CHAPTER 4. REMOVING OF MAJOR PARTS
[1] REMOVING OF MAJOR PARTS
(LC-40LE810UN) .......................................... 4-1
CHAPTER 8. OVERALL WIRING/SYSTEM BLOCK
DIAGRAM
[1] OVERALL WIRING DIAGRAM ......................8-1
[2] SYSTEM BLOCK DIAGRAM .........................8-2
Parts Guide
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the
safety and performance of the set.
This document has been published to be used for
after sales service only.
The contents are subject to change without notice.
Free Datasheet http://www.datasheet4u.com/

No Preview Available !

LC-40/46/52/60LE810UN (1st Edition)
LSCA-40FLEE8T10YUNPRECAUTION
Service Manual
IMPORTANT SERVICE SAFETY PRECAUTION
Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the
servicing guidelines which follow:
„WARNING
1. For continued safety, no modification of any circuit should be
attempted.
2. Disconnect AC power before servicing.
C A U T I O N : F O R C O N T I N U E D PROTECTION
AGAINST A RISK OF FIRE REPLACE ONLY WITH
SAME TYPE FUSE.
F7000 (250V 3.5A) (LC-40LE810UN)
F7001 (250V 3.5A) (LC-40LE810UN)
F7000 (250V 5A) (LC-46/52/60LE810UN)
F7001 (250V 5A) (LC-46/52/60LE810UN)
• Using two clip leads, connect a 1.5k ohm, 10 watt resistor paral-
leled by a 0.15µF capacitor in series with all exposed metal cabinet
parts and a known earth ground, such as electrical conduit or elec-
trical ground connected to an earth ground.
• Use an AC voltmeter having with 5000 ohm per volt, or higher, sen-
sitivity or measure the AC voltage drop across the resistor.
• Connect the resistor connection to all exposed metal parts having a
return to the chassis (antenna, metal cabinet, screw heads, knobs
and control shafts, escutcheon, etc.) and measure the AC voltage
drop across the resistor.
All checks must be repeated with the AC cord plug connection
reversed. (If necessary, a nonpolarized adaptor plug must be used
only for the purpose of completing these checks.)
Any reading of 0.75 Vrms (this corresponds to 0.5 mA rms AC.) or
more is excessive and indicates a potential shock hazard which
must be corrected before returning the monitor to the owner.
„BEFORE RETURNING THE RECEIVER (Fire &
Shock Hazard)
Before returning the receiver to the user, perform the following
safety checks:
3. Inspect all lead dress to make certain that leads are not pinched,
and check that hardware is not lodged between the chassis and
other metal parts in the receiver.
4. Inspect all protective devices such as non-metallic control knobs,
insulation materials, cabinet backs, adjustment and compartment
covers or shields, isolation resistor-capacitor networks, mechanical
insulators, etc.
5. To be sure that no shock hazard exists, check for leakage current in
the following manner.
• Plug the AC cord directly into a 120 volt AC outlet.
DVM
AC SCALE
1.5k ohm
10W
0.15 µF
TEST PROBE
TO EXPOSED
METAL PARTS
CONNECT TO
KNOWN EARTH
GROUND
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
SAFETY NOTICE
Many electrical and mechanical parts in LCD color television have
special safety-related characteristics.
For continued protection, replacement parts must be identical to those
used in the original circuit.
These characteristics are often not evident from visual inspection, nor
can protection afforded by them be necessarily increased by using
replacement components rated for higher voltage, wattage, etc.
The use of a substitute replacement parts which do not have the same
safety characteristics as the factory recommended replacement parts
shown in this service manual, may create shock, fire or other hazards.
Replacement parts which have these special safety characteristics are
identified in this manual; electrical components having such features
are identified by " " and shaded areas in the Replacement Parts List
and Schematic Diagrams.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
i
Free Datasheet http://www.datasheet4u.com/

No Preview Available !

PRECAUTIONS A PRENDRE LORS DE LA REPARATION
LC-40/46/52/60LE810UN (1st Edition)
Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement accoutumé à toute vérification de sécurité et aux
conseils suivants.
AVERTISSEMENT
1. N'entreprendre aucune modification de tout circuit. C'est danger-
eux.
2. Débrancher le récepteur avant toute réparation.
PRECAUTION: POUR LA PROTECTION CON-
TINUE CONTRE LES RISQUES D'INCENDIE,
REMPLACER LE FUSIBLE
F7000 (250V 3.5A) (LC-40LE810UN)
F7001 (250V 3.5A) (LC-40LE810UN)
F7000 (250V 5A) (LC-46/52/60LE810N)
F7001 (250V 5A) (LC-46/52/60LE810UN)
• A l'aide de deux fils à pinces, brancher une résistance de 1.5 k
10 watts en parallèle avec un condensateur de 0.15µF en série
avec toutes les pièces métalliques exposées du coffret et une terre
connue comme une conduite électrique ou une prise de terre
branchée à la terre.
• Utiliser un voltmètre CA d'une sensibilité d'au moins 5000/V pour
mesurer la chute de tension en travers de la résistance.
• Toucher avec la sonde d'essai les pièces métalliques exposées qui
présentent une voie de retour au châssis (antenne, coffret métalli-
que, tête des vis, arbres de commande et des boutons, écusson,
etc.) et mesurer la chute de tension CA en-travers de la résistance.
Toutes les vérifications doivent être refaites après avoir inversé la
fiche du cordon d'alimentation. (Si nécessaire, une prise
d'adpatation non polarisée peut être utilisée dans le but de termin-
er ces vérifications.)
La tension de pointe mesurèe ne doit pas dépasser 0.75V (corre-
spondante au courant CA de pointe de 0.5mA).
Dans le cas contraire, il y a une possibilité de choc électrique qui
doit être supprimée avant de rendre le récepteur au client.
VERIFICATIONS CONTRE L'INCEN-DIE ET LE
CHOC ELECTRIQUE
Avant de rendre le récepteur à l'utilisateur, effectuer les vérifica-
tions suivantes.
3. Inspecter tous les faisceaux de câbles pour s'assurer que les fils
ne soient pas pincés ou qu'un outil ne soit pas placé entre le châs-
sis et les autres pièces métalliques du récepteur.
4. Inspecter tous les dispositifs de protection comme les boutons de
commande non-métalliques, les isolants, le dos du coffret, les cou-
vercles ou blindages de réglage et de compartiment, les réseaux
de résistancecapacité, les isolateurs mécaniques, etc.
5. S'assurer qu'il n'y ait pas de danger d'électrocution en vérifiant la
fuite de courant, de la facon suivante:
• Brancher le cordon d'alimentation directem-ent à une prise de cou-
rant de 120V. (Ne pas utiliser de transformateur d'isolation pour
cet essai).
DVM
ECHELLE CA
1.5k ohm
10W
0.15 µF
SONDE D'ESSAI
AUX PIECES
METALLIQUES
EXPOSEES
BRANCHER A UNE
TERRE CONNUE
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
AVIS POUR LA SECURITE
De nombreuses pièces, électriques et mécaniques, dans les télévi-
seur ACL présentent des caractéristiques spéciales relatives à la sé-
curité, qui ne sont souvent pas évidentes à vue. Le degré de protec-
tion ne peut pas être nécessairement augmentée en utilisant des
pièces de remplacement étalonnées pour haute tension, puissance,
etc.
Les pièces de remplacement qui présentent ces caractéristiques sont
identifiées dans ce manuel; les pièces électriques qui présentent ces
particularités sont identifiées par la marque " " et hachurées dans la
liste des pièces de remplacement et les diagrammes schématiques.
Pour assurer la protection, ces pièces doivent être identiques à celles
utilisées dans le circuit d'origine. L'utilisation de pièces qui n'ont pas
les mêmes caractéristiques que les pièces recommandées par l'usine,
indiquées dans ce manuel, peut provoquer des électrocutions, incen-
dies, radiations X ou autres accidents.
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
ii
Free Datasheet http://www.datasheet4u.com/

No Preview Available !

LC-40/46/52/60LE810UN (1st Edition)
PRECAUTIONS FOR USING LEAD-FREE SOLDER
„Employing lead-free solder
• “PWBs” of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The
alphabetical character following LF shows the type of lead-free solder.
Example:
Indicates lead-free solder of tin, silver and copper.
Indicates lead-free solder of tin, silver and copper.
„Using lead-free wire solder
• When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead wire solder may cause dam-
age or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40 °C, we recommend you to use a dedicated soldering
bit, if you are not familiar with how to obtain lead-free wire solder or soldering bit, contact our service station or service branch in your area.
„Soldering
• As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 °C which is higher than the conventional lead solder by 40 °C, and as it has poor
solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may be
peeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the
steady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit as
required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
• Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
PARTS CODE
ZHNDAi123250E
ZHNDAi126500E
ZHNDAi12801KE
PRICE
RANK
BL
BK
BM
PART
DELIVERY
J
J
J
DESCRIPTION
φ0.3mm 250g (1roll)
φ0.6mm 500g (1roll)
φ1.0mm 1kg (1roll)
iii
Free Datasheet http://www.datasheet4u.com/

No Preview Available !

LOCU-40TLEL8I1N0UEN
LC-40/46/52/60LE810UN (1st Edition)
Service Manual
MAJOR SERVICE PARTS
„PWB UNIT
Ref No.
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Part No.
DKEYMF452FM01
DUNTKF493FM01
DUNTKF494FM01
RUNTKA692WJQZ
RUNTKA682WJQZ
RUNTKA683WJQZ
RUNTKA693WJQZ
RUNTKA684WJQZ
RUNTKA692WJQZ
RUNTK4437TPZZ
RUNTK4437TPZA
RUNTK4437TPZB
RUNTK4437TPZC
RUNTK4462TPZZ
RUNTK4461TPZZ
RUNTK4460TPZZ
RUNTK4458TPZZ
RUNTK4459TPZZ
„OTHER UNIT
Description
MAIN Unit *1
ICON Unit
R/C LED Unit
KEY Unit
POWER/LED Drive Unit (LC-40LE810UN)
POWER/LED Drive Unit (LC-46LE810UN)
POWER/LED Drive Unit (LC-52LE810UN)
POWER/LED Drive Unit (LC-60LE810UN)
TOUCH SENSOR Unit *2
LCD CONTROL Unit (LC-40LE810UN)
LCD CONTROL Unit (LC-46LE810UN)
LCD CONTROL Unit (LC-52LE810UN)
LCD CONTROL Unit (LC-60LE810UN)
LED PWB Unit (LC-40LE810UN), x4
LED PWB Unit (LC-46LE810UN), x4
LED PWB Unit (LC-52LE810UN), x4
LED PWB Unit (LC-60LE810UN), x4
LED PWB Unit (LC-60LE810UN), x4
Ref No.
N
N
N
N
Part No.
R1LK400D3LWF2Z
R1LK460D3LWA2Z
R1LK520D3LWA2Z
R1LK600D3LW2BZ
40” LCD Panel Module Unit
46” LCD Panel Module Unit
52” LCD Panel Module Unit
60” LCD Panel Module Unit
„IC FOR EXCLUSIVE USE OF THE SERVICE
Description
Ref No.
IC509
IC2002
Part No.
VHiR24002AS1YS
RH-iXC786WJNHQ
R1EX24002ASAS0A (RGB EDID)
R5F364A6NFB (MICON)
Description
Q'ty
1
1
NOTE: *1 Replace MAIN PWB Units (DKEYMF452FM01) in case of
IC8401 or IC3302 failure.
*2 TOUCH SENSOR Unit (RUNTKA692WJQZ) reuse will be
impossible, once it is stuck on front cabinet and exfoliates.
Therefore, please exchange of a touch sensor unit in the
case of front cabinet exchange.
„SERVICE JIGS
Ref No.
N
N
N
N
N
Part No.
QCNW-C222WJQZ
QCNW-H184WJQZ
QCNW-F676WJQZ
QCNW-G405WJQZ
QCNW-G394WJQZ
Description
Connecting Cord L=1000mm 80pin LCD Control to LCD Panel Unit x2
Connecting Cord L=1000mm 12pin Main to Power Unit (PD)
Connecting Cord L=1000mm 41pin Main to LCD Control (LW)
Connecting Cord L=1000mm 4pin Main to LCD Control (PL)
Connecting Cord L=1000mm 9pin Main to Power (LB)
Q'ty
2
1
1
1
1
iv
Free Datasheet http://www.datasheet4u.com/