FR1006G.pdf 데이터시트 (총 2 페이지) - 파일 다운로드 FR1006G 데이타시트 다운로드

No Preview Available !

FR1001G THRU FR1007G
Features
Isolation 10 AMPS. Glass Passivated Fast Recovery Rectifiers
Voltage Range
50 to 1000 Volts
Current
10 Amperes
TO-220
Low forward voltage drop
High current capability
High reliability
High surge current capability
Mechanical Data
Cases: TO-220 molded plastic
Epoxy: UL 94V-0 rate flame retardant
Terminals: Leads solderable per
MIL-STD-202, Method 208 guaranteed
Polarity: As marked
High temperature soldering guaranteed:
260/10 seconds .16”,(4.06mm) from
case.
Mounting position: Any
PIN 1
PIN 3
CASE
PIN 2
Positive CT
Weight: 2.24 grams
Dimensions in inches and (millimeters)
Maximum Ratings and Electrical Characteristics
Rating at 25ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%
Type Number
Symbol FR FR FR FR FR FR FR Units
1001G 1002G 1003G 1004G 1005G 1006G 1007G
Maximum Recurrent Peak Reverse Voltage VRRM 50 100 200 400 600 800 1000 V
Maximum RMS Voltage
VRMS 35 70 140 280 420 560 700 V
Maximum DC Blocking Voltage
VDC 50 100 200 400 600 800 1000 V
Maximum Average Forward Rectified Current I(AV) 10 A
Peak Forward Surge Current, 8.3 ms Single
Half Sine-wave Superimposed on Rated Load IFSM
(JEDEC method )
125
A
Maximum Instantaneous Forward Voltage
@ 5.0A
VF
1.3 V
Maximum DC Reverse Current @ TC=25
at Rated DC Blocking Voltage @ TC=125
IR
5.0 uA
100 uA
Maximum Reverse Recovery Time ( Note 1) Trr
150
250 500
nS
Typical Thermal Resistance (Note 2)
RθJC
3.0 /W
Operating and Storage Temperature Range TJ ,TSTG
-65 to +150
Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A
2. Thermal Resistance from Junction to Case Per Leg Mounted on Heatsink size 2" x
3" x 0.25" Al-Plate
- 406 -
http://www.Datasheet4U.com

No Preview Available !

RATINGS AND CHARACTERISTIC CURVES (FR1001G THRU FR1007G)
FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
50W
NONINDUCTIVE
10W
NONINDUCTIVE
(+)
50Vdc
(approx)
(-)
DUT
1W
NON
INDUCTIVE
OSCILLOSCOPE
(NOTE 1)
(-)
PULSE
GENERATOR
(NOTE 2)
(+)
+0.5A
0
-0.25A
trr
NOTES: 1. Rise Time=7ns max. Input Impedance=
1 megohm 22pf
2. Rise Time=10ns max. Sourse Impedance=
50 ohms
FIG.2- MAXIMUM FORWARD CURRENT DERATING
CURVE
12.0
-1.0A
1cm
SET TIME BASE FOR
5/ 10ns/ cm
FIG.2- TYPICAL REVERSE CHARACTERISTICS
PER LEG
1000
10.0
8.0
6.0
4.0
0.2
0
50 100
CASE TEMPERATURE. (oC)
150
FIG.3- MAXIMUM NON-REPETITIVE FORWARD
SURGE CURRENT PER LEG
150
125 8.3ms Single Half Sine Wave
JEDEC Method
100
75
50
25
12
5 10
20
NUMBER OF CYCLES AT 60Hz
50 100
FIG.4- TYPICAL JUNCTION CAPACITANCE PER LEG
300
250
200
150
100
Tj=250C
50 f=1.0MHz
Vsig=50mVp-p
0.1 0.5 1.0
5 10
50 100
REVERSE VOLTAGE. (V)
500 1000
100
Tj=1250C
10
1.0
Tj=250C
0.1
0
20 40 60
80 100 120 140
PERCENT OF RATED PEAK REVERSE VOLTAGE. (%)
FIG.6- TYPICAL INSTANTANEOUS FORWARD
CHARACTERISTICS PER LEG
80
40
20
10
4
2
1.0
.4
Tj=25oC
.2 Pulse Width=300 s
1% Duty Cycle
.1
.8 .9 1.0 1.1 1.2 1.3 1.4 1.5
INSTANTANEOUS FORWARD VOLTAGE. (V)
- 407 -