ISL6366.pdf 데이터시트 (총 30 페이지) - 파일 다운로드 ISL6366 데이타시트 다운로드

No Preview Available !

Dual 6-Phase + 1-Phase PWM Controller for VR12/IMVP7
Applications
ISL6366
The ISL6366 is a dual PWM controller; its 6-phase PWMs control
the microprocessor core or memory voltage regulator, while its
single-phase PWM controls the peripheral voltage regulator for
graphics, system agent, or processor I/O.
The ISL6366 utilizes Intersil’s proprietary Enhanced Active Pulse
Positioning (EAPP) modulation scheme to achieve the extremely
fast transient response with fewer output capacitors.
The ISL6366 is designed to be compliant to Intel VR12/IMVP7
specifications. It accurately monitors the load current via the
IMON pin and reports this information via the IOUT register to
the microprocessor, which sends a PSI# signal to the controller
at low power mode via SVID bus. The controller enters 1- or
2-phase operation in low power mode (PSI1); in the ultra low
power mode (PSI2,3), it can further drop the number of phases
and enable the diode emulation ofthe operational phase.In low
power modes, the magnetic core and switching losses are
significantly reduced, yielding high efficiency at light load. After
the PSI# signal is de-asserted, the dropped phase(s) are added
back to sustain heavy load transient response and efficiency.
Today’s microprocessors require a tightly regulated output voltage
position versus load current (droop). The ISL6366 senses the
output current continuously by measuring thevoltage acrossthe
dedicated current sense resistor or the DCRof the output
inductor. The sensed current flows outof the FB pinto develop the
precision voltage drop across the feedback resistor for droop
control. Currentsensing circuitsalso provide the needed signals
for channel-currentbalancing, average overcurrent protection and
individual phase current limiting. TheTM and TMS pins are to
sense anNTC thermistor’s temperature, which is internally
digitizedfor thermal monitoring and for integrated thermal
compensation of the current sense elements of therespective
regulator.
The ISL6366 features remote voltage sensing and completely
eliminates any potential difference between remote and local
grounds. This improves regulation and protection accuracy. The
threshold-sensitive enable input is available to accurately
coordinate the start-up of the ISL6366 with other voltage rails.
Features
• Intel VR12/IMVP7 Compliant
- SerialVID with Programmable IMAX, TMAX, BOOT,
ADDRESS OFFSET Registers
• Intersil’s Proprietary Enhanced Active Pulse Positioning
(EAPP) Modulation Scheme, Patented
- Voltage Feed-forward and Ramp Adjustable Options
- High Frequency and PSI Compensation Options
- Variable Frequency Control During Load Transients to
Reduce Beat Frequency Oscillation
- Linear Control with Evenly Distributed PWM Pulses for
Better Phase Current Balance During Load Transients
•D ual Outputs
- Output 1 (VR0): 1 to 6-Phase, Coupled Inductor
Compatibility, for Core or Memory
- Output 2 (VR1): Single Phase for Graphics, System Agent,
or Processor I/O
- Differential Remote Voltage Sensing
- ±0.5% Closed-loop System Accuracy Over Load, Line and
Temperature
- Phase Doubler Compatibility (NOT Phase Dropping)
• Proprietary Active Phase Adding and Dropping with Diode
Emulation Scheme For Enhanced Light Load Efficiency
• Programmable Slew Rate of Fast Dynamic VID with
Dynamic VID Compensation (DVC) for VR0
• Dynamic VID Compensation (DVS) for VR1 at No Droop
• Droop and Diode Emulation Options
• Programmable 1 or 2-Phase Operation in PSI1/2/3 Mode
• Programmable Standard or Coupled-Inductor Operation
• Precision Resistor or DCR Differential Current Sensing
- Integrated Programmable Current Sense Resistors
- Integrated Thermal Compensation
- Accurate Load-Line (Droop) Programming
- Accurate Channel-Current Balancing
- Accurate Current Monitoring
• Average Overcurrent Protection and Channel Current Limit
With Internal Current Comparators
• Precision Overcurrent Protection on IMON & IMONS Pins
• Independent Oscillators, up to 1MHz Per Phase, for Cost,
Efficiency, and Performance Optimization
• Dual Thermal Monitoring and Thermal Compensation
• Start-up Into Pre-Charged Load
• Pb-Free (RoHS Compliant)
Janu ar y 3, 20 11
FN6964.0
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 |Copyright Intersil Americas Inc. 2011. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.
http://www.Datasheet4U.com

No Preview Available !

ISL6366
Ordering Information
PART NUMBER
(Note 1, 2, 3)
PART
MARKING
TEMP. RANGE
(°C)
PACKAGE
(Pb-Free)
PKG.
DWG. #
ISL6366CRZ
ISL6366 CRZ
0 to +70
60 Ld 7x7 QFN
L60.7x7
ISL6366IRZ
ISL6366 IRZ
-40 to +85
60 Ld 7x7 QFN
L60.7x7
NOTES:
1. Add “-T*” suffix for tape and reel. Please refer to TB347 for details on reel specifications.
2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte
tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pb-
free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
3. For Moisture Sensitivity Level (MSL), please see device information page for ISL6366. For more information on MSL please see techbrief TB363.
Pin Configuration
ISL6366
(60 LD 7X7 QFN)
TOP VIEW
NC4 1
NC5 2
EN_PWR 3
RAMP_ADJ 4
RGND 5
VSEN 6
HFCOMP 7
PSICOMP 8
FB 9
COMP 10
DVC 11
IMON 12
SVDATA 13
SVALERT# 14
SVCLK 15
60 59 58 57 56 55 54 53 52 51 50 49 48 47 46
45 PWM1
44 PWM4
43 PWM2
42 PWM5
41 VCC
40 FS_DRP
GND
39 RSET
38 SICI
37 TM
36 BTS_DES_TCOMPS
35 BT_FDVID_TCOMP
34 NPSI_DE_IMAX
33 ADDR_IMAXS_TMAX
32 PWMS
31 ISENS-
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
2 FN6964.0
January 3, 2011

No Preview Available !

ISL6366
Driver Recommendation
DRIVER
QUIESCENT
CURRENT (mA)
GATE
DRIVE
VOLTAGE
# OF DIODE EMULATION
DRIVERS
(DE)
GATE DRIVE
DROP
(GVOT)
COMMENTS
ISL6627
1.0
5V Single
Yes
No For PSI# channel and its coupled channel in
coupled inductor applications or all channels
ISL6620
1.2
5V Single
Yes
ISL6620A
No For PSI# channel and its coupled channel in
coupled inductor applications or all channels.
Shorter body diode conduction time when enters
PSI2 mode at a fixed voltage.
ISL6596
0.19
5V Single
No
No For dropped phases or all channels without DE
ISL6610
ISL6610A
0.24
5V Dual
No
No For dropped phases or all channels without DE
ISL6611A
1.25
5V Dual
No
No Phase Doubler with Integrated Drivers, up to 12-
Phase. For all channels with DE Disabled
ISL6617
5.0 N/A N/A No
No PWM Doubler for DrMOS, up to 12 or 24-Phase.
For all channels with DE Disabled
ISL6625
1.2
12V Single
Yes
Yes For PSI# channel and its coupled channel in
coupled inductor applications or all channels
ISL6622
5.5
12V Single
Yes
Yes For PSI# channel and its coupled channel in
coupled inductor applications or all channels.
Shorter body diode conduction time when enters
PSI2 mode at a fixed voltage.
ISL6622A
ISL6622B
5.5
12V Single
Yes
No For PSI# channel and its coupled channel in
coupled inductor applications or all channels.
Shorter body diode conduction time when enters
PSI2 mode at a fixed voltage.
ISL6625A
1.0
12V Single
No
No For dropped phases or all channels without DE
NOTE: Intersil 5V and 12V drivers are mostly pin-to-pin compatible and allow for dual footprint layout implementation to optimize MOSFET selection and
efficiency. 5V Drivers are more suitable for high frequency and high efficiency applications.
3 FN6964.0
January 3, 2011

No Preview Available !

ISL6366
ISL6366 Internal Block Diagram
FSS_DRPS
VR_RDYS
PWMS
ISL6366A
& ISL6367
ONLY;
ISL6366
= NC4-5
ISENIN+
ISENIN-
TMS
VSENS
HFCOMPS/DVCS
FBS
RGNDS
COMPS
VR_RDY
BTS_DES_TCOMPS
BT_FDVID_TCOMP
NPSI_DE_IMAX
ADDR_IMAXS_TMAX
SVCLK
SVALERT#
SVDATA
INPUT
CURRENT
MONITOR
THERMAL
MONITOR
IIN
I_TRIP
-
OCP
+
THGS
HIGH FREQUENCY
COMPENSATION
+
OVP
-
IDROOPS
+
-
175mV
+
E/A
++ -
VR1: CLOCK AND
RAMP GENERATOR
SOFT-START
AND
FAULT LOGIC
EAPP
MODULATOR
DAC &
OFFSET
TCOMPS
SVID BUS
INTERFACE
TMAX
VR1 REGs
VR0 REGs
VR0: CLOCK AND
RAMP GENERATOR
N
TCOMPS
E/A
THGS
TEMPERATURE
COMPENSATION
AVERAGE & PEAK
CURRENT LIMIT
- 1.11V
OCP
+
IDROOPS
1.15V
LATCH
POWER-ON
RESET (POR)
RESET
- 0.85V
+
- 0.85V
+
ISL6367
I2CLK
ONLY;
ISL6366 & PMALERT#
ISL6366A
= NC1-3
I2DATA
TCOMP
PSI#
I2C /PMBUS
INTERFACE
DAC &
THGS THG IIN OFFSET
VSEN
RGND
DVC
FB
PSICOMP
X4/3
+
+
REF
SOFT-START
AND
FAULT LOGIC
+
-
175mV
+
E/A
-
HFCOMP
PSI#
IDROOP
HIGH FREQUENCY
COMPENSATION
COMP
“SICI” FOR
ISL6366:
“IAUTO” FOR
ISL6366A &
ISL6367
SICI
AUTO PHASE SHED
SHEDDING
+
1.11V OCP
-
IMON
GND
VR_HOT#
TM
1.15V
I_TRIP
1
N
TMAX
TCOMP
THERMAL
MONITOR
THG
TEMPERATURE
COMPENSATION
GAIN ADJUST
Σ
EAPP
MODULATOR
EAPP
MODULATOR
EAPP
MODULATOR
EAPP
MODULATOR
CHANNEL
CURRENT
BALANCE
AND PEAK
CURRENT LIMIT
SHED
CHANNEL
DETECT
N
TEMPERATURE
COMPENSATION
CHANNEL
CURRENT
SENSE
ISENS+
ISENS-
IMONS
FS_DRP
RAMP_ADJ
VCC
EN_VTT
EN_PWR_CFP
CFP FOR
ISL6367 &
ISL6366A
PWM1
PWM2
PWM5
PWM6
ISEN1+
ISEN1-
ISEN2+
ISEN2-
ISEN3+
ISEN3-
ISEN4+
ISEN4-
ISEN5+
ISEN5-
ISEN6+
ISEN6-
RSET
4 FN6964.0
January 3, 2011

No Preview Available !

ISL6366
Typical Application: 6-Phase Standard-Inductor VR and 1-Phase VR
+5V
VTT
SVDATA
SVALERT#
SVCLK
VR_RDY
VR_RDYS
VR_HOT#
VINF
DVC FB
PSICOMP
HFCOMP
COMP VCC PWM1
ISEN1-
ISEN1+
VSEN
RGND
EN_VTT
PWM2
ISEN2-
ISEN2+
ISL6366
+5V
VCC
PWM
BOOT
ISL6627
DRIVER
UGATE
PHASE
GND
LGATE
+5V
VCC
PWM
BOOT
ISL6627
DRIVER
UGATE
PHASE
GND
LGATE
PWM3-5
ISEN3-5-
ISEN2-5+
CFP
VINF
+5V
+5V
+5V
+5V
+5V
EN_PWR
RAMP_ADJ
IMON
IMONS
FS_DRP
FSS_DRPS
+5V BOOT
VCC
ISL6596
DRIVER
PWM6
PWM
ISEN6-
ISEN6+
ISENIN-
USED WITH ISL6366A/67
RISENIN1
RISENIN2
ISENIN+
UGATE
PHASE
GND
LGATE
VIN
RSENIN
BTS_DES_TCOMPS
BT_FDVID_TCOMP
ADDR_IMAXS_TMAX
NPSI_DE_IMAX
GND
PWMS
ISENS-
+5V
VCC
PWM
BOOT
ISL6627
DRIVER
UGATE
PHASE
GND
LGATE
ISENS+
+5V TMS
NTC
NTC
TM
SICI
RGNDS
VSENS
HFCOMPS/DVCS
RSET COMPS FBS
VINF
VINF
VINF
VINF
CPU
LOAD
GPU
LOAD
NTC: BETA = 3477
5
FN6964.0
January 3, 2011