Maker : Analog Devices
Part No. : ADL5360

Datasheet PDF : ADL5360.pdf
Cross Reference : ADL5360 Cross Reference
Buy Component : ADL5360 Find Stock and Price

Shortcut : ADL5360  ADL5365  ADL5367 

Product Information

Preliminary Technical Data FEATURES RF Frequency 700MHz to 1000MHz IF Frequency 50MHZ to 350MHz Power Conversion Gain of 8.5dB SSB Noise Figure of 9.5dB SSB NF with +10dBm blocker of 16.5dB Input IP3 of 26dBm Input P1dB of 10 dBm Typical LO Drive of 0 dBm Single-ended, 50Ω RF and LO Input Ports High Isolation SPDT LO Input Switch Single Supply Operation: 3.3 to 5 V Exposed Paddle 6 x 6 mm, 36 Lead LFCSP Package Dual 900MHz Balanced Mixer with Low Side LO Buffer, IF Amp, and RF Balun ADL5360 APPLICATIONS Cellular Base Station Receivers Main and Diversity Receiver Designs Radio Link Downconverters GENERAL DESCRIPTION The ADL5360 utilizes two highly linear doubly balanced passive mixer cores along with integrated RF and LO balancing circuitry to enable single-ended operation. The ADL5360 incorporates two RF baluns allowing for optimal main and www.DataSheet4U.com diversity mixer performance over a 700 to 1000 MHz RF input frequency range using low-side LO injection. The balanced passive mixer arrangement provides good LO to RF leakage, typically better than -25dBm, and excellent intermodulation performance. The balanced mixer cores also provide extremely high input linearity allowing the device to be used in demanding cellular applications where in-band blocking signals may otherwise result in the degradation of dynamic performance. High linearity IF buffer amps follow the passive mixer cores, to yield a typical power conversion gain of 9.5dB. (For a higher IIP3 version of the dual mixer without the IF amplifiers, please contact the factory). The ADL5360 provides two switched LO paths that can be utilized in TDD applications where it is desirable to rapidly alternate between two local oscillators. LO current can be externally set using a resistor to minimize DC current REV. PrA Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective companies. Figure 1. Functional Block Diagram commensurate with the desired level of performance. An additional 3V logic pin is provided to power down (<100uA) the circuit when desired. For low voltage applications, the ADL5360 is capable of operation at voltages down to 3V with substantially reduced DC current. The ADL5360 is fabricated using a BiCMOS high performance IC process. The device is available in a 6mm x 6mm 36-lead LFCSP package and operates over a −40°C to +85°C temperature range. An evaluation board is also available. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. www.analog.com Tel: 781.329.4700 Fax: 781.326.8703 © 2008 Analog Devices, Inc. All rights reserved. ADL5360 ADL5360—Specifications at VS=5V Preliminary Technical Data Table 1. VS = 5 V, TA = 25°C, fRF = 900 MHz, fLO = 703 MHz, LO power = 0 dBm, Zo = 50Ω, unless otherwise noted Parameter RF INPUT INTERFACE Return Loss Input Impedance RF Frequency Range OUTPUT INTERFACE Output Impedance IF Frequency Range DC Bias Voltage LO INTERFACE LO Power Return Loss 1 Conditions Min Typ 12 50 Max Unit dB Ω Tunable to >20dB over a limited bandwidth 700 Differential impedance, f = 200 MHz 40 Externally generated 4.75 -6 Tunable to >20dB over a limited bandwidth VS 0 12 50 200 1000 MHz Ω 450 5.25 +10 MHz V dBm dB Ω MHz Input Impedance LO Frequency Range DYNAMIC PERFORMANCE Power Conversion Gain Voltage Conversion Gain SSB Noise Figure SSB Noise Figure Under-Blocking Input Third Order Intercept Input Second Order Intercept Input 1 dB Compression Point LO to IF Output Leakage LO to RF Input Leakage RF to IF Output Isolation RFI1 to RFI2 Channel Isolation IF/2 Spurious IF/3 Spurious ...

Link URL