F1152NBGI.pdf 데이터시트 (총 20 페이지) - 파일 다운로드 F1152NBGI 데이타시트 다운로드

No Preview Available !

DATASHEET
RF to IF Dual Downconverting Mixer
GENERAL DESCRIPTION
This document describes the specifications for the
IDTF1152 Zero-DistortionTM RF to IF Downconverting
Mixer. This device is part of a series of mixers offered
with high side or low side injection options for all UTRA
bands. See the Part# Matrix for the details of all devices
in this series.
The F1152 dual channel device is designed to operate
with a single 5V supply. It is optimized for operation in
a Multi-mode, Multi-carrier BaseStation Receiver for RF
bands from 1700 - 2200 MHz with Low Side Injection
or from 1400 to 1700 MHz with High Side Injection. IF
frequencies from 50 to 350 MHz are supported.
Nominally, the device offers +43 dBm Output IP3 with
327 mA of ICC. Alternately one can adjust 4 resistor
values and a toggle pin to run the device in low current
mode with +40 dBm Output IP3 and 232 mA of ICC.
COMPETITIVE ADVANTAGE
In typical basestation receivers the RF to IF mixer
dominates the linearity performance for the entire
receive system. The Zero-DistortionTM family of mixers
dramatically improve the maximum signal levels (IM3
tones) that the BTS can withstand at a desired Signal to
Noise Ratio (SNR.) Alternately, one can run the device
in Low Current Mode to reduce Power consumption
significantly. Zero-DistortionTM technology allows
realization of either benefit.
IP3O: 9 dB STD Mode, 6 dB LC Mode
Dissipation: 40% LC
Mode, 12% STD Mode
Allows for higher RF gain
improving Sensitivity
PART# MATRIX
Part#
F1100
F1102
F1150
F1152
F1162
RF freq
range
698 - 915
698 - 915
1700 - 2200
1400 - 2200
2300 – 2700
UTRA bands
5,6,8,12,13,14,17
,19,20
5,6,8,12,13,14,17
,19,20
1,2,3,4,9,10, 33,
34,35, 36, 37,39
1,2,3,4,9,10,111,
211, 241, 33,
34,35, 36, 37,39
7,38,40,41
IF freq
range
50 - 450
50 - 250
50 - 450
50 - 350
50 – 500
Typ.
Gain
8.5
8.5
8.5
8.5
8.9
Injection
High Side
Both
High Side
Low Side
Both
1 – with High side injection
1400 - 2200 MHz F1152NBGI
FEATURES
Dual Path for Diversity Systems
Ideal for Multi-Carrier Systems
8.5 dB Gain
Ultra linear +43 dBm IP3O
Low NF < 10 dB
200 Ω output impedance
Ultra high +13 dBm P1dBI
Pin Compatible w/existing solutions
6x6 36 pin package
Power Down mode
< 200 nsec settling from Power Down
Minimizes Synth pulling in Standby Mode
Low Current Mode : ICC = 232 mA
Standard Mode: ICC = 327 mA
NOTE production BOM on p. 20
DEVICE BLOCK DIAGRAM
RFIN_A
RF VCO
RFIN_B
IFOUT_A
Bias
Control
STBY
2 LOISET
LCMODE
IFOUT_B
ORDERING INFORMATION
Omit IDT
prefix
0.8 mm height
package
Tape &
Reel
IDTF1152NBGI8
RF product Line
Green
Industrial
Temp range
IDT Zero-DistortionTM Mixer
1
Rev1, June 2012

No Preview Available !

DATASHEET
RF to IF Dual Downconverting Mixer
ABSOLUTE MAXIMUM RATINGS
VCC to GND
STBY, LCMODE
IF_A+, IF_B+, IF_A-, IF_B-, LO1_ADJ, LO2_ADJ
LO_IN, LO_IN_ALT, RF_A, RF_B
IF_BiasA, IF_BiasB to GND
RF Input Power (RF_IN[A+, A-, B+, B-])
Continuous Power Dissipation
θJA (Junction – Ambient)
θJC (Junction – Case) The Case is defined as the exposed paddle
Operating Temperature Range (Case Temperature)
Maximum Junction Temperature
Storage Temperature Range
Lead Temperature (soldering, 10s) .
1400 - 2200 MHz F1152NBGI
-0.3V to +5.5V
-0.3V to (VCC_ + 0.3V)
-0.3V to (VCC_ + 0.3V)
-0.3V to +0.3V
-0.3V to +0.3V
+20dBm
2.2W
+35°C/W
+2.5°C/W
TC = -40°C to +100°C
150°C
-65°C to +150°C
+260°C
Stresses above those listed above may cause permanent damage to the device. Functional operation of the
device at these or any other conditions above those indicated in the operational section of this specification is
not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
IDT Zero-DistortionTM Mixer
2
Rev1, June 2012

No Preview Available !

DATASHEET
RF to IF Dual Downconverting Mixer
1400 - 2200 MHz F1152NBGI
IDTF1152 SPECIFICATION
Specifications apply at VCC = +5.00V, TC = +25°C FRF = 1850 MHz, FIF = 200MHz, PLO = 0 dBm, STBY = GND, LCMODE = VIH (STD Mode),
EVKit BOM = Standard Mode, Transformer Loss included (not de-embedded) unless otherwise noted.
Parameter
Comment
Symbol min typ max units
Logic Input High
For Standby, LCMODE
Pins
VIH 2
V
Logic Input Low
For Standby, LCMODE
Pins
VIL
0.8 V
Logic Current
For Standby, LCMODE
Pins
IIH, IIL
-100
-20 µA
Supply Voltage(s)
All VCC pins
VCC
4.75 to
5.25
V
Operating
Temperature Range
Case Temperature
TCASE
-40 to
+100
degC
Supply Current
Supply Current
Supply Current
RF Freq Range
Total VCC , STD Mode
Total Both Channels
Total VCC , LC Mode
LCMODE = GND
EVkit BOM = LC Mode
Total Both Channels
Standby Mode
STBY = VIH
Total Both Channels
Operating Range (low
side injection)
ISTD
ILC
ISTBY
FRF
327 3801 mA
232 260 mA
17
1700 to
2200
26
mA
MHz
RF Freq Range
Operating Range (hi-side
inj. with RF match p. 20)
1400 -
1700
MHz
IF Freq Range
LO Freq Range
Operating Range
Low Side Injection
FIF
FLO
50 to 350
1350 to
2100
MHz
MHz
LO Power
PLO
-3 to +6
dBm
RF Input Impedance
Single Ended
Return Loss ~17 dB
ZRF
50
IF Output Impedance
Differential
Return Loss ~ 13 dB
ZIF
200
LO port Impedance
Single Ended
Return Loss ~15 dB
ZLO
50
Settling Time
Pin = -13 dBm
Gate STBY from VIH to VIL
Time for IF Signal to settle to
within 0.1 dB of final value
TSETT
0.155
µsec
Gain STD Mode
Conversion Gain
FRF = 1710 MHz
LCMODE = VIH
EVkit BOM = STD Mode
FIF = 200 MHz
GSTD 7.6 8.5 9.5 dB
IDT Zero-DistortionTM Mixer
3
Rev1, June 2012