ATM0240B20.pdf 데이터시트 (총 20 페이지) - 파일 다운로드 ATM0240B20 데이타시트 다운로드

No Preview Available !

AZ DISPLAYS
SPECIFICATIONS FOR
LIQUID CRYSTAL DISPLAY
CUSTOMER APPROVAL
PART NO. : ATM0240B20 (AZ DISPLAYS) VER1.0
APPROVAL
COMPANY
CHOP
CUSTOMER
COMMENTS
AZ DISPLAYS ENGINEERING APPROVAL
DESIGNED BY
CHECKED BY
APPROVED BY
WJQ
LIUH
GUZH

No Preview Available !

ATM0240B20(AZ DISPLAYS) TFT MODULE VER1.0
REVISION RECORD
REVISION REVISION DATE
PAGE
CONTENTS
VER1.0
2015-06-26
FIRST ISSUED
AZ DISPLAYS
1

No Preview Available !

ATM0240B20(AZ DISPLAYS) TFT MODULE
CONTENTS
1. GENERAL SPECIFICATIONS
2. PIN ASSIGNMENT
3. OPERATING SPECIFICATIONS
4. OPTICAL SPECIFICATIONS
5. RELIABILITY TEST
6. PRECAUTION FOR USING LCM
7. MECHANICAL DRAWING
8. INSPECTION SPECIFICATION
VER1.0
AZ DISPLAYS
2

No Preview Available !

ATM0240B20(AZ DISPLAYS) TFT MODULE VER1.0
1. GENERAL SPECIFICATIONS
Item
1. LCD size
2. Driver element
3. Resolution
4. Display mode
5. Dot Pitch (W*H)
6. Active Area(W*H)
7. Module size (W*H)
8. Color arrangement
9. Driver IC
10. Interface
11. Viewing angle
12. RoHS
Specification
2.4 inch(Diagonal)
a-Si TFT active matrix
240x(RGB)x320
Normally Black,Transmissive (IPS)
0.153mm(W) x 0.153mm(H)
36.72mm(W) x 48.96mm(H)
42.72mm(W) x 60.26mm(H) x 2.1mm(D)
RGB-stripe
IILI9341
See the MCU Selection interface
All
RoHS compliant
Note 1: Please refer to mechanical drawing.
Remark
Note 1
AZ DISPLAYS
3

No Preview Available !

ATM0240B20(AZ DISPLAYS) TFT MODULE VER1.0
2. PIN ASSIGNMENT
FPC Connector is used for the module electronics interface. The recommended model is
“FH19SC-40S-0.5SH" manufactured by Hirose.
NO Symbol
1 GND
2 IOVCC
3 VCC
IM2
4
IM1
5
6 IM0
Ground
Function
Power supply for internal circuit, 2.8V typical
Power supply(3.3V)
Select the MCU interface
IM2 IM1 IM0 Interface type
0 0 0 DBI Tyb_8bit interface
0 0 1 DBI Tyb_16bit interface
0 1 0 DBI Tyb_9bit interface
0 1 1 DBI Tyb_18bit interface
1 0 1 3-Wire 9 BIT DATA
interface
1 1 0 4-Wire 8 BIT DATA
interface
NOTE:
1.If not use PIN,fix to the GND ,IOVCC or NC.
2.If use RGB mode must select serial interface
serial
serial
BD in use
DB7-DB0
DB15-DB0
DB8-DB0
DB17-DB0
SDA SCL CS
SDA SCL CS RS
7 RESET
8 CS
9 DC
10 WR
11 RD
12 VSYNC
13 HSYNC
14 EN
15 DCLK
16 SDA
17-
34
DB0-DB17
35 SDO
36 NC
37 LEDA
38 LEDK
39 NC
40 GND
Reset the chip
Chip select
Data or command select pin
Write enable
Read enable
Frame synchronizing signal for RGB interface operation
Line synchronizing signal for RGB interface operation
Data enable signal for RGB interface operation
Dot clock signal for RGB interface operation
Serial in/out signal.
Data bus
Serial output signal.
No connection
LED anode
LED cathode
No connection
Ground
I: input, O: output, P: Power
I/O
P
P
P
I
I
I
I
I
I
I
I
I
I
I
I
I/O
I/O
O
-
P
P
-
P
AZ DISPLAYS
4