CL2200.pdf 데이터시트 (총 2 페이지) - 파일 다운로드 CL2200 데이타시트 다운로드

No Preview Available !

IMPORTANT SAFETY INSTRUCTIONS
WHEN USING YOUR TELEPHONE EQUIPMENT, BASIC SAFETY PRECAU-
TIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK AND INJURY TO PERSONS, INCLUDING THE FOLLOWING:
1. READ AND UNDERSTAND ALL INSTRUCTIONS.
2. FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE
PRODUCT.
3. UNPLUG THE PRODUCT FROM THE WALL OUTLET BEFORE CLEANING.
DO NOT USE LIQUID CLEANER OR AEROSOL CLEANERS. USE A DAMP
CLOTH FOR CLEANING.
4. DO NOT USE THIS PRODUCT NEAR WATER, FOR EXAMPLE, NEAR A
BATHTUB, WASH BOWL, KITCHEN SINK OR LAUNDRY TUB, IN A WET
BASEMENT, OR NEAR A SWIMMING POOL.
5. DO NOT PLACE THIS PRODUCT ON AN UNSTABLE CART, STAND OR
TABLE. THE PRODUCT MAY FALL, CAUSING SERIOUS DAMAGE TO THE
PRODUCT.
6. SLOTS AND OPENINGS IN THE CABINET AND THE BACK OF BOTTOM
ARE PROVIDED FOR VENTILATION, TO PROTECT IT FROM OVERHEATING.
THESE OPENINGS MUST NOT BE BLOCKED OR COVERED. THE OPENINGS
SHOULD NEVER BE BLOCKED BY PLACING THE PRODUCT ON THE BED,
SOFA, RUG OR ANY OTHER SIMILAR SURFACE. THIS PRODUCT SHOULD
NEVER BE PLACED NEAR OR OVER A RADIATOR OR HEAT REGISTER.
THIS PRODUCT SHOULD NOT BE PLACED IN A BUILT-IN INSTALLATION
UNLESS PROPER VENTILATION IS PROVIDED.
7. NEVER PUSH OBJECTS OF ANY KIND INTO THIS PRODUCT THROUGH
CABINET SLOTS AS THEY MAY TOUCH DANGEROUS VOLTAGE POINTS
OR SHORT OUT PARTS THAT COULD RESULT IN A RISK OF FIRE OR
ELECTRIC SHOCK. NEVER SPILL LIQUID OF ANY KIND ON THE PRODUCT.
CL2200 SERIES DIAGRAM
8. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT DISASSEMBLE
THIS PRODUCT. BUT TAKE IT TO A QUALIFIED SERVICE FACILITY IF
SERVICE OR REPAIR WORK IS REQUIRED. OPENING OR REMOVING
COVERS MAY EXPOSE YOU TO DANGEROUS VOLTAGES OR OTHER
RISKS. INCORRECT REASSEMBLY CAN CAUSE ELECTRIC SHOCK WHEN
THE APPLIANCE IS SUBSEQUENTLY USED.
9. UNPLUG THIS PRODUCT FROM THE WALL OUTLET AND REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL UNDER THE FOLLOW-
ING CONDITIONS:
- WHEN THE POWER SUPPLY CORD OR PLUG IS DAMAGED OR FRAYED.
- IF LIQUID HAS BEEN SPILLED INTO THE PRODUCT.
- IF THE PRODUCT HAS BEEN EXPOSED TO RAIN OR WATER.
- IF THE PRODUCT DOES NOT OPERATE NORMALLY BY FOLLOWING
THE OPERATING INSTRUCTIONS. ADJUST ONLY THOSE CONTROLS THAT
ARE COVERED BY THE OPERATING INSTRUCTIONS, AS IMPROPER
ADJUSTMENT OF OTHER CONTROLS MAY RESULT IN DAMAGE, AND
MAY REQUIRE EXTENSIVE WORK BY A QUALIFIED TECHNICIAN TO
RESTORE THE PRODUCT TO NORMAL OPERATION.
- IF THE PRODUCT HAS BEEN DROPPED OR THE CABINET HAS BEEN
DAMAGED.
- IF THE PRODUCT EXHIBIT A DISTINCT CHANGE IN PERFORMANCE.
10. AVOID USING A TELEPHONE (OTHER THAN A CORDLESS TYPE)
DURING AN ELECTRICAL STORM. THERE MAY BE A REMOTE RISK OF
ELECTRIC SHOCK FROM LIGHTNING.
11. DO NOT USE THE TELEPHONE TO REPORT A GAS LEAK IN THE
VICINITY OF THE LEAK.
PLEASE SAVE THESE INSTRUCTIONS
CONTACTING TELEDEX
Telephone
(408) 363-3100
(800) 794-8353
Internet
www.teledex.com
store.teledex.com
Email
sales@teledex.com
Postal Mail
6311 San Ignacio Avenue
San Jose, CA 95119 USA
Part Number 600-0480-49A
Copyright © 2003 Teledex LLC
ALL RIGHTS RESERVED
CL2200 SERIES USERS GUIDE
2.4 GHz Two-Line Digital Cordless Guestroom Telephone
INCLUDED IN YOUR PACKAGE
Cordless Handset
AC Adapter
Base Unit
User Guide
NiMH Battery
10-foot, 4-wire RJ-11 Line Cord
Rubber Battery Screw Cover 15-foot, 8-wire RJ-45 Cable
Phillips Screw
Clear Plastic Overlay
PREPARING TO USE THE CL2200 SERIES
1. Prepare to install the battery into the cordless handset by
firmly pressing down on the top of the battery cover and
sliding it off. If cover is secured with a screw, remove the
screw first.
2. Locate the lightly embossed numbers “1” and “2” on the
battery’s plastic connector.
3. Insert the battery connector into the handset’s connector
with the embossed numbers facing up.
Note: The handset may “beep” when the battery is connected. This is not
an indication that the telephone is ready
ance of the telephone, be sure to charge
tthoeubsae.ttTeoryobfotari1n5otpoti2m0alhpoeurrfso. rm-
4. Replace the battery compartment cover and retaining screw.
5. Insert the provided rubber screw cover.
6. Turn the telephone base so the back panel is facing you.
Insert either end of the RJ-45 cable into the jack on the back
of the telephone labeled LINE.
7. Insert the other end of the cable into the jack on the AC
adapter labeled PHONE.
8. Insert one end of the RJ-11 line cord into the jack on the AC
adapter labeled LINE.
9. Insert the other end of this line cord into a telephone jack.
10. Plug the AC adapter into an unswitched electrical outlet.
11. Once your telephone is connected, remove the plastic
overlay and place the paper faceplate over the keys. Replace
the plastic overlay by hooking the tabs on the overlay into
the recessed slots located on both sides. The overlay is
easiest to insert when the left or right side tabs are inserted
first, and the middle of the overlay is slightly bowed to allow
for insertion of the other tabs.
12. Place the cordless handset on the base unit.
CHARGING THE BATTERY
The rechargeable Nickel Metal Hydride (NiMH) battery must be
fully charged before using the phone for the first time. It is recom-
mended that that battery pack be charged for approximately 15
to 20 hours, without interruption, before use. To charge the battery,
place the handset, keypad down, in the base unit. Make sure the
CHARGE LED on the base lights. If the LED does not light:
1. Ensure that the AC adapter is plugged in.
2. Ensure that the AC adapter is not plugged into a switched
electrical outlet.
3. Ensure that the handset charging contacts at the bottom of
the handset are making good contact with the base unit’s
charging contacts.
CLEANING THE BATTERY CONTACTS
To maintain a good charge, it is important to clean all charging
contacts on the handset and base unit. Use a pencil eraser or
other contact cleaner. Do not use any liquids or solvents.
BATTERY SAFETY INSTRUCTIONS
1. Use only Teledex-approved battery replacements.
2. Dispose of used batteries according to local codes pertaining
to NiMH batteries.
3. Do not dispose of batteries in fire, as they may explode
4. Charge the telephone's batteries only while in the telephone
handset, and only by using the telephone base unit to charge.
Do not attempt to remove the batteries and charge them in
a separate charging unit.
5. Do not short-circuit the battery pack, as this may cause it to
explode or catch fire.
ADJUSTING THE RING VOLUME
The up and down volume keys will adjust the ringer volume of
the telephone. Additionally, the CL2200 series telephone has an
optional “ascending” ring volume mode, where the ring volume
begins at the lowest setting, then automatically rings louder
with each successive ring during an incoming call. To select the
ascending ring volume mode, follow these steps:
For Line 1:
Press the FLASH key; then the 4 key; then the STORE key, then
the number 1 on the keypad.
For Line 2:
Press the FLASH key; then the 4 key; then the STORE key, then
the number 2 on the keypad.
ADJUSTING SPEAKERPHONE VOLUME
The speakerphone has eight (8) levels. When the speakerphone
is activated, the volume is initially set at level six (6). To adjust
the speakerphone volume, locate the volume up/down keys,
located on the front surface of the phone below the keypad.
Pressing the “down” arrow key will decrease the volume level,
while pressing the “up” arrow key will increase it.
ADJUSTING HANDSET RECEIVE VOLUME
The handset has four (4) volume levels. The volume is initially set
at level two (2). To adjust the handset volume, locate the volume
up/down keys, located on the handset, below the “#” key.
Pressing the “minus” (-) key will decrease the volume level,
while pressing the “plus” (+) key will increase it.

No Preview Available !

AUTO DIAL KEYS
The CL2200 series has either five (5) or ten (10) programmable
guest service (auto dial) keys, depending on the model you own.
These keys can be programmed to automatically dial telephone
numbers, or to activate telephone system features. To program the
auto dial keys (programming can only be done from base unit):
1. With the faceplate removed, press the recessed STORE key.
2. Enter the desired telephone number (up to 15 digits in
length) to be stored.
3. Press the STORE key again.
4. Press the auto dial key where the number is to be stored.
Programming is now completed for that auto dial key.
To program additional keys, repeat this process.
SELECTING LINE 1 AND LINE 2
The CL2200 series employs PrimeLine/RingLine Select, which
makes selecting the correct line as easy as lifting the handset.
This feature prioritizes the ringing or idle line and reduces the
confusion of line selection.
RECEIVING A CALL
An audible ring and flickering red LED indicate an incoming call.
To answer the call using the handset while it is not on the base:
1. Pick up the handset.
2. Press the line key for the ringing line. The handset will go
“off-hook” answering the ringing line.
3. To end the call, place the handset in the base unit cradle, or
press the lit line key on the handset.
To answer the call using the handset while it is resting on the base:
1. Pick up the handset from the base. The phone will
automatically connect to the correct, ringing line.
2. To end the call, replace the handset in the base unit cradle,
or press the lit line key on the handset.
To answer the call using the speakerphone:
1. Press the line key for the ringing line. The speakerphone will
go “off-hook”, answering the ringing line.
2. Or, press the SPKR key. The phone will automatically select
the correct, ringing line.
3. To end the call, press the SPKR key again.
PLACING A CALL
Using the handset:
1. Pick up the handset and select either line 1 or line 2. Listen
for dial tone and dial the desired number.
2. After the call is complete, press the key for the selected line
again to end the call.
Using the speakerphone:
1. Press key for either line 1 or line 2, or press SPKR.
2. Listen for dial tone, and dial the desired number, or press an
auto dial key to dial a preprogrammed number.
3. After the call is complete, press the SPKR key to end call.
REDIAL
The CL2200 series can automatically redial the last number dialed.
On the handset, press the REDIAL key to redial the last number.
CONFERENCE
The CONF key allows for three-way conversations. Depending
on the situation, you may initiate a conference call using one of
these methods:
User initiates two calls:
1. Place call to first party, then place them on hold by
pressing the HOLD key.
2. Using the second line, place call to second party.
3. Once that party is on the line, press CONF to join the first
caller with the second party and yourself.
User initiates one call:
1. After receiving a call from first party, place them on hold
as above.
2. Using the second line, place call to second party.
3. Once that party is on the line, press CONF to join the first
caller with the second party and yourself.
User includes two callers:
1. After receiving a call from first party, place them on hold
as above.
2. After receiving call from second party, press CONF to join
the first party with the second party and yourself.
To terminate a conference call, pressing a line key will maintain
the connection with that line, while dropping the other line. To
terminate the call entirely, press either the CONF key or SPKR key
to disconnect both parties.
USING THE HOLD KEY
The HOLD key places the call on hold locally at the cordless
telephone.
To place a call on hold:
1. With a call active, press the red HOLD key on either the
handset or base unit.
2. The red line LED will slowly blink, indicating the call is on hold.
3. If a conference call is active, pressing HOLD will place all
connections on hold.
To remove a call from hold:
1. Press the line key of the call on hold. This will remove the
call from hold, making the call active again.
2. The red line LED will return to steady illumination, indicating
the line is active.
3. During a conference call, to remove both lines from hold,
press the CONF key.
To change phones after placing a call on hold:
1. Place the call on hold as above.
2. Pick up the call at another telephone that is on the same
line. The telephone will activate the line and remove the hold
at the original telephone.
TO MUTE THE SPEAKERPHONE
1. Press the MUTE key on the base unit. The red LED above
the MUTE key will illuminate. The party on the other end
will not be able to hear you when the MUTE LED is lit.
2. Press the MUTE key again to turn off the mute feature.
The MUTE LED will go out.
CONVERTING FROM DESK TO WALL MOUNT
The CL2200 series can be adapted for wall mounting applications.
The conversion is easiest to make when the handset and cords
are not connected.
1. Located on the handset cradle, above the speaker grill, is the
wall/desk mount clip. Remove this clip by firmly pushing it
upward towards the top of the phone.
2. Flip the clip over (top to bottom) so that the protruding edge is
towards the top of the phone and replace it in its slot. This edge
will hold the handset when the phone is mounted on the wall.
3. Turn the telephone over so the bottom is up, facing you.
Place it on a non-abrasive surface to prevent scratching.
4. Locate and remove the mounting bracket. Firmly push back
and pull up to remove two of the four retaining tabs.
5. Rotate the mounting bracket 180º degrees clockwise, so that
the mounting eyelet on the bracket is facing in the same
direction as the other mounting eyelet located on the
bottom of the telephone.
6. Insert the top two retaining tabs of the mounting brackets
into the mounting bracket slots (located near the middle of
the telephone). Then firmly push down to insert the retaining
tabs on the opposite side of the mounting bracket.
7. Connect a 15-foot RJ-45 cord into the LINE jack on the back
of the phone.
8. Turn the telephone over, and slide the telephone down onto
the mounting posts of the wall bracket. Ensure that both
eyelets line up with the mounting posts.
REQUIREMENTS OF PART 68 - FCC RULES
This device has been granted a registration number by the Federal
Communications Commission, under Part 68 rules and regulations for
direct connection to the telephone lines. In order to comply with these
FCC rules, the following instructions must be carefully read and applicable
portions followed completely:
1. Direct connection to the telephone lines may be made only through the
standard modular cord furnished, to the utility installed jack. No connection
may be made to party or coin phone lines. On the bottom of the phone is
a label that contains among other information, the FCC Registration
Number and the Ringer Equivalence number (REN) for this equipment. If
requested this information must be provided to the telephone company.
The USOC Jack for this equipment is RJ11C.
2. The telephone company, under certain circumstances, may temporarily
discontinue and make changes in facilities and services which may affect
the operation of the users' equipment: however, the user shall be given
adequate notice in writing to allow the user to maintain uninterrupted
service.
3. In certain circumstances, it may be necessary for the telephone company
to request information from you concerning the equipment which you
have connected to your telephone line. Upon request of the telephone
company, provide the FCC registration number and the ringer equivalence
number of the equipment which is connected to your line; this information
will be found on the device.
4. If any of your telephone equipment is not operating properly, you should
immediately remove it from the telephone line. It may cause harm to the
telephone network.
5. If the telephone company notes a problem, they may temporarily
discontinue service. When practical, they will notify you in advance
disconnection. If advance notice is not feasible, the telephone company
must; promptly notify you of such temporary discontinuance; afford the
opportunity to correct the condition; inform you of your rights to bring a
complaint to the FCC under their rules.
6. Repairs to the device may be made only by the manufacturer or an
authorized service agency. This applies at any time during and after
warranty. If unauthorized repair is performed, registration, connection to the
telephone lines and remainder of warranty period all become null and void.
7. This equipment is hearing aid compatible.
8. This telephone must be connected behind a PBX.
REQUIREMENTS OF PART 15 - FCC RULES
NOTE: This equipment has been tested and found to comply with the lim-
its for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful inter-
ference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accor-
dance with the instruction, may cause harmful interference to radio com-
munications. However, there is not a guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures: Move the tele-
phone away from the receiver; Consult the dealer or an experienced
radio/TV technician for help. Any changes made by the user not approved
by the manufacturer can void the user's authority to operate the telephone.
INDUSTRY OF CANADA REQUIREMENTS
NOTICE: The Industry Canada label identifies certified equipment. This
certification means that the equipment meets certain telecommunica-
tions network protective operational and safety requirements as pre-
scribed in the appropriate Terminal Equipment Technical Requirements
documents. The department does not guarantee the equipment will
operate to the users satisfaction. Before installing this equipment, users
should ensure that it is permissible to be connected to the facilities of
the local telecommunications company. The equipment must also be
installed using an acceptable method of connection. The customer
should be aware that compliance with the above conditions may not
prevent degradation of service in some situations. Repairs to certified
equipment should be coordinated by a representative designated by the
supplier. Any repairs or alterations made by the user to this equipment,
or equipment malfunctions, may give the telecommunications company
cause to request the user to disconnect the equipment. Users should
ensure for their own protection that the electrical ground connections of
the power utility, telephone lines, and internal metallic water pipe sys-
tems, if present, are connected together. This precaution may be particu-
larly important in rural areas.
Caution: Users should not attempt to make such connections themselves, but
should contact the appropriate electric inspection authority or electrician, as
appropriate.
The Ringer Equivalence Number (REN) of this device is 0.7B.
Notice: The Ringer Equivalence Number (REN) assigned to each terminal
device provides an indication of the maximum number of terminals
allowed to be connected to a telephone interface. The termination on an
interface may consist of any combination of devices subject only to the
requirement that the sum of the Ringer Equivalence Numbers of all the
devices does not exceed 5. This telephone connects to the telephone
network under the connecting arrangement code CA11A.